• Journal of Technologic Dentistry
• /
• v.18 no.1
• /
• pp.117-127
• /
• 1996

This study was aimed to help the construction of esthetic dental prosthesis by investigation of the factors affecting on the atterition position and attrition angle of maxillary lateral incisors. Therefore 197 complete cast of maxillary and mandibualar extracted form the student of K. college were subjected for this study, and result throught the study are as follows. 1. None attrite rate of the maxiilary right lateral incisors was about 16.2% and that of the maxillary left lateral incisors was about 32.4% of examined teeth. 2. Throught mesiodistal attrition area 1) It showed that right lateral incisors was the most frequence in attrition of mesial area of incisal edge, and left lateral incisors was the most frequence in attrition of mesial and mid area of incisal edge. 2) It showed that square type arch was more frequence in attrition of all incisal edge, and ovoid type arch was more frequence in the attrition of mid area of incisal edge, and ovoid type arch was more frequence in the attrition of mid area of incisal edge, and taper type arch was more frequence in the attrition of mesial area of incisal edge than it of average frequence of right lateral incisors, by dental arch type. 3) It showed that square type arch was more frequence in the attrition of all area and mid area of incisal edge, and ovoid type arch was more frequence in the attrition of mid area of incisal edge, and taper type arch was more frequence in the attrition of mesial and distal area of incisal edge than it of average frequence of left lateral incisal, by dental arch type. 4) Sex, vertical overlap, horizontal overlap, incisal guide angle, did not affect significantly to throughout mesiodistal attrition, statistically 3. Throughout labiolingual attrition quantity. 1) It showed that throughout labiolingual attrition quantity was more attrition in order of taper type arch < ovoid type arch < square type arch, by dental arch type. 2) It showed that throughout labiolingual attrition qauntity was more attrition when the length of horizontal overlap is shorter than it of other, by horizontal overlap. 3) Throughout labiolingual attrition quantity of right lateral incisors showed that male was more attrition than it of female. 4) Vertical overlap, incisal guide angle, sex on left lateral incisors did not affect significantly to throughout labiolingual attrition, statistically. 4. Attrition angle 1) It showed that average attrition anlge of right lateral incisors were $30{\pm}13.02$ degree, and it of left lateral incisors were $26{\pm}13.37$ degree. 2) It showed that taper type arch have a bigger attrition angle than it of average of lateral incisors, and square tape arch have a smaller attrition angle than it of average of lateral incisors, by dental arch type. 3) It showed that horizontal overlap of 2.1mm above have a bigger attrition angle than it of average, by horizontal overlap. 4) It showed that female have a bigger attrition angle it of male, by sex.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.12
• /
• pp.43-49
• /
• 2004

In this paper, we have designed a mode size converter to reduce coupling loss between super-high delta silica optical waveguides and single mode fibers. The new mode size converter has three design aspects; periodically segmented taper waveguide for minimal size, lateral taper waveguide for simple fabrication, and surrounding trenches to improve coupling loss. In the optimal mode size converter design, coupling loss is 0.33dB/point without trenches and 0.2dB/point with trenches.

• Restorative Dentistry and Endodontics
• /
• v.30 no.2
• /
• pp.95-101
• /
• 2005

The aim of this study was to evaluate the microleakage of teeth according to root canal preparation with & without apical enlargement in various size of apical foramen. 60 extracted one canal roots were cross-cutted at 5 mm from root apex and divided into two groups according to their apical foramen size of large (L) and small (S). Each group was subdivided into two groups accordance with their cross-sectional configuration at 5 mm from apex, round (R) and ovoid (O); SR Group, SO Group LR Group, LO Group. Each group was shaped in .02 taper by Quantec series Nickel-Titanium (NiTi) rotary file, obturated by lateral condensation method. Leakage was measured using a fluid transport model under 40 $cmH_2O$ pressure. After the leakage test, blocks which had showed the leakage retreated with .04 taper and ,06 taper and evaluated the degree of fluid filtration in each group. The data was analysed statistically using chi-square test and fisher's exact test. The results obtained were as follows : 1. Significant difference in leakage was found in groups which had different apical foramen size in .02 taper instrumentation (p < 0.05), but not in .04 taper instrumentation (p > 0.05) 2. The difference in microleakage according to the shape of canal was not evident at 5 mm from apex (p > 0.05). 3. There was correlation between .02 taper instrumentation and .04 taper instrumentation in LR group, LO group (p < 0.05).

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.770-773
• /
• 2021

In this paper, the retention characteristics of 3D NAND flash memory applied with tapering and ferroelectric (HfO₂) structure were analyzed after programming operation. Electrons trapped in nitride are affected by lateral charge migration over time. It was confirmed that more lateral charge migration occurred in the channel thickened by tapering of the trapped electrons. In addition, the Oxide-Nitride-Ferroelectric (ONF) structure has better lateral charge migration due to polarization, so the change in threshold voltage (V_th) is reduced compared to the Oxide-Nitride-Oxide (ONO) structure.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.22-27
• /
• 2004

In this paper, we designed a mode size converter to reduce coupling loss between optical waveguide and single mode fiber. The proposed mode converter is composed of periodically segmented tapered waveguide to achieve small size and easy fabrication. For the optimally designed mode size converter at 1550nm, the taper length is 500(equation omitted), the segmentation period 5ß:, the waveguide width of fiber contact section 1.3ß:, and duty cycle 0.95. The coupling loss of the optimized mode size converter is 0.33㏈/point, which is 1.27㏈/point lower than that without the mode size converter.

• Restorative Dentistry and Endodontics
• /
• v.27 no.5
• /
• pp.521-529
• /
• 2002

The purpose of this study was to compare the shaping time of two shaping methods and the leakage of three different obturation techniques. Ninty three canaled human molar teeth were used, which were randomly divided into two groups of forty teeth each and ten control teeth. After working length determination, the one group was prepared crown-down technique using rotary root canal instruments of GT rotary files .12/20, .10/20, .08/20 and .06/20 taper(Maillefer Instrument SA. Switzerland). The other group was instrumented with Gates Glidden burs(#1, #2, and #3) to coronal preparation and GT rotary files .08/20 and .06/30 taper to apical preparation. Shaping time was measured. After root canals were instrumented, they were divided to three subgroups and obturated as follows : Subgroup 1, obturated with single cone method Subgroup 2, obturated with lateral condensation : Subgroup 3, obturated with continuous wave technique. Three subgroups were obturated using non-standardized gutta-percha cone(Diadent, Korea, .06 or .08 taper) and AH-26(Dentsply DeTrey, Germany) as a root canal cement. Ten unobturated teeth served as positive and negative controls. After immersion in 2% methylene blue solution for 1 month, the teeth were washed during 24h. The teeth were demineralized in 10% nitric acid and dehydrated by immersion in 80, 90 and 100% ethyl alcohol. The teeth were finally cleared and stored in 100% methylsalicylate, and apical dye penetration was evaluated under stereomicroscope(Leica M420, LC, U.S.A)at $\times$8.75 magnification. Liner measurement of dye penetration was assessed with the use of digitalized image analysing system (analySIS, GmbH, Germany) The data were analysed statistically using independent T-test and Two-way ANOVA and Tukey test. The result were as follows 1. In canal prepared with GT$^{TM}$ rotary file, shaphing time taked more than the group of using Gates Glidden drill to coronal preparation without statistical significance (p>0.05) 2. The group of single cone obturation using canal preparation of GT$^{TM}$ rotary files showed significantly more apical leakage than those of lateral condensation and continuous wave technique regardless of shaping method (p<0.05). 3 The group of single cone obturation using canal preparation of GT$^{TM}$ rotary files and Gates Glidden drill showed significantly more apical leakage than those of continuous wave technique regardless of shaping method (p<0.05). 4. Regardless of shaping method, The group of continuous wave obturation showed less apical leakage than those of lateral condensation without statistical significance (p>0.05). 5. The group of single cone obturation using canal preparation of GT$^{TM}$ rotary files and Gates Glidden drill showed more apical leakage than the group of lateral condensation using same shaping method with-out statistical significance (p＞0.05).

• Restorative Dentistry and Endodontics
• /
• v.27 no.3
• /
• pp.277-283
• /
• 2002

The purpose of this study is to evaluate the two warm gutta-percha filling techniques by measuring the weight changes of resin blocks before and after canal filling in ribbon shaped canal. Simulated ribbon shaped root canals in 30 transparent resin blocks were instrumented to #40 using .06 taper Profile. 15 resin blocks were obturated with gutta-percha using cold lateral condensation. Warm lateral condensation using the Endotec II was then accomplished on the same 15 blocks. Another 15 resin blocks were obturated using the System B. All canals were obturated without sealer. The resin blocks were weighed after canal preparation and after each subsequent obturation, and then weight changes of the resin blocks were calculated The results were as follows. 1. Warm lateral condensation using Endotec II and continuous wave of condensation using System B produced a denser obturation of gutta-percha compared with conventional cold lateral condensation (p<0.01). 2. There was no significant difference between warm lateral condensation and continuous wave condensation. In conclusion, the warm gutta-percha condensation techniques like warm lateral condensation and continuous wave condensation can be expected to bring favorable canal obturation results in ribbon shaped canals.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.1
• /
• pp.87-95
• /
• 2000

The two eigenvalues (elastic critical load and natural frequency of lateral vibration) of sinusoidally tapered bats with simply supported ends were determined by the finite element method. For the convenience of structural engineers who are engaged in the structural design or vibration analysis of tapered beam-columns, eigenvalue coefficients were expressed by simple algebraic equations. The validity of each algebraic equation was confirmed by the value of unity for each correlation coefficient. The influence of axial thrust on the lateral vibration frequency was also investigated. For this purpose, the axial thrust was increased successively and the corresponding frequency was calculated. The approximate linear relationship between the axial thrust and the square of the frequency was confirmed lot each of the tapered members.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.2
• /
• pp.61-69
• /
• 2007

In this study, experimental analysis was performed about lateral load capacity and behavior of laterally loaded-bored piles for soil conditions and pile shape, i.e. cylindrical and taper piles. Also, Calibration chamber load tests were performed for cylindrical and taper piles considering the variations of relative densities and restraint stresses. According to the results of chamber tests, it was found that, while both vertical and horizontal stresses affect load-responses and ultimate lateral load capacity of laterally loaded piles, effect of the horizontal stress was larger than that of the vertical stress. Effect of lateral load capacity and behavior was relatively small compared to relative density and stress state of soils surrounding piles, but showed a little difference for soil conditions. From comparison between predicted and measured lateral load capacity, it was observed that predicted results differ significantly from measured results. This is mainly due to the fact that the effect of horizontal stress is not considered in the conventional prediction methods.

• Journal of Advanced Marine Engineering and Technology
• /
• v.8 no.1
• /
• pp.37-48
• /
• 1984

For the designing propulsion shafting of ship, shaft diameters are usually calculated according to the Society's rules and other scantlings such as a shaft length, coupling and taper parts, etc., are decided according to calculated diameters. And then, the torsional vibration, the lateral vibration and shaft alignment should be reviewed to check whether the resonance points of torsional or lateral vibration appear within the normal operating speed range and the shaft alignment is reasonable. If the results of calculations are unsatisfactory, this process should be repeated until the final condition is determined and the process of this work takes much time to carry out. To simplify the above tedious processes, authors have developed a computer program to fulfill the above design processes at once. This program takes aim at reducing the manual calculating work associated with the propulsion shafting of ship. To confirm the availability of developed computer program, several propulsion shaftings which are driven by diesel engines, have been analysed. The results calculated by authors developed computer program show comparatively good agreements with those of the actual propulsion shafting.