• Textile Coloration and Finishing
• /
• v.14 no.6
• /
• pp.335-341
• /
• 2002

The physical properties and the dyeability of the nylon S fibers Prepared by high speed spinning according to godet roller draw ratio form 1.1 to 1.6 were investigated. The strains of nylon 6 fibers were decreased against the increase of the godet roller draw ratio. The stresses of nylon 6 fibers were increased with the increase of the godet roller draw ratio. Birefringences, densities and crystallinities of the nylon 6 fibers were increased with the increase of godet roller draw ratio In DSC diagrams, the $\gamma$ form of crystal became dominant at higher godet roller draw ratio. The dye uptakes of C. 1. Acid Blue 113 on the fibers were decreased against the increase of godet roller draw ratio.

• Journal of the Korean Society of Industry Convergence
• /
• v.2 no.1
• /
• pp.27-33
• /
• 1999

Effects of spinning speed and draw ratio on structure and mechanical properties of PP filament. A The crystalline structure and mechanical properties of uniaxially deformed polypropylene filament has been examined by XRD, birefringence, UTM and density method. Uniaxially deformed PP filament was prepared of various spinning speeds (300, 600, 900m/min.) and draw ratio(x2, x3, x4). From the results of these studies, it found the following facts. Firstly, it was found that the crystallinity and crystallite size (110plane) of the samples were increased with increasing of spinning speed and draw ratio, especially, it was rapidly increased between as spun yarn and 2 times draw ratio. Secondly, birefringence value was increased with increasing of spinning speed and draw ratio. The mechanical properties of initial modulus, tensile strength were increased with increasing of spinning speed and draw ratio also, but the degree of elongation decreased as spinning speed and draw ratio.

• Textile Coloration and Finishing
• /
• v.20 no.2
• /
• pp.47-52
• /
• 2008

Nylon textured yarn is usually manufactured by disk type false twist texturing. Dyeing properties of nylon textured yam have not been studied yet. In this study, dyeing properties of nylon textured yam according to draw ratio out of process parameters were investigated. The fact that microstructure of nylon textured yarn in amorphous region particularly is transformed by draw ratio was confirmed indirectly by measurement of dyeing rate because dyeing rate was affected by the structure of amorphous region. Dyeing rate at draw ratio 1.29 was the lowest because the higher draw ratio increase amorphous orientation and disturb dye diffusion into amorphous region. The microstructure according draw ratio was indirectly confirmed by 5% strength, tenacity, elongation. But difference in K/S value and fastness was insignificant.

• Fashion & Textile Research Journal
• /
• v.12 no.4
• /
• pp.500-507
• /
• 2010

In this study, physical properties were studied by using latent stretching yarn in order to develop the texturing yarn technique for super bulky yarn, which is better in bulkiness and handle than natural wool and also adds property of synthetic fiber to natural wool. In order to obtain textured conditions by analysing basic properties for manufacturing DTY yarn with super bulky property, DTY 50d/12 after spinning latent yarn spined POY 80d/12 was obtained under the two conditions of (i) false twist(T/M) level 3 in DTY texturing and (ii) draw ratio level 4 in draw texturing. For DTY texturing yarn, Elongation rate increased as the heat treatment time and temperatures increased. In addition, shrinkage became higher as false twist was higher, so that elongation rate became lower. When annealing became longer in time and higher in temperature, initial modulus increased. In addition, as the count of false twist increased, the initial modulus showed higher values. For draw texturing yarn, under the conditions of heat temperature 180 and heating time 30 minutes, shrinkage rate in draw ratio 1.55 and 1.6 draw ratio was 7%, and that in 1.65 and 1.7 draw ratio was 8.5%. High draw ratio samples' tenacity was much influenced by heating time and temperature, but low draw ratio samples' tenacity was influenced not by treated time, but by treated temperature.

• Textile Coloration and Finishing
• /
• v.12 no.2
• /
• pp.103-110
• /
• 2000

To examine the physical properties of POY through the microstructure control, the crystal structure such as the crystallinity, the crystallite size, the orientation, the shrinkage, the tensile properties, and the thermal stress of POY(80/48, SD) were examined at different draw ratios and annealing temperatures. From the examination following conclusions were obtained : 1. The crystallinity was more effected by the heat setting temperature than by the draw ratio. The increasing rate was greatest at the heat setting temperature range of $170~190^\circ{C}$. 2. The crystallite size perpendicular to the fiber axis was more effected by the annealing temperature at lower draw ratios. On the other hand, the crystal and amorphous orientations were more effected by the heat setting at higher draw ratios. 3. The boiling shrinkage did not change significantly, but the total shrinkage showed 13% at the draw ratio 1.9 and the heat setting temperature $170^\circ{C}$. 4. The maximum thermal stress increased with increasing the draw ratio and decreasing the heat setting temperature in the temperature range of $170~210^\circ{C}$. At the draw ratio 1.9 and the heat setting temperature $170^\circ{C}$, the maximum thermal stress found was 1.1gf/d. 5. In the heat setting temperature above $170^\circ{C}$ after the drawing, the crystallinity, the crystallite size, the orientation, and the strength increased with increasing temperature, but the shrinkage and the maximum thermal stress decreased with increasing temperature.

• Textile Coloration and Finishing
• /
• v.20 no.1
• /
• pp.28-35
• /
• 2008

Texturing is the process of including a characteristic of a natural fiber in a synthetic fiber. The most common method of it the false twist texturing. Nylon textured yarn is primarily manufactured by the disk type. The major process parameters or the disk type false twist machine ratio, disk/yarn, and heater temperature. This study therefore investigated the effects of false twist texturing, especially speed and draw ratio, on the physical properties of nylon textured yarn. The increase of speed was proportional to the increase of unwinding tension, which could reduce the production efficiency by elevating the tension affecting to fiber during the process. In addition, the increase of speed was inversely proportional to the increase of crimp rigidity of nylon textured yarn. Draw ratio was proportionally increased with the increase of tenacity and the reductions of fineness and elongation, showing the influence or draw ratio to the ultimate physical properties of textured yarn.

• Textile Coloration and Finishing
• /
• v.16 no.1
• /
• pp.1-4
• /
• 2004

This research surveys the twisting and untwisting tensions according to the various processing conditions of belt type texturing such as draw ratio, 1st heater temperature and velocity ratio. The 1st heater temperature was changed from 1606{\circ}C\; to\; 220^{\circ}C$, draw ratio was changed from 1.6 to 1.9 and velocity ratio was changed from 1.4 to 1.8. The twisting and untwisting tensions are measured with the variation of these processing conditions, in addition, the untwisting tension(T2) and tension ratio(T2/Tl) according to the various processing conditions are analysed with the false twist mechanism which is affected to the physical properties of draw textured yams.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1992.03a
• /
• pp.71-82
• /
• 1992

The frictional characteristics of Zn-Ni coated steel sheets were investigated by draw bead test and strip draw test. In strip draw test, the frictional characteristics were evaluated by the drawing force ratio (Tc/Ts) for half coating-stripped specimens. It is clarified that the drawing force ratio obtained by strip draw test is a convenient parameter compared to coefficient of friction obtained by draw bead test to evaluate the frictional characteristics of Zn-Ni coated steel sheets.

• Textile Coloration and Finishing
• /
• v.22 no.3
• /
• pp.272-281
• /
• 2010

This paper surveys the effects of drawing conditions of the worsted staple yarns on the mechanical properties of the knitted fabrics for highly aesthetical fabrics. The drawn worsted yarns were made on the yarn drawing system with various draw ratios under the fixed conditions of setting time, reduction and oxidation. The knitted fabric specimens were prepared on the 16 gauge circular knitting machine using these drawn worsted staple yarns. The tensile, shear, bending, compression and surface properties of these knitted fabrics were measured by KES-FB-AUTO-A system and also discussed with the drawing conditions. The tensile linearity, shear stiffness and bending rigidity decreased with increasing draw ratio. Any changes were not shown on the compressional properties with drawing conditions. But the friction coefficient of the knitted fabric on the course direction increased with increasing draw ratio, while there was no change according to the draw ratio on the wale direction.

• Textile Coloration and Finishing
• /
• v.3 no.1
• /
• pp.8-16
• /
• 1991

In order to investigate the fine structure of PET films, PET films were stretchd at various draw ratios (2, 3, 4, 5) below $T_g$ ($72^{\circ}C$) and then annealed at various temperatures (125, 150, 175, $200^{\circ}C$) under free-annealed (FA) and taut-annealed (TA) conditions. Such changes as thermal shrinkage, crystallinity, crystallite size, dynamic viscoelasticity and thermal behaviour were measured in relation to the draw ratio and annealing condition.The following results were obtained. 1. Thermal shirinkage increased with increasing annealing temperature and draw ratio, but decreased in case of draw ratio 4 (draw ratio 3 at $200^{\circ}C$) and above it. 2. The degree of crystallinity of FA samples were higher than those of TA samples. 3. Tan 5 of TA samples were less than those of FA samples, and storage moduli (E') and loss moduli (E") of FA samples were less than those of TA samples; moreover, maximum tan '||'&'||' temperature of FA samples were shifted toward higher temperature than those of TA samples. 4. The melting endotherm ($T_m$) and heat of fusion $(\DeltaH)$ of the PET film increased with the draw ratio and annealing temperature; in addition, premelting endotherm ($T_m$) and heat of fusion $(\DeltaH)$ of the local crystallization in the FA samples were larger than those of TA samples. 5. The X-ray diffraction pattern displayed sharp peaks gradually with the draw ratio and annealing temperature. 6. Crystallite sizes of FA samples were larger than those of TA samples.