• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3425-3430
• /
• 2013

The fast-growing market in wireless communications has led to the development of multi-standard mobile terminals. In this paper, a frequency-tunable active RC bandpass filter for multi-standards wireless communication system is designed using an active inductor. The conventional bandpass filter design methods employ the high order filter or high quality factor Q to improve the stopband attenuation characteristics and frequency selectivity of the passband. The proposed bandpass filter based on the high Q active inductor has an improved frequency characteristics. The center frequency and gain of the designed bandpass filter is tuned by employing the tuning circuit. We have performed the simulation using TSMC $0.18{\mu}m$ process parameter to analyze the characteristics of the designed active RC bandpass filter. The bandpass filter with Q=20.5 has 90MHz half power bandwidth at the center frequency of 1.86GHz. Moreover, the center frequency of the proposed bandpass filter can be tuned between 1.86~2.38GHz for the multi-standards wireless communication system using the capacitor of the tuning circuit.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.86-89
• /
• 2002

A new design approach for realising low-power low-voltage high-Q high-order RE bandpass filter is proposed. Based on the gyrator-C inductor topology, a 2$\^$nd/-order biquadratic bandpass filter can be realised by adding a series capacitor to the input port of the gyrator. High-Q 2$\^$nd/-order and 4$\^$th/-order fully differential RF bandpass filters operating in the 2.4-㎓ ISM (Industrial, scientific and medical) frequency band under a 2-V single power supply voltage with low power dissipation are reported.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.237-240
• /
• 2005

A novel current mode high Q bandpass filter with electronically tuable values of Q based on second generation current controlled conveyor CCCIIs is presented. The circuit offers the advantages of using a few passive elements. The center frequency and pole-Q can be independently adjusted by via dc bias current of CCCIIs, It is shown from SPICE simulation that the results agree well with theoretical analysis

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.37-44
• /
• 2007

A low-voltage high-linear bipolar OTA and its application to IF bandpass filter for GSM cellular telephone are presented. The OTA consists of a low-voltage linear transconductor, a translinear current gain cell, and three current mirrors. The bandpass filter is composed of two cascaded identical second-order bandpass filters, which consist of a resistor, a capacitor, and a grounded simulated inductor realized with two OTA's and a grounded capacitor. SPICE simulations using an 8 GHz bipolar transistor-array parameter show that the OTA with a transconductance of 1 mS exhibits a linearity error of less than ${\pm}2%$ over an input voltage range of ${\pm}0.65\;V$ at supply voltages of ${\pm}2.0\;V$. Temperature coefficient of the transconductance is less than $-90ppm/^{\circ}C$. The bandpass filter has a center frequency of 85 MHz and Q-factor of 80. Temperature coefficient of the center frequency is less than $-182ppm/^{\circ}C$. The power dissipation of the filter is 128 mW.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.11
• /
• pp.2127-2130
• /
• 2008

In this paper, a tunable bandpass filter with mutual inductive coupling circuits is newly designed and demonstrated for UHF TV tuner ranged from Ch.14(473MHz) to Ch.69(803MHz) applications. Conventional HF tuning circuit with an electromagnetic bandpass filter has several problems such as large size, high volume and high cost, since the electromagnetic filter is comprised of several passive components and air core inductors to be assembled and controlled manually. To address these obstacles, peaking chip inductor was newly applied for constructing the mutual inductive coupling circuit. The proposed circuit was newly and optimally designed, since the chip inductor showed lower components Q-value than the air core inductor. A varactor diode has been also used to fabricate the proposed tunable bandpass filter for RF tuning circuit. The fabricated tunable filter exhibited low insertion loss of approximately -3dB, high return loss of below -10dB, and large tuning bandwidth of 330MHz.

• Journal of Navigation and Port Research
• /
• v.31 no.9
• /
• pp.759-762
• /
• 2007

A novel miniaturized CMOS C-Band bandpass filter based on diagonally end-shorted coupled lines and interdigital capacitors is proposed. The utilized coupled lines structure reduced the configuration in size, as small as a few degrees. Moreover, the characteristic of interdigital capacitor, relatively high Q and good capacitance tolerance, accounts for the satisfied performance of this new filter. A two-stage bandpass filter was designed and fabricated with chip surface area only $1.02{\times}1.4\;mm^2$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.11
• /
• pp.89-94
• /
• 2008

In this paper, a cascade of a wideband amplifier and a high-Q bandpass filter (BPF) has been realized in a 0.18mm CMOS technology for the applications of subsampling direct-conversion receivers. The wideband amplifier is designed to obtain the -3dB bandwidth of 5.4GHz, and the high-Q BPF is designed to select a 2.4GHz RF signal for the Bluetooth specifications. The measured results demonstrate 18.8dB power gain at 2.34GHz with 31MHz bandwidth, corresponding to the quality factor of 75. Also, it shows the noise figure (NF) of 8.6dB, and the broadband input matching (S11) of less than -12dB within the bandwidth. The whole chip dissipates 64.8mW from a single 1.8V supply and occupies the area of $1.0{\times}1.0mm2$.

• ETRI Journal
• /
• v.26 no.4
• /
• pp.292-296
• /
• 2004

In this paper we present a new current-mode electronically tunable universal filter using only plus-type current controlled conveyors (CCCII+s) and grounded capacitors. The proposed circuit can simultaneously realize lowpass, bandpass, and highpass filter functions - all at high impedance outputs. The realization of a notch response does not require additional active elements. The circuit enjoys an independent current control of parameters $\omega_0$ and $\omega_0/Q$. No element matching conditions are imposed. Both its active and passive sensitivities are low.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.1
• /
• pp.30-38
• /
• 2015

In this paper, the design of a compact triple-mode bandpass filter using a high-Q cylindrical dielectric resonator is proposed. In detail, the triple $TE_{01{\delta}}$ modes along three orthogonal axes are used and novel coupling structure in the metallic enclosure is adopted to introduce the coupling between the resonant modes. Due to the cross coupling, the proposed bandpass filter has an asymmetric frequency response with flexible three transmission zeros, one of which can be located very close to the passband edge to provide an extremely sharp skirt characteristic with low insertion loss. The proposed filter is about 60 % miniaturized compared with conventional single-mode dielectric resonator filter. The proposed bandpass filter design is validated by the circuit and 3D EM simulations and measurements compared to the target specifications.

• Journal of Advanced Navigation Technology
• /
• v.4 no.1
• /
• pp.36-44
• /
• 2000

A frequency-shifting technique that uses a digital filter in order to interpolate a bandpass-sampled signal at a low-pass position is investigated. The discussion focuses on the derivation of the required digital filter. It is shown that second-order bandpass sampling offers more flexibility than first-order bandpass sampling in the sense of sampling frequency choice. It is also shown that the well-known quadrature-sampling method for frequency-shifting is a special case of the general second-order sampling technique. The advantages of the mixer-free digital quadrature demodulations are increased flexibility for sampling frequency choice and high precision for I/Q component extraction, and this type of modulation can be applied for modern radar signal processing with high performance.