• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.2
• /
• pp.7-15
• /
• 1997

High shear viscosity at several solids levels was measured for a number of pigment slurries and coating colors containing either anionic or amphoteric latex and analyzed according to Mooney and Eiler equations. Maximum packing fraction and intrinsic viscosity were obtained and compared. Eiler equation provides more credible information than Mooney equation on particle packing and intrinsic viscosity. The packing fraction obtained from Eiler equation was slightly greater than that obtained from static FCC measurement indicating the influence of pigment movement under the dynamic condition. Amphoteric latex caused 4-5% increase of maximum packing fraction of a coating color when its pH is lowered from 7 to 6, while anionic latex did not show any significant change in packing characteristics.

• Korea-Australia Rheology Journal
• /
• v.13 no.1
• /
• pp.47-54
• /
• 2001

Prediction of the maximum packing volume fraction with non-spherical particles has been one of the important problems in powder technology. The sphericity of fly ash particles depending on the particle diameter was measured by means of a CCD image processing instrument. An algorithm to predict the maximum packing volume fraction with non-spherical particles is proposed. The maximum packing volume fraction is used to predict the slurry viscosity under well dispersed conditions. For this purpose, Simha's cell model is applied for concentrated slurry with wide particle size distribution. Also, Usui's model developed for aggregative slurries is applied to predict the non-Newtonian viscosity of dense fly ash - water slurry. It is certified that the maximum packing volume fraction for non-spherical particles can be successfully used to predict slurry viscosity. The pressure drop in a pipe flow is predicted by using the non-Newtonian viscosity of dense fly ash-water slurry obtained by the present model. The predicted relationship between pressure drop and flow rate results in a good agreement with the experimented data obtained for a test rig with 50 mm inner diameter tube. Base on the design procedure proposed in this study, a feasibility study of fly ash hydraulic transportation system from a coal-fired power station to a controlled deposit site is carried out to give a future prospect of inexpensive fly ash transportation technology.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.51-63
• /
• 1999

The effects of high filler loading technique on the reliability of epoxy molding compound (EMC) as a microelectronic encapsulant was investigated. The method of high filler loading was established by the improvement of maximum packing fraction using the simplified packing model proposed by Ouchiyama, et al. With the maximum packing fraction of filler, the viscosity of EMC wart lowered and the flowability was improved. As the amount of filler in EMC increased, several properties such as internal stress and moisture absorption were improved. However, the adhesive strength with the alloy 42 leadframe decreased when the filler content was beyond the critical value. It was found that the appropriate content of filler was important to improve the reilability of EMC, and the optimum filler combination should be selected to obtain high reliable EMC filled with high volume fraction of filler.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.131-134
• /
• 2000

Increased temperature adversely affects the reliability of a device. So, package material should have high thermal diffusion, i.e., high thermal conductivity. And, there are several other physical properties of polymeric materials that are important to microelectronics packaging, some of which are a low dielectric constant, a low coefficient of thermal expansion (CTE), and a high flexural strength. In this study, to get practical maximum packing fraction of AIN (granular type) filled EMC, the properties such as the spiral flow, thermal conductivity, CTE, and water resistance of AIN-filled EMC (65-vol%) were evaluated according to the size of AIN and the filler-size distribution. Also, physical properties of AIN filled EMC above 65-vol% were evaluated according to increasing AIN content at the point of maximum packing fraction (highly loading condition). The high loading conditions of EMC were set $D_L/D_S$=12 and $X_S$=0.25 like as filler of sphere shape and the AIN filled EMC in this conditions can be obtained satisfactory fluidity up to 70-vol%. As a result, the AIN filled EMC (70-vol%) at high loading condition showed improved thermal conductivity (about 6 W/m-K), dielectric constant (2.0~3.0), CTE(less than 14 ppm/$^{\circ}C$) and water resistance. So, the AIN filled EMC (70-vol%) at high loading condition meets the requirement fur advanced microelectronic packaging materials.

• Journal of the Korean Magnetics Society
• /
• v.11 no.4
• /
• pp.157-162
• /
• 2001

Rheological characteristics of Sm-Co type plastic magnet compound for powder injection molding process were investigated with the variation of the magnetic powder size, their relative contents and volume fraction using the mixture of fine and coarse powder. Shear viscosity of Sm-Co type compound was decreased with increasing the size of coarse powder due to the increase of powder packing density. However, the smaller the average size of fine powder resulted in the higher viscosity of compound due to the increase of agglomeration force. In case of mechanically milled Sm-Co type powder, the viscosity of compound with the mixture of coarse powder of 125∼75 ㎛ and fine powder of average size of 4.9 ㎛ greatly depends on their relative contents and shows a minimum value at the 60 % coarse powder fraction. This means that the compound shows a maximum packing density at the 60% coarse powder fraction. Compound viscosities satisfied well the rheological model with the volume fraction of magnetic powder, and maximum volume fraction of magnetic powder in Sm-Co type compound for powder injection molding was about 66%.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.4
• /
• pp.96-106
• /
• 2017

In pressable polymer bonded explosives (PBXs), densification occurs due to rearrangement and deformation of explosive particles during pressing. If brittle explosives are compressed till particle fraction become higher than theoretical random close packing fraction (RCPF), bigger particles should be fractured to fill the void. In this study, multi-modal particle system was introduced for the decrease in possibility of particle fracture during compression expecting decrease in shock sensitivity of highly filled pressable PBX. The experimental results showed the trimodal particle system had low sensitivity with high density, compared to bimodal particle system.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.4
• /
• pp.109-115
• /
• 2015

High performance fiber reinforced cementitious composite (HPFRCC) can provide high fracture energy absorption as well as high strength with high fiber volume fraction. The increased fracture energy helps resisting high frequency loadings, such as earthquake, impact or blast. This study investigates the flexural performance of slurry infiltrated fiber concrete (SIFCON), one of the important HPFRCC, with respect to varying fiber volume fraction. The maximum fiber volume fraction was 8.0 % and reduced to 6.0% by 0.5% and the maximum volume fraction is obtained by packing fibers with simple tapping by hands. The used fiber was a steel fiber with the length 30 mm and the diameter of 0.5 mm. The flexural strengths were 48.7 MPa at 8.0 % and 22.8 MPa at 6.0 %. The measured flexural strength is much higher compared to other cememtitious composite materials but decreased proportional to the fractions. This result implies that for SIFCON considered herein the reduced amount of steel fibers may affect its flexural performance in a negatively way. The flexural toughness, an index to represent the fracture energy absorption, also decreased with the reduced fiber amount.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.59 no.4
• /
• pp.435-444
• /
• 2014

This study was carried out to isolate and characterize the flavonoids present in corn silks. Maysin content in the unpollinated corn silks (Kwangpyeongok) showed its highest level at 3 days after silking, and decreased thereafter, while the content of open pollinated silks were consistently decreased after silking. This result indicates that the maysin content is considerably affected by the pollination of corn silk. Unpollinated corn silks were collected with excising, and ethanol employed to extract flavonoids at common temperature for 9 days. After extraction, chlorophyll, lipids etc. were removed with methylene chloride, then submitted to flash column cartridge ($150{\times}40mm$ i.d.) packed with a preparative $RP-C_{18}$ bulk packing material ($125{\AA}$, $55-105{\mu}m$), and monitored at 352 nm. Four fractions, fraction-I, -II, -III, and -IV, were isolated from ethanolic extract of corn silks. Absorption spectrum of fraction I showed its maximum intensity (${\lambda}_{max}$) at 327 nm and 239 nm, fraction-II showed its maximum intensity at 339 nm and 274 nm, fraction-III showed its maximum intensity at 345 nm and 277 nm, and fraction-IV showed its maximum intensity at 352 nm, 270 nm, 257 nm, respectively. On the baisis of ESI micro-TOF analysis, fraction-I was identified as chlorogenic acid (m/z 355, 3-(3,4-dihydroxycinnamoyl) quinic acid, $C_{16}H_{18}O_9$), fraction-II identified as a mixture of chlorogenic acid and luteolin 3'-methyl ether 7-glucuronosyl-($1{\rightarrow}2$)-glucuronide (m/z 653, $C_{28}H_{28}O_{18}$), fraction-III identified as a mixture of chlorogenic acid luteolin 7-O-neohesperidoside (m/z 595, $C_{27}H_{30}O_{15}$), and luteolin 3'-methyl ether 7-glucuronosyl-($1{\rightarrow}2$)-glucuronide, and fraction-IV identified as maysin (m/z 577, 2"-O-${\alpha}$-L-rhamnosyl-6-C-(6-deoxy-xylohexose-4-ulosyl)luteolin, $C_{27}H_{28}O_{14}$), respectively. From the ethanolic extract of corn silks, fraction-I was obtained about 35 mg/100 g F.W., fraction-II was about 48 mg/100 g F.W., fraction-III was about 46 mg/100 g F.W., and fraction-IV was about 138 mg/100 g F.W., respectively.

• Applied Biological Chemistry
• /
• v.39 no.5
• /
• pp.368-373
• /
• 1996

Korean general medicinal herbs-sasam, gilkyung, jakyak, danggwi, hwangki, and chunkung-were added In the normal brewing procedure as a raw material or in the distilling procedure as a packing material. The distillates from the former procedure and those from the latter procedure were compared in quality and distillation properties. As distillation proceeded, pH of the medicinal herb wine distillate and the control(not added herbs) distillates were decreased, whereas that of the herb packing distillate was increased slowely of $0.05{\sim}0.97$ during $1{\sim}4$ fractions and decreased remarkably of $0.92{\sim}0.98$ afterward. Average pH was the highest of 5.70 in jakyak and lowest of 4.37 In gilkyung. Absorbances of the herb Packing distillate were decreased rapidly of $0.60{\sim}1.59$ in the $1{\sim}4$ fractions but slowely of $0.19{\sim}0.54$ in the next fractions. During distillation both fractional alcohol concentration of the distillates and distillation rate were decreased. Their values were decreased more slowly than the control. Distillation rates of medicinal herb wine distillate were varied by medicinal herb varieties and alcohol concentration of fermented wine. Danggwi and control showed the highest average distillation rate as $0.12\;m{\ell}/sec$ and gilkyung the lowest value as $0.073\;m{\ell}/sec$. Maximum concentration of index component, paeoniflorin of jakyak was observed as 293 mg% in the 5th fraction of herb packing distillate and decrusin of danggwi as 3514 mg% In the 1st fraction of herb packing distillate. The extraction rate was 41.3% for paeoniflorin and 20.5% for decrusin. From sensory evaluation, the highest overall Qualify was observed in the medicinal herb wine distillate of hwangki added wine, the next in those of danggwi and jakyak added wine.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.225-231
• /
• 2014

The rheological properties of highly concentrated polymer bonded explosive simulant were studied by using poly(ethylene-co-vinyl acetate) with 30 and 60% vinyl acetate (VA) content as a binder, respectively. Calcium carbonate and Dechlorane, whose physical properties are similar to resarch department explosive (RDX)'s, were used as fillers. The suspensions were mixed in a batch melt mixer and it was possible to fill 75 v% at maximum. From dynamic mechanical analysis, Dechlorane showed higher interaction with binder resins than that with calcium carbonate fillers. The effects of microstructural change on the rheological properties of the suspensions were investigated by a plate-plate rheometer with constant shear rate and constant shear stress modes, respectively. The theoretical maximum packing fraction of EVA31/Dechlorane suspension obtained from Krieger-Dougherty equation was 70 v% and it was thought that 2000 Pa was proper shear stress condition for this melt processing.