• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.90-98
• /
• 2011

Al-Si coated Boron steel and Zn coated DP steel were welded using DISK laser and the microstructure and hardness of the weld were investigated. Full penetration was obtained, when the welding speed was lower than 4m/min. In the specimen welded with laser power of 3 kW and welding speed of 2 m/min, the hardness was the highest in the heat affect zone in the boron steel (HAZ-B) and that of the heat affect zone in the DP steel (HAZ-D) was lower than HAZ-B. The hardness of fusion zone was in between those of HAZ-B and HAZ-D. The decreased hardness from each HAZ to base metal(BM) could be explained that ferrite contents increases when access to the BM. The variation of hardness in the welds could be explained by the difference of microstructure, that is, full martensite in HAZ-B, mixture of martensite and bainite in the fusion zone, and the mixture of martensite, ferrite and bainite in HAZ-D.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.44 no.1
• /
• pp.78-85
• /
• 1999

To investigate kernel hardness, a compression test which is widely used to measure the hardness of individual kernels as a physical testing method was made simultaneously with the measurement of friabilin (15KDa) which is strongly associated with kernel hardness and was recently developed as a biochemical marker for evaluating kernel hardness in 79 Korean wheat varieties and experimental lines. With the scattered diagram based on the principal component analysis from the parameters of the compression test, 79 Korean wheat varieties were classified into three groups based on the principal component analysis. Since conventional methods required large amount of flour samples for analysis of friabilin due to the relatively small amount of friabilin in wheat kernels, those methods had limitations for quality prediction in wheat breeding programs. An extraction of friabilin from the starch of a single kernel through cesium chloride gradient centrifugation was successful in this experiment. Among 79 Korean wheat varieties and experimental lines 50 lines (63.3%) exhibited a friabilin band and 29 lines (36.7%) did not show a friabilin band. In this study, lines that contained high maximum force and the lower ratio of minimum force to maximum force showed the absence of the friabilin band. Identification of friabilin, which is the product of a major gene, could be applied in the screening procedures of kernel hardness. The single kernel analysis system for friabilin was found to be an easy, simple and effective screening method for early generation materials in a wheat breeding program for quality improvement.

• Journal of Korean Society on Water Environment
• /
• v.30 no.1
• /
• pp.25-30
• /
• 2014

This study is done to prove the premise that both alkalinity and hardness affect on the dissolved phosphorus concentration so that the growth of algae is also affected in water bodies like rivers and lakes. Statistical analysis of the water quality data of 13 reservoirs collected for the last decade shows the relations between alkalinity and chlorophyll-${\alpha}$ and between hardness and chlorophyll-${\alpha}$ are not linear but follow second order equation. This relation seems to be due to two antagonistic effects accompanying a simultaneous increase in alkalinity and hardness. The increase stimulates the growth of algae by supplying carbonates and $Ca^{2+}$ to algae and at same time it causes a decrease in soluble phosphorus which retards algae to grow. These opposing tendencies are confirmed by theoretical calculations with the MINTEQ model. There seems to be ranges of alkalinity and hardness that are in favor of algae growth; the ranges are less than 44 mg/L as $CaCO_3$ in alkalinity and also less than 63 mg/L as $CaCO_3$ in hardness. This finding will provide a solid base to develop an effective water quality management of water bodies.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.5
• /
• pp.571-578
• /
• 1997

The development of new approaches for wheat grain hardness assessment may impact the grain industry in marketing, milling and breeding. This experiment was to develop a new method for fast identification between softness and hardness, and for maintaining germinability of seed after measurement in wheat. Results from the comparisons of accuracy and significance between image analysis and conventional methods(NIRS and textrometer) were summarized. Data obatined from image analysis for grain hardness did not show any difference from those of the conventional methods. The protein content analyzed by micro-Kjeldahl method was significantly correlated with the grain hardness measured by image analysis, textrometer, and NIRS. The analysis for wheat grain hardness using image analysis may be used as an alternative method to the conventional methods. This method also takes the seeds after analysis can be utilized as breeding materials in early generations.

• Journal of the Korean Society for Heat Treatment
• /
• v.2 no.2
• /
• pp.33-37
• /
• 1989

In order to improve hardness uniformity of standard-hardness blocks. experimental procedure was designed using Taguchi Method. For this purpose the following factors were studied: austenitizing temperature, tempering condition, grinding condition, subzero treatment, lapping time, $15{\mu}m$ polishing time, final polishing time. These factors were processed and then ten hardness values were measured on each specimen. SN (signal to noise) ratio for each condition was calculated with standard variations of these values. Finally, from the calculated value of ANOVA on SN ratios, the lapping time was found to be the main factor Better uniformity with longer lapping time implies that residual stress that was formed after quenching is a dominent parameter that affects on the uniformity of hardness. Therefore, step-quenching method was adapted to minimize the residual stress. By this modification of quenching procedure, the hardness uniformity was improved remarkably and the yield ratio was increased from 55% to 88%.

• Korean Journal of Veterinary Research
• /
• v.14 no.2
• /
• pp.185-189
• /
• 1974

Although considerable research has been done on the blood chemistry of domestic animals, little work has been made of the changes associated with age. Moreover, the records about physiology of the goat were not much available in Korea, and a comprehensive survey of the blood chemical values of the Korean native goat has not been made. The authors intended to biometric study on the hardness of bone of race horse and Jeju horse in Korea. The measurement of hardness of bone were performed in 272 race horses (Thoroughbred 91, Anglo-Arab 107, Arab 74) and in 109 Jeju horses by the caliper by Toryba's method. Some interesting facts obtained through this study were as follows: 1. There was not significant difference of bone hardness between male and female. The average of bone hardness by the Toryba's meteod were $23.07{\pm}1.01$ in race horse and $19.44{\pm}1.84$ in Jeju horse. 2. The grade of bone hardness of race horse were higher than those of Jeju horse(P<0.001). 3. The correlation coefficient between age and grade of bone hardness were r= +0.344 in Jeju horse, theme were statistically significant (P<0.01) and the regression equation was Y=0.29x+18.497.

• Korean Journal of Occupational Health Nursing
• /
• v.23 no.1
• /
• pp.11-19
• /
• 2014

Purpose: The purpose of this study was to examine the relationship of job stress, hardness and burnout among emergency room nurses. Methods: The subjects were 110 emergency room nurses from three university hospital and three general hospital, with more than 500 beds, in G city and J region. Data collection was done from October 11 to November 12, 2010. Results: The score of job stress was 3.8 out of 5 point, the score of hardness was 2.6 out of 4 point, and the score of burnout was 3.3 out of 5 point. Burnout was found to be in a significant positive correlation with job stress and significant negative correlation with hardness. The main predictors of burnout were to hardness, job stress and night duty, and these variables explained 45.2% about burnout. Conclusion: In conclusion, the higher job stress was in higher burnout and the higher hardness was in the lower burnout. It is necessary to create improvement ways and programs to reduce and prevent burnout of emergency room nurses.

• Journal of the Korea Furniture Society
• /
• v.23 no.4
• /
• pp.435-439
• /
• 2012

This research was performed to evaluate surface performance of gold plated carbonized board. After the carbonization at $850^{\circ}C$, volume, weight, and density decreased by 65.25%, 71.35% and 17.64%, respectively. Abrasion resistance and surface hardness of non-carbonized board exhibited the highest values of 0.093 g/100 revolution and 26.43 N/$mm^2$, respectively. Gold plated carbonized board showed intermediate values, 0.587 g/100 revolution of abrasion resistance and 24.35 N/$mm^2$ of surface hardness. Carbonized board showed the lowest values, 0.863 g of abrasion resistance and 21.50 N/$mm^2$, of surface hardness. These results were thought to reflect propertional relationship between abrasion resistance and surface hardness. Abrasion resistance and surface hardness of carbonized board appeared able to be improved by surface treatment such as plating.

• Korean Journal of Materials Research
• /
• v.21 no.11
• /
• pp.581-586
• /
• 2011

This study describes a hydrogen embrittlement evaluation of the subsurface zone in 590DP steel by micro-Vickers hardness measurement. The 590DP steel was designed to use in high-strength thin steel sheets as automotive materials. The test specimens were fabricated to 5 series varying the chemical composition through the process of casting and rolling. Electrochemical hydrogen charging was conducted on each specimen with varying current densities and charging times. The relationship between the embrittlement and hydrogen charging conditions was established by investigating the metallography. The micro-Vickers hardness was measured to evaluate the hydrogen embrittlement of the subsurface zone in addition to the microscopic investigation. The micro-Vickers hardness increased with the charging time at the surface. However, the changing ratio and maximum variation of hardness with depth were nearly the same value for each test specimen under the current density of 150 mA/$cm^2$ and charging time of 50 hours. Consequently, it appears that hydrogen embrittlement in 590DP steel can be evaluated by micro-Vickers hardness measurement.

• Journal of Technologic Dentistry
• /
• v.45 no.3
• /
• pp.55-60
• /
• 2023

Purpose: This study aimed to evaluate the effects of a special heat treatment on Pd-Au-Ag metal-ceramic alloy after degassing treatment and on changes in the hardness of the alloy during the firing process. Methods: Specimen alloys were cast and subjected to degassing at 900℃ for 10 minutes. These specimens were then subjected to a special heat treatment at 600℃ for 15 minutes in a dental porcelain furnace. Further, the specimens were subjected to simulated firing in the porcelain furnace. The resulting specimens were then tested for hardness, and changes in the microstructure were observed. Results: There was a decrease in the hardness of the alloy during the simulated firing of the cast alloy due to the coarsening of the particles. Meanwhile, additional heat treatment after degassing was found to play a crucial role in preventing a decrease in hardness. This treatment effectively suppressed the coarsening of the precipitates during repeated firing at high temperatures. Conclusion: Specific heat treatment of the Pd-Au-Ag metal-ceramic alloy prevented a decrease in its hardness and extended the lifespan of the metal-ceramic prosthesis.