• Fashion & Textile Research Journal
• /
• v.22 no.3
• /
• pp.386-398
• /
• 2020

This study compared dip-coating and in situ polymerization methods for the development of nanofiber-based E-textile using polypyrrole. Nanofiber webs were fabricated by electrospinning an aqueous poly (vinyl alcohol) (PVA) solution. Subsequently, the PVA nanofiber web underwent thermal treatment to improve water resistance. Dip-coating and in situ polymerization methods were used to deposit polypyrrole on the surfaces of the nanofiber web. An FE-SEM analysis was also conducted to examine specimen surface characteristics along with EDS and FT-IR that analyzed the chemical bonding between polypyrrole and specimens. The line resistance and sheet resistance of the treated specimens were measured. Finally, an electrocardiogram (ECG) was measured with textile sensors made of the polypyrrole-deposited PVA nanofiber webs. The polypyrrole-deposited PVA nanofiber webs fabricated by dip-coating dissolved in the dip-coating solution and indicated damage to the nanofibers. However, in the case of in situ polymerization, polypyrrole nanoparticles were deposited on the surface and inter-web structure of the PVA nanofiber web. The resistance measurements indicated that polypyrrole-deposited PVA nanofiber webs fabricated by in situ polymerization with an average sheet resistance of 5.3 k(Ω/□). Polypyrrole-deposited PVA nanofiber webs fabricated by dip-coating showed an average sheet resistance of 57.3 k(Ω/□). Polypyrrole-deposited PVA nanofibers fabricated by in situ polymerization showed a lower line and sheet resistance; in addition, they detected the electrical activity of the heart during ECG measurements. The electrodes made from polypyrrole-deposited PVA nanofiber webs by in situ polymerization showed the best performance for sensing ECG signals among the evaluated specimens.

• Macromolecular Research
• /
• v.12 no.1
• /
• pp.85-93
• /
• 2004

We have prepared poly(ethylene terephthalate) (PET) nanocomposites filled with two different types of fumed silicas, hydrophilic (FS) and hydrophobic (MFS) silicas of 7-nm diameter, by in situ polymerization. We then investigated the morphological changes, rheological properties, crystallization behavior, and mechanical properties of the PET nanocomposites. Transmission electron microscopy (TEM) images indicate that the dispersibility of the fumed silica was improved effectively by in situ polymerization; in particular, MFS had better dispersibility than FS on the non-polar PET polymer. The crystallization behavior of the nanocomposites revealed a peculiar tendency: all the fillers acted as retarding agents for the crystallization of the PET nanocomposites. The incorporation of fumed silicas increased the intrinsic viscosities (IV) of the PET matrix, and the strong particleparticle interactions of the filler led to an increased melt viscosity. Additionally, the mechanical properties, toughness, and modules of the nano-composites all increased, even at low filler content.

• Textile Coloration and Finishing
• /
• v.15 no.3
• /
• pp.127-131
• /
• 2003

Acrylonitrile(AN) was solution-polymerized in dimethyl sulfoxide(DMSO) and tertiary butyl alcohol(TBA) at 30, 40, $50^\circ{C}$ using a low temperature initiator, 2,2'-azobis(2,4-dimethylvaleronitrile) (ADMVN). The low temperature polymerization using ADMVN, DMSO, and TBA is to be successful in obtaining high molecular weight polyacrylonitrile(PAN) with less branches by solution polymerization. Throug a polymerization of AN in DMSO at $30^\circ{C}$, PAN having viscosity-average molecular weight$(M_v)$ of 931,000 was obtained. And then, during AN solution polymerization in DMSO and TBA using a cosolvent system the in-situ formation of microfibrillar structure has been discovered at the cosolvent composition of 24/1$(V_{DMSO}/V_{TBA})$. The simultaneous process of gelation and phase separation of long chain molecules may explain the in-situ formation of PAN fibers during polymerization.

• Elastomers and Composites
• /
• v.33 no.4
• /
• pp.255-266
• /
• 1998

One-step continuous reactive blend with EPDM is investigated using a modular intermeshing corotating twin screw extruder This was performed via anionic polymerization mechanism. Mechanical properties were characterized and compared with mechanical blends.

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.902-906
• /
• 1999

Electrically conducting composite films were prepared by a vapor phase in situ polymerization of pyrrole in the methyl cellulose film containing a copper(II) perchlorate. Methylcellulose had high affinity to pyrrole and was used as a matrix polymer. Conducting polypyrrole was embedded in the methylcellulose film forming a conducting network and the conductivity of the composite films ranged $10^{-1}$ to $10^{-7}S/cm$. The conductivities of conducting composite films were dependent on the nature of the matrix polymers, concentration of oxidant and polymerization time. In situ polymerization of pyrrole was observed in the matrix polymer and confirmed by UV-vis spectra. From the results of the thermogravimetric analysis, the chemical oxidative polymerization of pyrrole in the matrix polymers did not give any negative effects on the thermal stability of the composite films. Electron micrograph of composites indicated good penetration of PPy in the matrix polymer. DMA suggested a certain degree of incompatibility of the polypyrrole in the composites.

• Macromolecular Research
• /
• v.14 no.3
• /
• pp.312-317
• /
• 2006

In the preparation of a polyacrylonitrile (PAN)/sodium montmorillonite (Na-MMT) nanocomposite via an in-situ polymerization method, macroazoinitiator (MAI) was intercalated in the gallery of Na-MMT to enhance the delamination of silicate layers by intergallery polymerization. The exfoliated fine dispersion observed by X-ray diffraction pattern and transmission electron microscopy, the enhanced tensile storage modulus and the thermal decomposition temperature showed that the intercalated MAI was effective in inducing intergallery polymerization and that a poly(ethylene glycol) block linked to a PAN block improved the dispersion of hydrophilic Na-MMT in the polymer matrix.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.23 no.2
• /
• pp.326-334
• /
• 1999

Polyaniline(PAn)-nylon 6 composite fabrics were prepared by immersing the nylon 6 fabrics in 100% distilled aniline for specified diffusion time and drawn out. Then the excess aniline on the fabric surface was blotted and successive polymerization was initiate by immersing them into oxidant and dopant solution for in situ polymerization of polyaniline. Consequently highly conductive PAn-nylon 6 composite fabrics could be obtained and the conductivity reaches as high as 10-2 S/cm. The maximum conductivity was obtained when the fabric was immersed in 100% aniline at 4$0^{\circ}C$ for 3hours and polymerization was proceeded in 0.25M ammonium peroxydisulfate solution at 5$^{\circ}C$ for 1hour.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.2
• /
• pp.228-235
• /
• 2009

We synthesized glycidyl azide monomer(GAM) as a monomer for polymerization of glycidy azide polymer(GAP) which is a promising energetic prepolymer for a plastic-bonded explosive. Using quantitative real-tim in-situ infrared(in-situ IR) spectroscopy, kinetic study on the cationic ring opening polymerization of GAM was carried out. The reaction rate was obtained from monitoring the change of ether C-O stretching band($1050cm^{-1}$) in series IR spectra. The reaction was in accordance with the first-order reaction law for each of reaction temperature at 100/1 mole ratio of [GAM]/[$BF_3*etherate$]. In the ring opening polymerization of GAM, with ratio of [GAM]/[$BF_3*etherate$] to equal 100/1 at various temperature, the activation parameters obtained from the evaluation of kinetic data were ${\Delta}H^*$=14.34kcal/mol, ${\Delta}S^*=-12.31cal/mol{\cdot}K$ and $E_a$=14.89kcal/mol.

• Design & Manufacturing
• /
• v.17 no.3
• /
• pp.28-33
• /
• 2023

The conventional FRP (Fiber Reinforced Plastic) manufacturing process used thermoset resins for ease of molding but faced the issue of non-recyclability. To address these shortcomings, a new process utilizing thermal plastic resin was developed. However, due to the high viscosity of thermal plastic resin, problems such as fiber deformation and a reduced fiber volume fraction occurred during the high-temperature, high-pressure process. In this study, to overcome the limitations of the conventional process, fiber-reinforced composite materials were manufactured through in-situ polymerization using PLA (Poly L-Lactide) resin in the VA-RTM (Vacuum Assistance Resin Transfer Molding) process. The fiber volume of the produced specimens was calculated, and resin impregnation and porosity were confirmed through optical microscopy. Additionally, molecular weight analysis using GPC (Gel Permission Chromatography) demonstrated improvements over the conventional process and emphasized the essential requirement of temperature control.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.87-90
• /
• 2005

In this study, we have examined the exfoliation behavior of layered clay during in-situ polymeriztion with styrene by using real-time XRD analysis. The 4C1 beam line at the Pohang Accelerator Laboratory (PAL) was used for this study. Different exfoliation behaviors have been shown to depend on the cation exchange capacity (CEC) of clay and the chemical structure of organic modifiers. For 10A-MMT and 15A-MMT having high CEC, no peak shifts were observed on real-time XRD analysis during polymerization. However, 2$\theta$ for 25A-MMT and VDAC-MMT, each having low CEC’s as well as aromatic benzene moieties and vinyl groups, respectively, decreased as polymerization time increased.