• Bulletin of the Korean Chemical Society
• /
• 제27권6호
• /
• pp.847-852
• /
• 2006

Imidazolium tetrafluoroborate ionic liquids having unsaturated aliphatic side chains were synthesized and characterized. Most of them are liquid at room temperature and all of them are stable up to $300{^{\circ}C}$. Some imidazolium tetrafluoroborates with an allylic side chain showed much wider voltage windows on the platinum electrode, better conductivities, and lower viscosities compared with the corresponding ionic liquids containing the saturated side chains.

• Bulletin of the Korean Chemical Society
• /
• 제28권9호
• /
• pp.1562-1566
• /
• 2007

1-Alkenyl-2,3-dimethylimidazolium tetrafluoroborate ionic liquids having an olefinic substituent were synthesized and characterized. Among them, [AMMIm]BF4 with an allyl group showed lower viscosity, higher ionic conductivity, and a wider electrochemical window compared with its analogue having a saturated alkyl substituent. An EDLC with [AMMIm]BF4 showed better performance than that with [PMMIm]BF4, too.

• 한국시뮬레이션학회논문지
• /
• 제6권2호
• /
• pp.1-14
• /
• 1997

The characteristics of the flow and energy conversion in OMACON liquid-metal MHD system are investigated. Numerical simulation of two-phase flow in the OMACON system without magnetic field was carried out by the Phoenics code and the energy conversion characteristics are studied in association with the fact that the mechanical energy loss at the nozzle of the OMACON system are to be converted into electrical energy. In this system, working fluid (gas) is injected through the mixer located at the bottom of the riser, and is mixed with hot liquid metal. Therefore in the riser two-phase flow is developed under the influence of the gravity. In this study, the interaction between the gas and liquid is considered by the use of IPSA(InterPhase Slip Algorithm) where standard drag coefficient has been used. It has been assumed that in the flow regime the liquid is continuous and the gas is dispersed. For the liquid and gas, the continuity equations, momentum equations and energy equations are solved respectively in association with void fraction in the flow field. In order to calculate the energy conversion efficiency, firstly the ratio of the mechanical energy loss of liquid metal flow at the nozzle to the input thermal energy is considered. Secondly flow pattern of liquid metal in the generator has been analyzed, and the characteristics of the conversion of the mechanical energy into the electrical energy has been investigated. For an representative case where Hartmann number is 540 and magnetic field is 0.35 T, the present analysis shows that the energy conversion efficiency is 0.653. This result is considered to be reasonable in comparison with published experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.16-18
• /
• 2006

유한요소법을 사용한 전기기기의 해석에서는 움직임을 고려한 해석이 필수적이다. 본 논문에서는 전기기기의 유한요소 해석시 움직임을 고려하기 위한 방안으로써 Moving Suface기법을 소개하고 이 기법의 적용방법 및 장단점에 관하여 논하였다. 또한 이 기법을 검증하기 위하여 Moving Surface기법을 적용한 유한요소해석 프로그램을 개발하고, 개발한 프로그램을 사용하여 실제 모델을 해석해 그 결과치를 실험치와 비교함으로써 타당성을 입증하였다.

• 한국해양공학회지
• /
• 제4권1호
• /
• pp.43-48
• /
• 1990

The results of previous works on the wave energy conversion do not seem to be satisfactory due to irregularity, and the non-linear hydrodynamic effect which is inevitably featured due to the structural complexity of the ocean wave energy conversion device. These may cause the difficulty estimating the extracted wave power. In this paper a study on estimating the extracted wave power and its ratio. The present authors have developed another method estimating the extracted wave power using the three dimensional source distribution method, which was turned out to be an improved one. It has been observed that the present results may be used for the control of the wave energy conversion device and the optimal design has been derived from the several case studies.

• Bulletin of the Korean Chemical Society
• /
• 제28권9호
• /
• pp.1567-1572
• /
• 2007

New pyrrolidinium and piperidinium bis(trifluoromethanesulfonyl)imide (TFSI) ionic liquids (ILs) having allyl substituents were synthesized and characterized. All of them are liquid at room temperature and stable up to 300 oC. The pyrrolidinium-based ILs showed better conductivities and lower viscosities than the corresponding piperidinium-based ILs. Among them, 1-allyl-1-methylpyrrolidinium TFSI showed the lowest viscosity of 52 cP, the highest conductivity of 5.7 mS cm?1, and the most negative cathodic voltage window of ?3.2 V (vs. Fc/Fc+) on a platinum electrode, which are the improved results compared to the corresponding analogue having a saturated substituent, 1-methyl-1-propylpyrrolidinium TFSI.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2002년도 추계 학술발표회 논문집
• /
• pp.191-194
• /
• 2002

매체 순환식 연소(Chemical-Looping Combustion, CLC)는 금속 산화물(산소공여매체, oxygen carrier)의 산소를 이용하여 화석연료를 산화(연료 연소 공정)시키고, 환원된 금속을 다시 산화(매체 산화 공정)시키는 간접적인 연소 공정의 하나이다. 이 방식은 온실효과의 주발생원인 $CO_2$를 원천적으로 회수할 수 있고, 또한 화염이 없는 상태에서 연소반응이 진행됨으로 thermal NOx의 발생을 미연에 방지할 수 있어 고효율의 환경친화적인 연소공정이다.(중략)

• Bulletin of the Korean Chemical Society
• /
• 제31권9호
• /
• pp.2447-2448
• /
• 2010

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제11B권4호
• /
• pp.156-163
• /
• 2001

In this paper an optimal switching angle control of a switched reluctance motor (SRM) drive system is investigated for achieving maximum energy conversion ratio. A new magnetizing method is proposed with a low switching frequency. The proposed algorithm maximizes the positive energy conversion region, which is directly related to the mechanical output, and reduces the reactive power region with the same field energy region. As a consequence, a torque ripple is also sufficiently reduced compared with that of the conventional switching angle magnetizing method. Experimental results show that the proposed scheme provides a high efficiency and a low ripple drive.

• 문화기술의 융합
• /
• 제3권1호
• /
• pp.43-48
• /
• 2017

본 연구는 에너지 변환을 가하면 피부에 기능별 투과와 전달현상의 변화를 확인한다. 주어진 에너지의 변화로 피부에 진행되는 과정과 에너지 전달에 투과조절의 단계로 흐르는 과정을 구성하고, 알고리즘을 통하여 변화의 과정을 모델링한다. 에너지양의 조절과 과정의 처리를 모델링한 상태에서 피부의 표피 진피에 효과적 단계로 자동 조절 및 국부 조절을 통한 시스템 모델을 구성하였다. 에너지 변환에 따른 고정된 위치와 계획된 장치로 재현하는 에너지 조절기능이 크기 형태 조합을 변환시키는 모형으로인한 깊이에 따른 분포의 변화가 정확하게 얻어지도록 투과펄스시스템을 구성하였다. 따라서 효율적인 에너지 변환을 제어하는 전달시스템을 구성하기위해 변환모델을 세분화하여 구축하였다. 이를 통하여 피부효과에 기능적 에너지 조절이 가능한 투과 조절시스템이 구성되어 지속적인 피부의 개선효과가 진행 될 것으로 예상된다.