• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.1
• /
• pp.117-123
• /
• 2003

In a bi-fuel engine using gasoline and LPG fuel, with the current ignition timing for gasoline being used, the effective performance could not be taken in LPG fuel supply mode. The ignition timing in LPG fuel mode must be advanced much more than that of gasoline mode for the compensation of its lower flame speed, due to engine torque drop. This study aims to develop the control system for ignition spark timing conversion which is composed of hardwares and control algorithm for gasoline/LPG engine. We propose the control system which can advance the ignition spark timing in LPG fuel mode more than used in gasoline fuel mode. The advance of ignition timing is achieved by change of the ignition dwell time of coil igniter. The engine torque and F/E(Fuel-Economy) in LPG fuel mode are measured to evaluate the difference of engine performance between before and alter changing ignition spark timings. The engine torque and F/E are increased respectively, which proves the developed control system is effective so much for gasoline and LPG bi-fuel engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.93-100
• /
• 2009

Intake/exhaust valve timing and exhaust cam lift were changed to control the internal exhaust gas recirculation (IEGR) and combustion phase of homogeneous charge compression ignition (HCCI) engine. To measure the IEGR rate, in-cylinder gas was sampled during from intake valve close to before ignition start. The lower exhaust cam made shorter valve event than higher exhaust cam and made IEGR increase because of trapping the exhaust gas. IEGR rate was more affected by exhaust valve timing than intake valve timing and increased as exhaust valve timing advanced. In-cylinder pressure was increased near top dead center due to early close of exhaust valve. Ignition timing was more affected by intake valve timing than exhaust valve timing in case of exhaust valve lift 8.4 mm, while ignition timing was affected by both intake and exhaust valve timing in case of exhaust valve 2.5 mm. Burn duration with exhaust valve lift 2.5 mm was longer than other case due to higher IEGR rate. The fuel conversion efficiency with higher exhaust valve lift was higher than that with lower exhaust valve lift. The late exhaust and intake maximum open point (MOP) made the fuel conversion efficiency improve.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.3
• /
• pp.39-47
• /
• 2011

In a bi-fuel engine using gasoline and LPG fuel, with the current ignition timing for gasoline being used, the optimum performance could not be taken in LPG fuel supply mode. The ignition timing in LPG fuel mode must be advanced much more than that of gasoline mode for the compensation of its higher ignition temperature. The purpose of this study is to investigate how the ignition spark timing conversion influences the engine performance of LPG/Gasoline Bi-Fuel engine. In order to investigate the engine performance during combustion, engine performance are sampled by data acquisition system, for example cylinder pressure, pressure rise rate and heat release rate, while change of the rpm(1500, 2000, 2500) and the ignition timing advance($5^{\circ}$, $10^{\circ}$, $15^{\circ}$, $20^{\circ}$). As the result, between 1500rpm, 2000rpm and 2500rpm, the cylinder pressure and pressure rise rate was increased when the spark ignition was advanced but pressure rise rate at $20^{\circ}$ was smaller value.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.61-67
• /
• 1992

The ignition timing feedback control system was studied to enhance the engine power and to reduce the fuel consumption by optimizing the spark timing. The signal of a piezo-electric vibration transducer attached to the engine block was compared with that of a pressure transducer in order to determine the knock intensity. With the result of comparison the ignition timing feedback control system which detect the knock and correct the spark timing was set up. The ignition could be more advaced with this control system than the existing system without the continuous knocking, therefore the engine torque was increased.

• Journal of Industrial Technology
• /
• v.26 no.A
• /
• pp.39-46
• /
• 2006

As an automobile fuel, LPG has many environmental advantages compared to gasoline or diesel. However, current LPG engine which is provided with LPG fuel as gas form has lower power and worse fuel efficiency than gasoline engine. These problems of low power and bad fuel efficiency come from lower volumetric efficiency. Also there is a new rising problem of high failure ratio in an engine emission test. Although there are many factors which affect engine performance of exhaust gas emission, one believes that the fact that ECM of gasoline engine is used for LPG engine when retrofitting gasoline engine to LPG engine is one of the main problems, which lower engine power and emit more noxious gas due to wrong ignition timing. To solve these problems, one studied the effects of ignition timing on the exhaust gas to find out the optimum condition of ignition timing. The experimental results show that noxious exhaust gas is reduced and engine power is increased if the optimum control of ignition timing is applied in accordance to the revolution speed of engine.

• Journal of Energy Engineering
• /
• v.19 no.1
• /
• pp.32-38
• /
• 2010

The objective of the research was to study the effects a Miller cycle. The engine was dedicated to natural gas usage by modifying pistons, fuel system and ignition systems. The engine was installed on a dynamometer and attached with various sensors and controllers. Intake valve timing, engine speed, load, injection timing and ignition timing are main parameters. Miller Cycle without supercharging can increase brake thermal efficiency 1.08% and reduce brake specific fuel consumption 4.58%. The injection timing must be synchronous with valve timing, speed and load to control the performances, emissions and knock margin. Throughout these tested speeds, original camshaft is recommended to obtain high volumetric efficiency.

• Journal of Energy Engineering
• /
• v.17 no.4
• /
• pp.198-203
• /
• 2008

The objective of the research was to study the effects of Miller cycle in a modified using diesel engine. The engine was dedicated to natural gas usage by modifying pistons, fuel system and ignition systems. The engine was installed on a dynamometer and attached with various sensors and controllers. Intake valve timing, engine speed, load, injection timing and ignition timing are main parameters. The results of engine performances and emissions are present in form of graphs. Miller Cycle without supercharging can increase brake thermal efficiency and reduce brake specific fuel consumption. The injection timing must be synchronous with valve timing, speed and load to control the performances, emissions and knock margin. Throughout these tested speeds, original camshaft is recommended to obtain high volumetric efficiency. Retard ignition timing can reduce $NO_x$ emissions while maintaining high efficiency.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.5
• /
• pp.61-68
• /
• 1992

Knock phenomenon is an abnormal combustion originated from autoignition of unburned gas in the end-gas region during the later stage of combustion process and it accompanys a high pitched metallic noise. Engine Knock is accompanied with a vibration of engine cylinder and when it is severe, it can cause major engine demage. Engine Knock is characterized in terms of knock crank angle, knock pressure, pressure jump and knock intensity. In this study, a 4-cylinder spark ignition engine was used for experiment and eighty consecutive cycles were analyzed statistically. The purpose of this study is to characterize spark ignition engine knock as a function of ignition timing and fuel research octane number. The result of this study can be summerized as follows. Knock occurrence angle approached TDC as ignition timing is advanced. Pressure and knock intensity gradually increased as spark timing is advanced. Mean knock occurence angle gradually approached TDC as fuel research octane number is decreased for identical spark timing. Knock intensity increased linearly as RON is decreased.

• Journal of Power System Engineering
• /
• v.8 no.3
• /
• pp.5-10
• /
• 2004

This work deals with a controlled auto-ignition (CAI) single cylinder gasoline engine, focusing on the extension of operating conditions. In order to keep a homogeneous air-fuel mixing, the fuel injector is water-cooled by a specially designed coolant passage. Investigated are the engine emission characteristics under the wide range of operating conditions such as 40 in the air-fuel ratio, 1000 to 1800 rpm in the engine speed, $150\;to\;180^{\circ}C$ in the inlet-air temperature, and $80^{\circ}$ BTDC to $20^{\circ}$ ATDC in the injection timing. A controlled auto-ignition gasoline engine which has the ultra lean-burn with self-ignition of gasoline fuel can be achieved by heating inlet air. It can be achieved that the emission concentrations of carbon monoxide, hydrocarbons and nitrogen oxides had been significantly reduced by CAI combustion compared with conventional spark ignition engine.

• Journal of Biosystems Engineering
• /
• v.12 no.1
• /
• pp.45-52
• /
• 1987

In order to improve the thermal efficiency of an internal combustion engine, various ignition timing control systems were examined and the best one was chosen. The parts used for the systems were a microcomputer system with DAS, 8 bit output port (D-FLIP FLOP), three types of isolation circuit, two types of ignition timing pulse generator, three types of switching circuit and two types of high voltage ignition circuit. Most systems did not operate well due to the effects of electromagnetic waves and surge currents occurring when the ignition began or ended with resulting high voltage. The best ignition timing control system was found to be the combination of (microcomputer system)-(ignition timing pulse generator using step motor position control pick-up)-(switching circuit using TR logic)-(high voltage ignition circuit using CDI).