• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.363-368
• /
• 2004

Maglev vehicles, which are levitated and propelled by electromagnets, often run on elevated guideways comprised of steel, aluminum and concrete. Therefore, an analysis of the dynamic interaction between the Maglev vehicle and the guideway is needed in the design of the critical speed, ride, controller design and weight reduction of the guideway. This study introduces a dynamic interaction simulation technique that applies FEM. The proposed method uses FEM to model the elevated guideway and the Maglev vehicle, which is different from conventional studies. Because the proposed method uses FEM, it is useful to calculate the deformation of the elevated guideway, the dynamic stress, and the motion of the vehicle. By applying the proposed method to an urban transit Maglev vehicle, UTM01, the dynamic response is simulated according to velocity increase and can be reviewed again. From the result of the study, we concluded that FEM simulation of the dynamic interaction between the maglev vehicle and the guideway is possible.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.243-244
• /
• 2002

New type slider with optical components is coming on market for portable and high capacity drive, and it shows great potential in future high performance drive. It is very important that a slider should have a good dynamic behavior. In this paper the dynamic behavior and static characteristics of slider have been investigated numerically by in-house simulation code using FEM.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.195-198
• /
• 2003

High temperature deformation and softening behavior of SAF 2507 super duplex stainless steel (SDSS) has been investigated in connection with an FEM analysis of hot forging process. Flow curves at various strain rates and temperatures were determined first from compression tests, and the kinetics of dynamic recrystallization were also formulated through the analysis of load relaxation test results. Applying the dynamic materials and proposed by Prasad et al., it was possible to determine the characteristics of deformation behavior effectively at a given condition of deformation. Constitutive relations and recrystallization kinetics formulated from the test results were then implemented in a commercial FEM code. Flow stress compensation formulated upon the volume fraction of recrystallization and adiabatic heating was found to improve significantly the FEA solutions in predicting the forming load and the distribution of recrystallized volume fraction after forging.

• Transactions of Materials Processing
• /
• v.12 no.4
• /
• pp.308-313
• /
• 2003

High temperature deformation and softening behavior of SAF 2507 super duplex stainless steel (SDSS) has been investigated in connection with an FEM analysis of hot forging process. Flow curves at various strain rates and temperatures were determined first from compression tests, and the kinetics of dynamic recrystallization were also formulated through the analysis of load relaxation test results. Using the dynamic materials theory proposed by Prasad, the deformation behavior was effectively determined for various conditions. Constitutive relations and recrystallization kinetics formulated from the test results were then implemented in a commercial FEM code. The forming load as well as the distribution of recrystallized volume fraction after forging was successfully predicted by means of the flow stress compensation formulated upon the volume fraction of recrystallization and adiabatic heating.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.4
• /
• pp.596-602
• /
• 2008

This paper presents the dynamic characteristic analysis of Permanent Magnet Linear Synchronous Motor(PMLSM) according to variable load. In order to analyze dynamic characteristics, finite element method(FEM) was used for calculation of the parameter and the Matlab simulink was used for dynamic characteristic simulation. The measuring system of the dynamic characteristics was manufactured and the experiment results were compared with the simulation results.

• Smart Structures and Systems
• /
• v.19 no.5
• /
• pp.499-512
• /
• 2017

Traditional structural dynamic analysis and Structural Health Monitoring (SHM) of large scale concrete civil structures rely on manufactured embedding transducers to obtain structural dynamic properties. However, the embedding of manufactured transducers is very expensive and low efficiency for signal acquisition. In dynamic structural analysis and SHM areas, piezoelectric transducers are more and more popular due to the advantages like quick response, low cost and adaptability to different sizes. In this paper, the applicable feasibility assessment of the designed "artificial" piezoelectric transducers called Concrete Piezoelectric Smart Module (CPSM) in dynamic structural analysis is performed via three major experiments. Experimental Modal Analysis (EMA) based on Ibrahim Time Domain (ITD) Method is applied to experimentally extract modal parameters. Numerical modal analysis by finite element method (FEM) modeling is also performed for comparison. First ten order modal parameters are identified by EMA using CPSMs, PCBs and FEM modeling. Comparisons are made between CPSMs and PCBs, between FEM and CPSMs extracted modal parameters. Results show that Power Spectral Density by CPSMs and PCBs are similar, CPSMs acquired signal amplitudes can be used to predict concrete compressive strength. Modal parameter (natural frequencies) identified from CPSMs acquired signal and PCBs acquired signal are different in a very small range (~3%), and extracted natural frequencies from CPSMs acquired signal and FEM results are in an allowable small range (~5%) as well. Therefore, CPSMs are applicable for signal acquisition of dynamic responses and can be used in dynamic modal analysis, structural health monitoring and related areas.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.6
• /
• pp.1773-1783
• /
• 1996

Finite element method(FEM) is one of the most popularly used method analyzing the dynamic behaviors of structures. But unless number of finite elements is large enough, the results from FEM some what different from exact analytical solutions, especially at high frequency range. On the other hand, as the spectral analysis method(SAM) deals directly with the governing equations of a structure, the results from this melthod cannot but be exact regardless of any frequency range. However, the SAM can be applied only to the case where a structure is subjected to the concentrated loads, despite a structure could be unddergone distributed loads more generally. In this paper, therefore, new spectral analysis algorithm is introduced through the spectral element method(SEM), so that it can be applied to anlystructures whether they are subjected to the concentrated loads or to the distributed loads. The results from this new SEM are compared with both the results from FEM and the exact analytical solutions. As expected, the results from new SEM algorithm are found to be almost identical to the exact analytical solutions while those from FEM are not agreed well with the exact analytical solutions as the mode number increases.

• Journal of the Korean Institute of Navigation
• /
• v.25 no.1
• /
• pp.45-52
• /
• 2001

The purpose of this study is the optimum modification of dynamic characteristics of stiffened plate structure. In the method of the optimization, finite element method(FEM), sensitivity analysis and optimum structural modification method are used. To begin with, using FEM, the dynamic characteristics of stiffened plate structure is analyzed. Next, rate of change of dynamic characteristics by the change of design variable is calculated using the sensitivity analysis. Then, amount of change of design variable is calculated using this sensitivity value and optimum structural modification method. The change of natural frequency is made to be an objective function. Thickness of plate and cross section moment become a design variable. It is shown that the results are effective in the optimum modification for dynamic characteristics of the stiffened plate structure.

• Computers and Concrete
• /
• v.8 no.1
• /
• pp.97-110
• /
• 2011

In this paper, FEM procedure is applied to the static and dynamic analyses of R/C structures. Simple R/C shell structure is solved by using FEM procedures and the experimental evaluations are performed to represent the applicability of FEM procedure to R/C structures. Also, R/C columns are analyzed numerically and experimentally. On the basis of these results, FEM procedures are applied to the R/C cooling tower structures assembled by huge R/C shell structure and a lot of discrete R/C columns. In this analysis, the parallel computing procedures are introduced into these analyses to reduce the computational effort. The dynamic performances of R/C cooling tower are also solved by the application of parallel computations as well. From the numerical analyses, the conventional FEM procedures combined with computational technologies enables us to design the huge R/C structures statically and dynamically.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.513-516
• /
• 2000

This paper presents the analytical studies on the stress and strain of driven valve system of internal combustion engines. The stress and strain is predict using FEM. The particular interest is the dynamic strain at a specific point of the valve and valve seat. Cam and follower Assuming that one rigid surface. This study forced the effects changing Young's modulus and density of valve and valve seat contact area. It supports that the indirect method using FEM is reliable for prediction the actual displacement, stress and strain in the valve system.