• Journal of electromagnetic engineering and science
• /
• v.12 no.1
• /
• pp.63-69
• /
• 2012

This paper presents the design of a calculable standard dipole antenna with a hybrid balun in the frequency range of 1 GHz to 3 GHz. A new formula of the antenna factor for a dipole antenna with a hybrid balun is derived using the power mismatch-loss concept. The antenna factors derived in this paper are in good agreement with the results calculated from S-parameters. The design results show that the calculable dipole antenna with a hybrid balun can be characterized by power mismatch-loss component factors.

• Journal of electromagnetic engineering and science
• /
• v.15 no.3
• /
• pp.185-193
• /
• 2015

In this paper, a hybrid multiple input multiple output (MIMO) antenna for eight-band mobile handsets is designed and implemented. For the MIMO antenna, two hybrid antennas are laid symmetrically and connected by an interconnection tie, thereby enabling complementary operation. The tie affects both the impedance and radiation characteristics of each antenna. Further, printed circuit board (PCB) embedded type is applied to the antenna design. To verify the results of this study, we designed eight bands-LTE class 12, 13, and 14, CDMA, GSM900, DCS1800, PCS, and WCDMA-and implemented them on a bare board the same size as the real board of a handset. The voltage standing wave ratio (VSWR) is within 3:1 over the entire design band. Antenna isolation is less than -15 dB at the lower band, and -12 dB at the WCDMA band. Envelope correlation coefficient (ECC) of 0.0002-0.05 is obtained for all bands. The average gain and efficiency are measured to range from -4.69 dBi to -2.88 dBi and 33.99% to 51.5% for antenna 1, and -4.74 dBi to -2.97 dBi and 33.45% to 50.49% for antenna 2, respectively.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.2045-2049
• /
• 2018

An antenna arrays for a satellite navigation systems require more antenna elements to mitigate multiple jamming signals. In order to maintain the small array size while increasing the number of antenna elements, miniaturization technique is essential for antenna design. In this work, an electrically small circular microstrip patch antenna with a 3 dB hybrid coupler is designed as an element antenna, where the 3 dB hybrid coupler can yield the circularly polarized radiation characteristic. The miniaturized element antenna typically has too large capacitance in GPS L1 and GLONASS G1 bands, making it difficult to match with a single stand-alone non-Foster matching circuit (NFMC) in a stable state. Therefore, we propose a new matching technique, referred to as the hybrid matching method, which consists of a NFMC and a passive circuit. This passive tuning circuit manages reactance of antenna elements at an appropriate capacitance without a pole in the operating frequency range. The antenna array is fabricated, and the measured results show a reflection coefficient of less than -10 dB and an isolation of greater than 50 dB. In addition, peak gain of the proposed antenna is increased by 22.3 dB compared to the antenna without the hybrid matching network.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.10
• /
• pp.21-26
• /
• 2002

In this paper, a hybrid slot antenna is designed and fabricated for wireless LAN at 5.8㎓ band. The hybrid slot antenna is consisted of the inductively-fed slot and capacitively-fed slot. To obtain wide bandwidth, the inductively-fed slot is designed at 5.3㎓ and the capacitively-fed slot is designed at 5.8㎓ Important parameters in the design are slot width and CPW length. The hybrid slot antenna is simulated by using Ensemble 6.0. The measured results of this antenna are compared with its simulated results. The resonant frequency of fabricated hybrid slot antenna is 5.8㎓, the bandwidth for VSWR＜1.5 is 28% and the gain is 5 ㏈i. The 3-㏈ beamwidths in E-plane and H-plane are 60°and 44°, respectively.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.4
• /
• pp.65-70
• /
• 2011

In this paper, we designed and implemented a PIFA(Planer Inverted F Antenna) and IFA(Inverted F Antenna) hybrid antenna for the data communication terminal such as smart phone. Studied hybrid antenna has multi-band characteristics by the simultaneous operation both PIFA and IFA under a feeding structure. VSWR measurement of implemented antenna was satisfied 3:1 over GSM900/USPCS/WCDMA band. Measured average gains and efficiencies were -2.19~-3.63 dBi and 43.31~60.33 % for the GSM900 band, and -2.16~-10.67 dBi and 8.56~60.78 % for the USPCS/WCDMA band.

• ETRI Journal
• /
• v.31 no.5
• /
• pp.616-618
• /
• 2009

In this letter, a novel hybrid planar inverted-F antenna (PIFA) with a T-shaped slot on the ground plane is proposed. The loop structure formed by the feed line and shorting pin can be operated as a series and shunt inductance for the PIFA and the T-shaped slot antenna, respectively. The PIFA operates at a frequency of 1.75 GHz, while the T-shaped slot on the ground plane operates at 2.4 GHz by the same voltage feeding source. The height of the PIFA is 6.5 mm, and the size of an upper patch is designed to be 30 mm${\times}$16 mm. The measured relative impedance bandwidth of the PIFA and the T-shaped slot are about 12% and 21%, respectively. In addition, good antenna performance was achieved.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.4
• /
• pp.165-169
• /
• 2011

In recent years mobile phone handset terminal has tended to have additional various functions and slim and light weight, and its internal space is getting smaller and narrower. According to complex parts, small and narrow inner space is caused not sufficient bandwidth and lower impedance. Moreover, additional polarization loss by the surrounding parts produces is lower effectiveness and increases difficulties for getting the antenna gain. For IFA is low profile structure based on the ILA(Inverted L Antenna) which is transformed from the monopole antenna. While this antenna has lots of advantages in internal antenna of mobile phone, it has some disadvantage of reduced bandwidth and gains compared with monopole antenna. In this paper, propose vlade hybrid antenna use for the coupling structure.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.183-185
• /
• 2010

A 2.4 GHz dual-polarized antenna for a Doppler radar is studied. The proposed dual-polarized antenna using a stacked annular ring patch with two co-centric gap-coupled feed lines and a $90^{\circ}$ hybrid exhibits fairly good performance of 22 dB isolation at a center frequency of 2.4 GHz. Using a $90^{\circ}$ hybrid, a right-handed circular polarization for the transmitter and a left-handed circular polarization for the receiver are implemented. The gain of the designed antenna is about 0 dBi over operating frequencies. The antenna size including a ground plane is only $40{\times}40\;mm^2$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.3
• /
• pp.248-256
• /
• 2015

In this paper, a hybrid MIMO antenna for the metal phone with auxiliary slot for 4th generation mobile communication is designed and implemented. Auxiliary slot locates on the rear metal cover of the phone, and handles for LTE class 40 band. The auxiliary slot operates hybrid with a monopole antenna. Studied antenna satisfies under VSWR 3:1 for LTE class 13/ LTE class 14/ CDMA/ GSM/ DCS/ PCS/ W-CDMA/ LTE class 40 bands. ECC(Envelope Correlation Coefficient) value for MIMO characteristic is less than 0.2 over the whole design bands. Average gains and antenna efficiencies measured by MTG anechoic chamber were -5.57~-1.45 dBi and 27.75~71.6 %, respectively.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.3
• /
• pp.200-205
• /
• 2014

In this paper, 5.8GHz band $4{\times}4$ Butler matrix is designed using easily accessible commercial $90^{\circ}$ hybrid coupler and semirigid coaxial cable as a transmission line. This Butler matrix is very flexible to changes of antenna system specification like a frequency band because $90^{\circ}$ hybrid coupler changing is all to do. The result of design is the distance of $2{\times}2$ array antenna element is $\sqrt{2}{\lambda}/4$, the 4 beam directions are diagonal of array antenna and phase shifter is not necessary. The beam width is roughly $25^{\circ}$ narrower because of array antenna geometry and the side lobe is about 10dB higher partially than theoretical beam pattern. But the overall beam pattern is similar with theoretical beam. This Butler matrix can be applied to switching beam antenna of 5.8GHz band Wi-Fi and WAVE system.