• Tribology and Lubricants
• /
• v.32 no.1
• /
• pp.18-23
• /
• 2016

The effective case depth for case-hardened rolling bearing has been discussed. For this purpose, rolling contact fatigue tests for ball bearings built with inner race of various hardness values were conducted until L₁₀ calculating rating life using a bearing life test machine under radial loading. Then, the distribution of residual stress below the inner raceway, which depended on the hardness value, was measured by X-ray diffraction. As a result, the linear relationship was established between the hardness value of the inner race and the theoretical shear stress evaluated at the depth where the residual stress disappeared below the inner raceway. Based on the relationship, it could be found that the factor of safety in bearing manufacturer’s rules for the effective case depth of case hardened rolling bearings was set higher. However, it could be also found that the hardness values at the depth where the maximum shearing stress acted below the raceway surface in a tapered roller bearing hardened by the carburizing process, were not sufficient for preventing plastic deformation under the basic dynamic load rating. Consequently, further efforts were still required to reduce or to disperse the contact load on the material design of a rolling bearing in order to prolong its life.

• Journal of Ocean Engineering and Technology
• /
• v.5 no.1
• /
• pp.71-80
• /
• 1991

This paper reveals the effect of the effective case depth(ECD) on the fatigue behavior of a high-frequency induction hardened SM45C in rotated bending fatigue test. In addition, the effects of fracture modes(surface origin type, inner origin type) on it are discussed. The fatigue limit of the induction hardened steel is remarkably increased compared with that of base metal. In addition, the fatigue limit is linearly increased as the effective casedepth grows deep in the region of this experiment (ECD/R;0.23-0.49). The S-N curve and fracture mode in the induction case hardened steel are classified into two kinds, as a result : N$_{f}$<10$^{5}$ ;surface origin type fracture(at high stress), N$_{f}$>10$^{5}$ ; in ner origin type fracture(at low stress). In case of inner origin type fracture; as the effective case depth(ECD) gets deep, the fatigue limit is increased by the reason that the fracture origin moves toward center; in reverse, is decreased by reason that the compressive residual stress gets low. As a result, the increasing effect of the former is much bigger than the decreasing effect of the latter, and the fatigue limit is increased as the ECD gets deep.eep.

• Journal of the Korean Data and Information Science Society
• /
• v.19 no.2
• /
• pp.463-473
• /
• 2008

In this study, we measure damage depth and calculate effective impact speed in case of rear-end collision using real car insurance data. We study the relationship between demage depth and effective impact speed, and present statistical model for these two variables. In our real data study, 3-degree polynomial equation model is better fit to effective impact speed and demage depth than the simple linear model that are estimated in previous other studies. Damage depth is a major factor to see the extent of impact in a car collision, and by using this equation, it is possible to evaluate the severity of driver's injury.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.682-687
• /
• 2000

In this research the remaining service life of the concrete due to the steel corrosion was predicted by three cases; causing carbonation, using sea sand, using deicing salts. In case of deterioration by carbonation, effective carbonation depth, effective coverage depth and relative humidity are considered for predicting method. In case of using sea sand, predicting method is made of rust growth equation from polarization resistance method. In case of using deicing salts, predicting method is made of transformation of Fick's law. Three methods are very useful in predicting service life of concrete.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.2
• /
• pp.91-96
• /
• 2010

SCM440 steels were nitrided using pulsed dc plasma combined with inductively coupled plasma (ICP) generated by 13.56 MHz rf power in order to enhance case hardening depth. The case hardening depth was increased with rf power. The effective case-depth with ICP at 900 watt was as 1.6 times as that nitrided without ICP. The hardening depth was also increased up to 1.45 times. The compound layers formed on top surface were dense and thin when pulsed dc plasma was combined with ICP.

• Journal of Wetlands Research
• /
• v.25 no.2
• /
• pp.121-131
• /
• 2023

This study examines the possible problem in the rainfall-runoff analysis process using the VIC (Variable Infiltration Capacity) model caused by using the effective soil depth instead of the soil depth. The parameters of the model are determined as follows. First, parameters that can be determined using available numerical information are fixed. For parameters related to direct runoff and base runoff, the recommended values of the VIC model are applied. In the case of soil depth, four cases are considered: (1) the effective soil depth is applied as the soil depth, (2) 1.5 times of the effective soil depth is applied as the soil depth by reflecting the vertical structure of the soil layer, (3) 1.25 times of the effective soil depth, and (4) 2.0 times of the effective soil depth as alternative soil depths. This study simulates the rainfall-runoff for the period from 1983 to 2020 targeting the Chungju Dam and Soyang River Dam basins of the Han River system. As a result of the study, it is confirmed that when the effective soil depth is applied instead of the soil depth, direct runoff and baseflow have opposite effects, and direct runoff increases by more than 3% while base runoff decreases by the same scale. In addition, the most influential factor in the estimation of the effective soil depth in the Chungju Dam and Soyanggang Dam basins is found to be the proportion of rock outcrop area. The difference between the direct runoff ratio and the base runoff ratio in the two basins is conformed significantly different due to the influence of the rock outcrop area.

• Journal of Welding and Joining
• /
• v.32 no.4
• /
• pp.34-38
• /
• 2014

Carburizing treatments are the important way to developing fatigue strength and wear resistance. It is well known that the case depth is one of the most significant parameters determining fatigue strength. In this study, 3-point bending fatigue test was conducted to evaluate fatigue strength for the carburized depth with 18CrNiMo7-6 steel. As a result, fatigue strength increased with effective case depth decreased. It is shown that hardness in case hardened layer played principal role in the fatigue strength.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.4
• /
• pp.3991-4000
• /
• 1975

It is the aim of this study to investigate the influence of the factors in the sprayer nozzle for the travelling distance and to get nozzle design data in relation to the nozz1e with and without swirl plate. The factors of sprayer nozzle are composed of the spraying pressure, the helical angle of swirl plate, the helical groove depth of swirl plate, the distance of vortex chamber the slope of nozz1e cap, the curvature of nozzle cap and the hole diameter of nozz1e cap. The travelling distance and the size of sprayed particle are experimeted indoors by the factorial arrange-ment according to the 5 each level of the above factors. The results of this stupy are summarized as follows; 1. In the nozzle with swirl p1ate there were remarkable significance among factors each other, while without swirl plate were no significance. 2. The helical angle and groove depth in the nozzle with swirl plate were the highest effective factors. The effect of helical angle was very remarked in the quadratic curve with minium value. 3. The correlation betweenthe travelling distance and the sprayed particle size was no high and under 250 micron in the case with swirl plate, and there was higher correlation in the case without swirl plate. 4. The new ideal development of the swirl plate using of the most effective helical angle and groove depth will probably show the possiblities to make effective travelling distance over 8 meters and more over and to make average particle diameter under 300 micron.

• The Korean Journal of Emergency Medical Services
• /
• v.16 no.3
• /
• pp.103-115
• /
• 2012

Purpose : Inadequate chest compression during cardiopulmonary resuscitation(CPR) may result in the insufficient blood flow to preserve critical organ function. The study evaluated changes of quality of cardiopulmonary resuscitation over time in 30:2 CPR by laypersons and analyzed rescuer factors affecting the quality of chest compressions over time. Methods : This study was designed to know quality of CPR changes during 5 minutes. 47 students completed CPR training courses. They were performed 30:2 CPR using a manikin with Skill-Reporter for 5 minutes continuously to get data of depth, rate of chest compression, volume and correct rate of ventilation. Results : Time dependent analysis showed significant ineffective compression depth in females and under weight rescuers. In case of female, we found effective compression depth has maintained up to 2 minutes, but it decreased significantly after 2 minutes. However, underweight rescuers maintained effective compression depth up to a minute but it decreased after 1 minute. Conclusion : Although compression rate maintained over time, chest compression quality declined significantly. It suggested switching compression at an interval of 2 minutes is reasonable for 30:2 CPR by layperson but underweight rescuers may provide effective chest compression by switching shift every one minute.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.17 no.1
• /
• pp.53-61
• /
• 2013

Objectives: It is certain that Radioactive iodine thyroid uptake(RAIU) rate should be measured with the standard counts considering the thyroid gland depth in enlarged thyroid patients for the variation from geometric factors. The purpose of this paper is to consider the effects of geometric factors according to detector to source distance and the effective thyroid depth on RAIU rate with experiment test. Materials and Methods: I-131 370 kBq ($10{\mu}Ci$) point source was measured by Captus-3000 thyroid uptake system (Capintec, NJ, USA) with a change Detector-Source Distance from 20 cm to 30 cm at an interval of 1 cm. And we changed the Neck phantom surface-Source Depth in the phantom with 1 cm, 2 cm, 5 cm using the neck phantom in order to reproduce the effective thyroid depth. Results: Every experimental group follows power curve as inverse square curve ($$R2{\geq_-}0.915$$). The average count rates in the case not using a phantom and the every case applied the effective thyroid depth using a phantom was not identical each other. There was significant fluctuations upon the effective thyroid depths applied the effective thyroid depth above 1 cm in $364.4 keV{\pm}10%$ energy ROI (p<0.01). There was not significant difference between the count rates of 1 cm and 2 cm in $364.4keV{\pm}20%$ and $637.1keV{\pm}6.2%$ (p=0.354, p=0.397). In assumed RAIU rate from regression equation, $364.4keV{\pm}20%$ was lower difference than $364.4keV{\pm}10%$ as 6.42% and 5.09% per 1 cm. Every change of count rate upon depth appears decreased line on Linear Regression, but the case of $284.3keV{\pm}10%$ increased only. And also, The graphs of coefficient of variation upon depth increased as straight line on every experimental group. Conclusion: The result appears that application of $364.4keV{\pm}20%$ energy ROI is more suitable for reducing error from the effective thyroid depth. And also, we can estimate the error of 20 cm should be highly reduced than 30 cm for Inverse Square Law. Therefore, If there is not information of the thyroid depth, it is considered that the error from thyroid depth can reduce through set up energy ROIs for $364.4keV{\pm}20%$, and increase Detector-Source Distances.