• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.32-35
• /
• 2002

The work focuses on the development of a Cu lead-frame with a single-sided adhesive tape for cost reduction and reliability improvement of LOC (lead on chip) package products, which are widely used for the plastic-encapsulation of memory chips. Most of memory chips are assembled by the LOC packaging process where the top surface of the chip is directly attached to the area of the lead-frame with a double-sided adhesive tape. However, since the lower adhesive layer of the double-sided adhesive tape reveals the disparity in the coefficient of thermal expansion from the silicon chip by more than 20 times, it often causes thermal displacement-induced damage of the IC pattern on the active chip surface during the reliability test. So, in order to solve these problems, in the resent work, the double-sided adhesive tape is replaced by a single-sided adhesive tape. The single-sided adhesive tape does net include the lower adhesive layer but instead, uses adhesive materials, which are filled in clear holes of the base film, just for the attachment of the lead-frame to the top surface of the memory chip. Since thermal expansion of the adhesive materials can be accommodated by the base film, memory product packaged using the lead-flame with the single-sided adhesive tape is shown to have much improved reliability. Author allied this invention to the Korea Patent Office for a patent (4-2000-00097-9).

• Korean Journal of Materials Research
• /
• v.19 no.5
• /
• pp.288-292
• /
• 2009

This article shows various factors that influence the thermal-cycling reliability of semiconductor devices utilizing the lead-on-chip (LOC) die attach technique. This work details how the modification of LOC package design as well as the back-grinding and dicing process of semiconductor wafers affect passivation reliability. This work shows that the design of an adhesion tape rather than a plastic package body can play a more important role in determining the passivation reliability. This is due to the fact that the thermal-expansion coefficient of the tape is larger than that of the plastic package body. Present tests also indicate that the ceramic fillers embedded in the plastic package body for mechanical strengthening are not helpful for the improvement of the passivation reliability. Even though the fillers can reduce the thermal-expansion of the plastic package body, microscopic examinations show that they can cause direct damage to the passivation layer. Furthermore, experimental results also illustrate that sawing-induced chipping resulting from the separation of a semiconductor wafer into individual devices might develop into passivation cracks during thermal-cycling. Thus, the proper design of the adhesion tape and the prevention of the sawing-induced chipping should be considered to enhance the passivation reliability in the semiconductor devices using the LOC die attach technique.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.09a
• /
• pp.21-30
• /
• 2002

According the difference of flex substrate, (reel tape), there are three kind assembly types of LCD driver IC is COG, TCP and COF, respectively. The TCP is the maturest in these types for stability of raw material supply and other specification. And TCP is the major assembly type of LCD driver IC and the huge demand from Taiwan's large TFT LCD panel house since this spring. But due to its package structure and the raw material applied in this package, there is some limitation in fine pitch application of this package type, (TCP). So, COF will be very potential in compact and portable application comparison with TCP in the future. There are three kinds assembly methods in COF, one is ACF by using the anisotropic conductive film to connect the copper lead of tape and gold bump of IC, another is eutectic bonding by using the thermo-pressure to joint the copper lead of tape and gold bump of IC, and last is NCP by using non-conductive paste to adhere the copper lead of tape and gold bump of IC. To have a global realization, this paper will briefly review the status of Taiwan's large TFT panel house, the internal driver IC design house, and the back-end assembly house in the beginning. The different material property of raw material, PI tape is also compared in the paper. The more detail of three kinds of COF assembly method will be described and compared in this paper.

• Journal of Mechanical Science and Technology
• /
• v.14 no.2
• /
• pp.251-258
• /
• 2000

Thermal deformation in an electronic package due to thermal strain mismatch is investigated. The warpage and the in-plane deformation of the package after encapsulation is analyzed using the laminated plate theory. An exact solution for the thermal deformation of an electronic package with circular shape is derived. Theoretical results are presented on the effects of the layer geometries and material properties on the thermal deformation. Several applications of the exact solution to electronic packaging product development are illustrated. The applications include lead on chip package, encapsulated chip on board and chip on substrate.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.3
• /
• pp.729-737
• /
• 1994

A three-dimensional finite element model of a 20-pin plastic dual-in-line package(PDIP) plugged into a PCE has been developed by using the finite element code ANSYS. The model has been used for thermal characterization of the package during its normal operation under natural convection cooling. Temperature distributions in the package and PCB are obtained from numerical analysis and compared with experimentally measured data. Various cases are assumed and analyzed to study the effects of package and PCB materials on thermal characteristics of PDIP with and without aluminum heatspreader. Thermal dissipation capability of PDIP is greatly increased due to copper die pad/lead frame and heatspreader. However, thermally induced stresses in the package and fatigue life of chip are improved for PDIP with Alloy 42 die pad/lead frame and no heatspreader. It is also found that the role of PCB on thermal characteristics of PDIP is very imporatant.

• Tribology and Lubricants
• /
• v.21 no.2
• /
• pp.71-76
• /
• 2005

This paper compares of mechanical tensile properties of 6 kinds of copper foil. The beam lead made with copper foil. Different from other package type such as plastic package, Chip Size Package has a reliability problem in beam lead rather than solder joint in board level. A new tensile loading system was developed using voice-coil actuator. The new tensile loading system has a load cell with maximum capacity of 20 N and a non-contact position measuring system based on the principle of capacitance micrometry with 0.1nm resolution for displacement measurement. Strain was calculated from the measured displacement using FE analysis. The comparison of mechanical properties helps designer of package to choose copper for ensuring reliability of beam lead in early stage of semiconductor development.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1995.11a
• /
• pp.3-3
• /
• 1995

Plastic IC encapsulation utilizing lead on chip(LOC) die attach technique allows higher device density per unit package area, and faster current speed and easter leadframe design. Nevertheless, since the top surface of the chip is directly attached to the area of the leadframe with a double-sided adhesive tape in the LOC package, it tends to be easily damaged by the leadframe, leading to limitation in its utilization. In this work, it is detailed how the damage of the chip surface occurs, and it is influenced and improved by the LOC construct.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.1 s.18
• /
• pp.17-22
• /
• 2007

Recent new packages such as MCP(Multi-Chip Package), QDP(Quadratic Die Package) and DDP(Dual Die Package) have stack type configuration. This kind of multi-layer package is thicker than single layer package. So there is need for the low height looping technology in wirebonder to make these packages thinner. There is stiff zone above ball in wirebonder wire which is called HAZ(Heat Affect Zone). When making low height loop (below $80\;{\mu}m$) with traditional forward loop, stiff wire in HAZ(Heat Affected Zone) above ball is bended and weakened. So the traditional forward looping method cannot be applied to low height loop. SSB(stand-off stitch) wire bonding method was applied to many packages which require very low loops. The drawback of SSB method is making frequent errors at making ball, neck damage above ball on lead and the weakness of ball bonding on lead. The alternative looping method is BNL(ball neckless) looping technology which is already applied to some package(DDP, QDP). The advantage of this method is faster in bonding process and making little errors in wire bonding compared with SSB method. This paper presents the result of BNL looping technology applied in assembly house and several issues related to low loop height consistence and BNL zone weakness.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.10
• /
• pp.31-39
• /
• 2004

This paper illustrates the noise characteristics under chip's core operations according to types of packages and modules for DDR DRAM For analyzing this, the impedance profiles and power noises are analyzed with DRAM chips having commercial TSOP package and commercial FBGA package on TSOP-based DIMM and FBGA-based DIMH In controversy with common concepts, we find that the noise-isolation characteristics of FBGA package are more weak and sensitive on transferred noises than those of the TSOP package. In addition, the simulated results show that the decoupling capacitor locations of modules are more important to control the self and transfer noise characteristics than the lead inductance of the packages. Therefore, satisfying the target spec of the noise suppression and isolation can be achieved through the design of power distribution systems only with considering not only the package types but also the whole module system.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.09a
• /
• pp.165-172
• /
• 2003

Wafer-level packaging technology has become established with increase of demands for miniaturizing and realizing lightweight electronic devices evolution. This packaging technology enables the smallest footprint of packaged chip. Various structures and processes has been proposed and manufactured currently, and products taking advantages of wafer-level package come onto the market. The package enables mounting semiconductor chip on print circuit board as is a case with conventional die-level CSP's with BGA solder bumps. Bumping technology is also advancing in both lead-free solder alternative and wafer-level processing such as stencil printing using solder paste. It is known lead-free solder bump formation by stencil printing process tend to form voids in the re-flowed bump. From the result of FEM analysis, it has been found that the strain in solder joints with voids are not always larger than those of without voids. In this paper, characteristics of wafer-level package and effect of void in solder bump on its reliability will be discussed.