• Journal of computational fluids engineering
• /
• v.3 no.1
• /
• pp.100-107
• /
• 1998

A numerical analysis of thermal stress over temperature variations near the crystal-melt interface is carried out for a floating-zone growth of Cadmium Telluride (CdTe). Thermocapillary convection determines crystal-melt interfacial shape and signature of temperature in the crystal. Large temperature gradients near the crystal-melt interface yield excessive thermal stresses in a crystal, which affect the dislocations of the crystal. Based on the assumption that the crystal is elastic and isotropic, thermal stresses in a crystal are computed and the effects of operating conditions are investigated. The results show that the extreme thermal stresses are concentrated near the interface of a crystal and the radial and the tangential stresses are the dominant ones. Concentrated heating profile increases the stresses within the crystal, otherwise, the pulling rate decreases the stresses.

• Journal of Biosystems Engineering
• /
• v.26 no.2
• /
• pp.123-130
• /
• 2001

The research described in this paper was aimed toward improving the understanding of the interaction of tire inflation pressure and the soil-tire interface stresses. A three-directional stress transducer was developed to measure stress distribution on undertread for a tractor tire. The transducer can directly measure three-directional stresses (normal stress, tangental stress and lateral stress and lateral stress) simultaneously and has both strong structure and high sensitivity, which is not changed by the abrasion of the detecting plate. Measurements of soil-undertread interface stresses were made at tire center on undertread on a 12.4-R24 radial tractor tire opeated at three combinations of a dynamic load (11.8kN) and three inflation pressures (59kPa, 108kPa and 157kPa). These measurements showed that as inflation pressure increased, the soil-undertread interface stresses increased. The results of three stresses comparisons were shown that the peak normal stresses were considerably higher than the tangential peak stresses and the peak lateral stresses.

• Journal of Power System Engineering
• /
• v.14 no.3
• /
• pp.52-57
• /
• 2010

Interlaminar stresses near the free edges of composite laminates have been analyzed considering wall effects. Interface modeling of bonding layer was introduced to explain the wall effect. Using Lekhnitskii stress functions and the principle of complementary virtual work, the interlaminar stresses were obtained, which satisfied the traction free boundary conditions not only at the free edges, but also at the top and bottom surfaces of laminates. The interface modeling provides not singular stresses but concentrated finite interlaminar stresses. The significant amount of reductions of stresses at the free edge are observed compared to the results without interface modeling. The real stress state can be predicted accurately and the results demonstrate the usefulness of the proposed interface modeling for the strength design of composite laminates.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.1
• /
• pp.1-5
• /
• 2015

This paper deals with the residual stresses developed in an epoxy film deposited on Si wafer. First, chemically induced residual stresses due to the volumetric shrinkage in cross-linking resins during polymerization are treated. The curvature measurement method is employed to investigate the residual stresses. Then, thermally induced stresses are investigated along the interface between the epoxy film and Si wafer. The boundary element method is employed to investigate the whole stresses in the film. The singular stress is observed near the interface corner. Such residual stresses are large enough to initiate interface delamination to relieve the residual stresses.

• Advances in Computational Design
• /
• v.4 no.3
• /
• pp.239-250
• /
• 2019

The insertion of femoral implants is the most important phase for surgeons, given the characteristics of the cement during its mixing phase, generating residual stresses of thermal origin that increase the different stresses induced in the bone cement. The aim of our study is to determine the different stresses that affect the cement and more particularly at the cement-implant interface for different temperatures, and to make a comparison with the cement at ambient temperature. It was concluded that, there are a large concentration of stresses in the proximal part of the cement. For normal stresses, the bone cement is affected by stresses of tension and compression due to the effect of polymerization and the contraction of the cement.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.383-388
• /
• 2003

This paper deals with the singular stresses developed in a polymer coating on concrete due to temperature change. The boundary element method is employed to investigate the behavior of interface stresses. Numerical results show that very large stress gradients are present at the interface comer and such stress singularity dominates a very small region relative to layer thickness. Since the exceedingly large stresses at the interface corner cannot be borne by coating materials, local yielding or delamination can occur in the vicinity of free surface.

• Tribology and Lubricants
• /
• v.16 no.4
• /
• pp.289-294
• /
• 2000

This paper present the contact stresses, which considers the shear stress at the cam and follower interface in the direct acting type valve train system of a high speed engine. To determine the contact condition, the normal contact forces are calculated by using the lumped mass dynamic modeling. The line contact is considered between the cam and follower interface. The variations of dynamic stresses are presented as a function of camshaft rotational angle. Also the effects of various design parameters are investigated.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2002.11a
• /
• pp.27-33
• /
• 2002

The residual thermal stresses at the interface corner between the elastic substrate and the viscoelastic thin film due to cooling from cure temperature down to room temperature have been studied. The polymeric thin film was assumed to be thermorheologically simple. The boundary element method was employed to investigate the nature of stresses on the whole interface. Numerical results show that very large stress gradients are present at the interface comer and such stress singularity might lead to edge cracks or delamination.

• Structural Engineering and Mechanics
• /
• v.5 no.6
• /
• pp.705-713
• /
• 1997

The residual thermal stresses at the interface corner between the elastic fiber and the viscoelastic matrix of a two-dimensional unidirectional laminate due to cooling from cure temperature down to room temperature were studied. The matrix material was assumed to be thermorheologically simple. The time-domain boundary element method was employed to investigate the nature of stresses on the interface. Numerical results show that very large stress gradients are present at the interface corner and this stress singularity might lead to local yielding or fiber-matrix debonding.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.1
• /
• pp.35-39
• /
• 2018

This paper deals with the relaxation of singular stresses developed in an epoxy adhesive at high temperature. The interface stresses are analyzed using BEM. The adhesive employed in this study is an epoxy which can be cured at room temperature. The adhesive is assumed to be linearly viscoelastic. First, the distribution of the interface stresses developed in the adhesive layer under the uniform tensile stress has been calculated. The singular stress has been observed near the interface corner. Such singular stresses near the interface corner may cause epoxy layer separated from adherent. Second, the interfacial thermal stress has been investigated. The uniform temperature rise can relieve the stress level developed in the adhesive layer under the external loading, which can be viewed as an advantage of thermal loading. It is also obvious that temperature rise reduces the bonding strength of the adhesive layer. Experimental evaluation is required to assess a trade-off between the advantageous and deleterious effects of temperature.