• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.245-254
• /
• 2009

Efficiency of landfill liners system is usually evaluated based on leakage rate and mass flux. In this study, composite liner systems including the GCL(geosynthetic clay liner) composite liner, the Subtitle D liner, the Wisconsin NR500 liner, and the recently utilized double composite liner, which is a combination of the GCL composite liner and Subtitle D-type liner, have been examined. The leakage rate through circular and long defects in the geomembrane (GM) of the liner system was analyzed with the aids of analytical and numerical methods. For the mass flux criterion, contaminant transport through defects in the GM of landfill liners can be evaluated based on the calculated leakage rates. The diffusion rate of volatile organic compounds through intact landfill liners was evaluated by performing a one-dimensional numerical model. Cadmium and toluene were adoptted in the analyses as typical inorganic and organic substances, respectively, which will be chemical species encountered during landfill operation. The performance-based evaluation indicates that the double composite liner systems are superior to the other types of liner.

• Food Science and Preservation
• /
• v.5 no.2
• /
• pp.150-153
• /
• 1998

As strait As a result of the quality research of liner boards used for the national-made corrugated boxes for apples, basis weight of each sample passed its tolerance within 4%. We found that KA, WLK, and SC liner boards showed better in relative bursting strength. SC, WLK, KA, and SK performed better in relative compression strength. WLK201 and KA210 were good for the outside liner, and K2200 was adequate for medium and inside liner. we classified WLK and KA liner boards as A grade and others as C grade.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.295-304
• /
• 2010

Performance of a landfill liner is evaluated based on leakage rate and mass flux. In this study, the recently utilized double composite liner system, which consists of a geomembrane (GM), a geosynthetic clay liner (GCL), a GM, and a compacted clay layer (61 or 91.5 cm) is compared with other popular composite liners including the single GCL system, the Subtitle D liner system, and the Wisconsin NR500 liner system. The leakage rate through circular and long defects in the GM of the landfill liners is analyzed using numerical models. For the mass flux criterion, the analyses of inorganic contaminant transport through defects in the GM component of liner systems and diffusion of organic compounds through intact landfill liners are conducted using three- and one-dimensional numerical models, respectively. Cadmium and toluene are used in the analyses as a typical inorganic and organic substance, respectively, which will be chemical species encountered during landfill operation. The comparison shows that the double composite liner systems are superior to the other liner systems according to the performance-based evaluation.

• Journal of Technologic Dentistry
• /
• v.42 no.3
• /
• pp.213-219
• /
• 2020

Purpose: This study aimed to identify the impact of physical surface roughing with a polishing tool onto the pre-sintering yttria-stabilized tetragonal zirconia polycrystals (TZP) core and liner treatment for chemical bonding on the bond strength of TZP core and veneering ceramic. Methods: Overall, 80 specimens were classified into two groups (non-liner, NL; and usingliner, UL ) depending on the use of liner, and these two groups were then subclassified into four groups depending on the polishing tool used. (1) Non-liner groups: NS, non-liner+stone point; NC, non-liner+carbide bur; NP, non-liner+paper cone point; NT, non-liner+silicon point. (2) Using-liner groups: US, using-liner+stone point; UC, using-liner+carbide bur; UP, usingliner+paper cone point; UT, using-liner+silicon point. The pre-sintering surface roughing values and shapes were observed, and after burning up the veneering ceramic, the shear bond strength was measured using a universal testing machine. For significance testing, a one-way analysis of variance and Tukey's multiple comparison test were conducted. An optical microscope was used to observe the fracture plane, and the following results were obtained. Results: Surface roughness NP (4.09±0.51 ㎛) represented a higher value than other groups (p<0.001). In shear bond strength, NS (35.21±1.44 MPa) of the NL group showed the highest bond strength (p<0.001). The UL group did not show a statistically significant difference between groups (p=0.612). Conclusion: Our study findings reveal that the bond strength of TZP core and veneering ceramic was improved by pre-sintering physical surface treatment than by chemical bonding with liner surface treatment.

• Steel and Composite Structures
• /
• v.35 no.2
• /
• pp.171-186
• /
• 2020

This paper aims at providing insights on the use of thermosetting liner for the repair of offshore pipelines exposed to corrosion and leakage. The work which covers both experimental and numerical approaches were aspired due to the high cost of repair for pipelines, limitations of thermoplastic material and limited study of reinforced thermosetting liner. The experiment involves a destruction test called the burst test, carried out on an API 5L X42 carbon steel pipe under four case studies, namely (i) intact pipe, (ii) pipe with corrosion defect, (iii) pipe with corrosion defect and repaired with thermosetting liner and (iv) pipe with leakage and repaired with thermosetting liner. The numerical simulation was developed to first validate the experimental results and later to optimize the design of the thermosetting liner in terms of the number of layers required to restore the original strength of the pipe. The burst test shows an improvement in 23% of the burst capacity for the pipe with corrosion defects, after being repaired with a three-layer thermosetting liner. The parametric studies conducted showed that with an addition of thermosetting layers, the burst capacity improves by an average of 1.85 MPa. In conclusions, the improvement in strength can be further increased with increasing thickness of the thermosetting liner. The thermosetting liner was also determined to fail first inside the host pipe.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.497-504
• /
• 1999

This study presents the physical and engineering characteristics of soil-bentonite admixed liner in I landfill. Main focus was the hydraulic conductivity of compacted soil-bentonite admixed and mechanisms governing low permeable properties of the admixed liner. Laboratory and field tests such as compaction, hydraulic conductivity, density, water content for the soil-bentonite admixed liner were carried out. Quality control criteria for the best construction of the soil-bentonite admixed liner was suggested through laboratory and field test results.

• Korean Journal of Veterinary Service
• /
• v.36 no.4
• /
• pp.273-281
• /
• 2013

This study investigated the effects of the alkaline detergent and acid rinse used for cleaning milking machines on the eight commercially available teatcup liner materials. The sample liners prepared for use in the clean-in-place process were analyzed by ultraviolet spectrophotometer, ion chromatography and liquid chromatography. Among the eight liner materials, the ultraviolet spectra of 3 sample liners were shown to have a similar peak shape after cleaning, but the ultraviolet spectra peak shape of 5 sample liners was noticeably changed. No products were detected by ion chromatography in any of the liner materials used in this study. When the liner materials were only treated with alkaline detergent, some additional peaks were observed using liquid chromatography which indicate the creation of molecular substance and elution from liner materials, however, these peaks disappeared when the liner materials were cleaned with the acid rinse. Therefore, we propose that an acid rinse should be applied, after cleaning the milking machine with the alkaline detergent.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.6
• /
• pp.753-760
• /
• 2007

For protection of the cylinder wall of the ball mill for grinding raw ore. the inner side of the cylinder is covered with rubber liner. The rubber is easily worn down because the rubber relatively soft compared with raw ore. So the rubber liner in the ball mill cylinder must be replaced almost every year and the cost for replacing rubber liner formidable. In this paper, for reducing or excluding the cost of replacing rubber liner the basalt liner is designed. The basalt materials are generally harder than raw ore and the basalt liner in the ball mill does not wear down and so it can be used almost permanently. The concave surfaces are made on the liner of the ball mill and the liner in the cylinder wall plays also the role of raising the steel balls mixed in the raw ore. The section profiles of the concave surface have an important effect on the performance of the ball mill. The deep concave grooves raise the steel balls to high levels and give the large potential energy to the steel balls impacting to the raw ore. But if the concave grooves are too deep. the steel balls raised too high by the concave grooves fly along the parabolic path and reach to the other side of cylinder wall and so the steel balls do not play the roles of grinding the raw ore. The forces acting to a steel ball in a concave groove of the cylinder liner are also analyzed in this paper. The formulas calculating the height and the impact point of the steel ball are introduced and presented. Based to these formulas, the optimum section profiles of the basalt liner are presented.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.49
• /
• pp.237-256
• /
• 2011

A Liner Conference can be defined as "a group of two or more vessel operating carriers which provide international liner services for the carriage of cargo on a particular route or routes within specific geographical limits and which has an agreement or arrangement within the framework of which they operate under uniform or common freight rates and any other agreed conditions with respect to the provisions of the liner services". This study reviews maritime transport policy regarding liner conference and the changes in the liner market over the decades. Liner shipping industry has long been protected from competition by block exemption. The repeal of the block exemption for liner conferences and the abolition of any special EC antitrust regime for the shipping industry marks an important step in European maritime competition policy. This article examines the origins and the rationale of the EC antitrust immunity granted so far th the shipping industry and explains the causes of this historic changes. The abolition of Regulation 4056/86 and of the EU commitment to the UN Code of Conduct marks an historical evolution in international maritime policy, which will have an influence far beyond the EU.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.31-38
• /
• 2006

Cylinder liner rotation is a new concept for reducing piston assembly friction in the internal combustion engine. The purpose of cylinder liner rotation is to reduce the occurrence of boundary and mixed lubrication friction in the piston assembly. This paper reports the results of experiments to quantify the potential of the rotating liner engine. A GM Quad-4 SI engine was converted to single cylinder operation and modified for cylinder liner rotation. The hot motoring method was used to compare the friction loss between the baseline engine and the rotating liner engine. Additionally, tear-down tests were used to measure the contribution of each engine component to the total friction torque. The cycle-averaged motoring torque of the RLE represents a $23\~31\%$ friction reduction compared to the baseline engine for hot motoring tests. Through tear down tests, it was found that the piston assembly friction of the baseline engine is reduced from $90\%$ at 1200 rpm to $71\%$ at 2000 rpm through liner rotation.