• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.11
• /
• pp.2512-2520
• /
• 1997

The classes of Reverse Jacket matrix [RJ]$_{N}$ and the corresponding Restclass Reverse Jacket matrix ([RRJ]$_{N}$) are defined;the main property of [RJ]$_{N}$ is that the inverse matrices of them can be obtained very easily and have a special structure. [RJ]$_{N}$ is derived from the weighted hadamard Transform corresponding to hadamard matrix [H]$_{N}$ and a basic symmertric matrix D. the classes of [RJ]$_{2}$ can be used as a generalize Quincunx subsampling matrix and serveral polygonal subsampling matrices. In this paper, we will present in particular the systematical block-wise extending-method for {RJ]$_{N}$. We have deduced a new orthorgonal matrix $M_{1}$.mem.[RRJ]$_{N}$ from a nonorthogonal matrix $M_{O}$.mem.[RJ]$_{N}$. These matrices can be used to develop efficient algorithms in IMT2000 signal processing, multidimensional subsampling, spectrum analyzers, and signal screamblers, as well as in speech and image signal processing.gnal processing.g.

• Journal of Fashion Business
• /
• v.11 no.4
• /
• pp.120-134
• /
• 2007

The usage of basic bodice blocks at men's apparel companies is investigated and the domestic and international men's upper bodice blocks are compared to find directions of research on development of bodice basic blocks. The following conclusions are found in this study. 1. The survey shows that basic bodice blocks are not used at men's apparel companies although all the respondents have good knowledge on bodice basic blocks. They responded that basic bodice blocks for representative body figures of each age category or of each country would help comparative studies on domestic and international basic bodice blocks and development of exporting apparel products. Also, they expected the utilization of men's basic bodice blocks both as education materials and in studies of design, of body figures, and of basic blocks for industry. 2. The comparative study on men's bodice blocks shows that waist circumference, hip circumference, neck circumference, height, and shoulder length, in addition to the minimal essential size items such as chest circumference and center back length, are used in most basic bodice blocks. The size formulae of each basic block are compared to find how the sizes are determined. For center back length, either measured back length or a certain proportion of height is used. For front and back interscyes, chest circumference is used in most basic bodice blocks. Either measured size, or a certain proportion of height or chest circumference is used for back height. The averaged ease allowances of basic bodice blocks are 3.2 cm for chest circumference, 10.8 cm for waist circumference, 1.2 cm for front interscye, 0.1 cm for back interscye, 0.2cm for shoulder length, and 0 cm for center back length. However, body blocks for different types of clothes have different ease allowances. Shirt basic blocks have ease allowances of 6.1 cm for chest circumference, 13.7 cm for waist circumference, 1.4 cm for front interscye, 0.6 cm for back interscye, 1.2 cm for shoulder length, and 1.8 cm for center back length. On the other hand, jacket basic blocks have ease allowances of 8.8 cm for chest circumference, 16 cm for waist circumference, 1.1 cm for front interscye, 1.4 cm for back interscye, 1.1 cm for shoulder length, and 0.8 cm for center back length.

• Journal of the Korean Society of Costume
• /
• v.56 no.4 s.103
• /
• pp.48-64
• /
• 2006

The purpose of the study was to demonstrate how to recreate spencer jacket in the empire style in an attempt to apply this historic style to theatrical costumes and other high fashion items in modern times. The study was carried out through 2 steps. (1)Block patterns of spencer jacket of its basic design were developed through draping based on the design characteristics mentioned above. (2)Spencer jackets of three designs, which were the typical designs of each category have been made of velvet to find out more specific structural characteristics. The structural characteristics of Spencer jacket in draping were as follows: (1)Jacket length position was suitable 9cm below body's bust line and neckline should be enlarged front & side neck point 2cm, back neck point 1.5cm. (2)Cut out the front bodice after CF line moved 1cm outwards and bust dart amount should not exceed 2-3cm. Shoulder point moved inwards. (3)Side back grain line was parallel to princess line of the back bodice. Add 0.5cm ease to the under arm of the front and side bark bodice, it was good for the activity of arm. (4)Armhole line was trued as maintaining to across back width 14-15cm at least. Shoulder line was to connect from the point 2cm depart shoulder point along armhole line to point 2cm side neck point along neck line. (5)Sleeve length was suitable 70cm, cut out the bias direction to move forwards the grain line from shoulder point. Puff position was good from the 2cm depart shoulder point to shoulder line.

• Journal of the Korea Convergence Society
• /
• v.12 no.2
• /
• pp.185-191
• /
• 2021

The characteristics of the foundry sand were analyzed for water jacket core required to prevent structural deformation from the heat generated in the cylinder bore during the casting of the cylinder block of an automobile. The sand core tensile strength tester, AFS-GFN, and optical microscope were used to evaluate the its properties. If the SiO2 content is high in the foundry sand, the dimensional defects and veining defects occur due to high temperature expansion. Also, if it is too low, the core breakage, porosities, chemical burn-on defects occur. The particle size index and grain shape influenced the core strength and resin consumption, resulting in fluctuations in defect types. The higher the alkalinity of the dried sand, the lower the core strength. And the more basic, the lower the core strength. At the resin content of 1.6~1.8%, the increase in core strength after 1 hour curing was approximately at its maximum.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.6
• /
• pp.999-1011
• /
• 2008

To most of the students studying fashion related major, the graduation fashion show is a big challenge. They have to put together all they learn and show what they can do to their future employers. They design, pattern work, and make up garments for the show all by themselves. Unfortunately. while they make up their garments, they usually don't Dow exactly body measurements of the models. So quite often they have to alter their art works up to the last minute of the fashion show opening. Sometimes such unadequate work process ruins their work. The purpose of this study is to suggest block patterns of Korean fashion models measurements for basic items, such as jacket and pants for male models and torso length block pattern, skirt and pants for female models. 20 male and 20 female professional models were measured. The block patterns were based on their measurements. After the first fitting test, patterns were corrected by their body characteristic. For both male and female models, it was found desirable to fix the shoulder width and make an adjustment to the patterns with a deviation of width and girth items. In case of the resultant patterns the satisfaction was made better. Model sizes proposed in this study are considered closer to the size of average models, since they were based on A-grade models who are currently working in Korea. The resultant patterns can be produced by simply making a slight adjustment to the width of the proposed pattern in this study.