• Korean Journal of Optics and Photonics
• /
• v.16 no.2
• /
• pp.138-142
• /
• 2005

In this paper, a method to eliminate the polarization dependent properties of fiber-to-planar waveguide couplers using a thin half-waveplate is proposed and demonstrated. The operation principle of the device is explained and the fabrication technology is presented. It is experimentally shown that the resonance wavelengths of the device are independent of the polarization state of input light.

• Korean Journal of Optics and Photonics
• /
• v.14 no.4
• /
• pp.355-358
• /
• 2003

We report experimental results on the wavelength and polarization selective coupling properties of fiber-to-planar waveguide coupler having a thin metal intermediate layer. The influence of the metal layer thickness and the refractive index of the superstrate on the device properties has been measured and explained. The proposed device exhibited various application possibilities including polarizers, modulators, and sensors.

• Journal of Sensor Science and Technology
• /
• v.13 no.5
• /
• pp.350-355
• /
• 2004

A novel UV sensor was manufactured and characterized using the evanescentfield coupling between fiber-planar waveguide (PWG) coupler and prism. A spiroxazine dye was chosen as planar waveguide because its photochromic isomerization induced by UV irradiation. A novel UV sensor was proposed to measure the variation of refractive index and absorption coefficient simultaneously. The wavelength responses of these sensors by UV exposure times were measured 0.48 nm/sec, 0.757 nm/sec, and ATR output power variations were measured $-0.424{\mu}W$/sec and $-0.62{\mu}W$/sec when UV exposure power were 3 mW and 5 mW, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.2
• /
• pp.33-38
• /
• 2004

We have demonstrated a tunable Inter based on an asymmetric directional coupler made of a side-polished polarization maintaining fiber coupled with a polymer planar waveguide. The thermo-optic effects of the polymer planar waveguide induced by a micro-strip heater placed on the top layer of the device leads to shift of resonance wavelength of the coupler. The fabricated device exhibited wide tunable range exceeding 230 nm with 720 ㎽ of applied electrical power.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.28-33
• /
• 2004

An in-line fiber coupler, based on side-polished single-mode fibers covered with an intermediate coupling layer and a planar waveguide, is analyzed by modeling the interaction region as an equivalent multi-layered planar waveguide. The reflectance for the multi-layered structure with and without buffer layer is illustrated as a function of the refractive index and thickness of the overlay waveguides. When the refractive index of the overlay waveguides is greater than that of the fiber core, the conditions for the intermediate coupling layer to increase the power coupling from the fiber to the overlays is also explained. Through the experimental results using a LiNbO$_3$planar waveguide, we show that the theoretical analysis is reasonable and in good agreement with the measured values.

• Journal of Sensor Science and Technology
• /
• v.13 no.3
• /
• pp.207-212
• /
• 2004

We have investigated the optical characteristics of a directional coupler made of a side-polished polarization maintaining fiber in contact with a multimode planar waveguide and its applications as sensors. A device structural condition to achieve the polarization insensitive wavelength response has been presented. The fabricated devices revealed a superior immunity to the bending and the deformation of PM fibers in the input section. It is experimentally shown that the proposed device is suitable for a remote fiber sensor.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.7
• /
• pp.42-49
• /
• 1999

In this paper, we proposed a simple measurement method to find the behaviors of the fiber-to-waveguide coupler. The polished fiber blocks and planar waveguides on silicon dioxide were fabricated independently and then optically coupled by physical pressure. Several kinds of polymer with different refractive indices were used for waveguide films. The proposed method makes it possible to measure the center wavelength, bandwidth, extinction ratio, and polarization dependence of the coupler during fabrication procedure. The wavelength sensitivity increased with refractive index of polymer. The symmetric planar waveguide structure and isotropic property of guiding materials reduced polarization dependent property. Insertion loss of the coupler was less than 0.5dB. It is expected that our measurement method is useful for developing various optical devices using evanescent coupling between polished fiber and planar waveguide such as optical modulators and filters etc.

• Korean Journal of Optics and Photonics
• /
• v.15 no.2
• /
• pp.109-113
• /
• 2004

We have manufactured and characterized the fiber-to-Planar Waveguide Coupler for analysis of the photo-induced refractive index change of DM-BTE .(l,2-bis[2,5-dimethylthio-phen-3-yl]-hexafluorocyclopentene) When irradiated with ultraviolet light, the colorless diarylethene(DM-BTE)-crystal turned red while keeping the crystal shape. The red color was bleached by irradiation with visible light(λ＞450 nm). The resonant wavelength was shifted and recovered owing to the refractive index variation of the planar waveguide because of its photo-functional properties on exposure to UV and visible light. The wavelength responses of this switch by UV exposure were measured as 0.057 nm/sec with saturation time of 60 seconds. and when illuminated by visible light, resonance wavelength variations were measured as 0.028 nm/sec, with recovery time of 140 seconds.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.1
• /
• pp.39-46
• /
• 2002

High-senstivity temperature sensor based on the wavelength selectivity of single mode fiber-to-planar waveguide coupler, was demonstrated. The resonant wavelength of the coupler was shifted with large rate of -3.43nm/$^{\circ}C$ owing to good thermo-optic effects of polymer planar waveguide. The device design technique to reduce the polarization dependent properties and increase the temperature sensitivity was presented.

• Korean Journal of Optics and Photonics
• /
• v.12 no.5
• /
• pp.406-413
• /
• 2001

We report theoretical and experimental results for the wavelength and polarization selectivity of a fiber-to-planar waveguide coupler made of a side polished single mode fiber covered with a planer waveguide incorporating a thin metal film. A simple but exact approach to obtain the modal properties of multilayer planar waveguide with a thin metal film is described. The device was modeled into equivalent 1 dimensional structure and its behaviour was analyzed based on coupled mode theory. The effects of metal film thickness and refractive index of superstrate on the device properties were measured and explained.