• Journal of IKEEE
• /
• v.3 no.1 s.4
• /
• pp.118-125
• /
• 1999

A capacitance method to extract the metallurgical channel length of LDD MOSFET's, which is defined by the length between the metallurgical junction of substrate and source/drain under the gate, is presented. The gate capacitances of the finger type and plate type LDD MOSFET gate test patterns with same total gate area are measured. The gate bias of each pattern is changed, and the capacitances are measured with source, drain, and substrate bias grounded. The differences between two test pattern's capacitance data are plotted. The metallurgical channel length is extracted from the peak data at a maximum point using a simple formula. The numerical simulation using two-dimensional device simulator is performed to verify the proposed method.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1155-1158
• /
• 2004

Various inorganic alignment layers of nematic liquid crystal (NLC) molecules were investigated. Ar ion beam (IB) irradiation was utilized for alignment method and homogenous and homeotropic orientations with tilt angle were obtained on the suitable inorganic thin films. Proper doping materials were added to diamond-like carbon (DLC) films. In the case of homogeneous alignment, nitrogen doping affected the increase of pretilt angle, while the fluorine bonding in the DLC films was induced the tilted homeotropic alignment cause its extreme hydrophobic property. These results showed that ion beam irradiation method could be applied to the various alignment mode of NLC such as IPS, TN and MVA.

• Journal of Korea Foundry Society
• /
• v.13 no.5
• /
• pp.424-431
• /
• 1993

A Numerical technique has been developed for the coupled heat transfer and fluid flow calculation during the casting process. In this method the SMAC technique was coupled with the concept of Volume of Fluid(VOF) to calculate melt free surface and velocity profiles within the melt, and the Energy Marker method coupled with the finite difference method was proposed for the convective and conductive heat transfer analysis in the casting. When comparing numerical calculations with experimental observations, a close correlation was evident. It has been shown that this technique is useful for proper gating and casting design, especially for thin-walled castings.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.980-981
• /
• 2006

In this study, bottom-up type powder processing and top-down type SPD (severe plastic deformation) approaches were combined in order to achieve full density of Carbon nanotube (CNT)/metal matrix composites with superior mechanical properties by improved particle bonding and least grain growth, which were considered as a bottle neck of the bottom-up method using the conventional powder metallurgy of compaction and sintering. ECAP (equal channel angular pressing), the most promising method in SPD, was used for the CNT/Cu powder consolidation. The powder ECAP processing with 1, 2, 4 and 8 route C passes was conducted at room temperature.

• Journal of Korea Foundry Society
• /
• v.11 no.4
• /
• pp.303-313
• /
• 1991

The Purification mechanism of high purity aluminum was studied through the variation of stirring speed and coolant flow rate in the stirring method. In the stirring method the degree of purification was changed as the following factors;the variation of diffusion boundary layer thickness the variation of growth rate and the solute concentration of the residual melt. The concentration of Fe and Si was decreased as the stirring speed and the radial distance increased. In a high stirring speed of 2000rpm with unidirectional stirring mode, the uniformity of solutes was obtained. On the other hand, the purification of Si was done by the combinations of stirring method, fractional melting and acid leaching. In the case of Si purification, the centrifugal force developed in the melt acted as the significant purification factor. It was possible to obtain the purified 3N grade Si crystal after the complete elimination of residual aluminum by fractional melting and acid leaching.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.298-303
• /
• 2000

We evaluated the electric properties of Bi-2223 jointed tapes processed by both resistive- and supercondcuting-joint methods. For the resistive-joint, filler materials of wood metal, Pb/Sn, In, and silver paste were used, whereas, for the superconductive-joint, the lap joint method were used. In the resistive-joint tape, it was observed that the electrical properties such as current transport property, n-value, and contact resistance of the tape were significantly related to the resistivity of filler materials. On the other hand, in the superconducting-joint tape, the current transport property was dependent on the uniaxial pressure. Specifically, the current transport property varied 50 to 80% with uniaxial pressure, probably due to the irregular microstructure in the transition region.

• 한국초전도학회:학술대회논문집
• /
• v.13
• /
• pp.64-64
• /
• 2003

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.328-329
• /
• 2005

Inorganic alignment layer (IAL) was deposited on an indium-tin-oxide (ITO) by using reactive sputtering deposition method. After deposited, IAL was irradiated by $Ar^+$ ion beam (IB) for liquid crystal (LC) alignment. IAL treated by various conditions such as IB energy, IB incident angle, and IB irradiation time had excellent alignment property and electro-optical property the same as that of PI. We investigated into the stability of ion beam treated IAL after a lapse of long time. However IAL irradiated IB did not occur degradation of electro-optical property. The results implied that IAL irradiated IB was adopted as LC alignment layer instead of rubbed polyimide.

• Journal of the Korean Society for Heat Treatment
• /
• v.5 no.3
• /
• pp.157-164
• /
• 1992

Barkhausen noise (BN) is created by the abrupt changes in the magnetization of materials under applied AC magnetizing field. These changes are known to be sensitive to residual and applied stresses. In this study, BN theory was reviewed and it was examined how BN intensity was affected by simultaneous stress, hardness and microstructural changes. Also, magnetoelastic effect was used to evaluate residual stresses through carrying out the cantilever beam test. An increase in BN intensity was observed when applied and residual stress changes from compression into tension. Microstructural softening by tempering also increased the amount of BN. Therefore, the quantitative evaluation of residual stress and microstructural changes will be possible, provided BN method is more studied about various materials through comparing with different stress measuring techniques.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.3
• /
• pp.249-252
• /
• 1999

Boriding is one of the chemical method to increase surface hardness as well as carburizing, and nitriding. Gas boriding and boron paste boriding methods were investigated to replace salt bath boriding. Boron paste boriding method is selected due to safety, small waste and low cost. And then boriding is also carried out micro-pulsed PECVD in order to increase efficiency of boriding. Mechanical properties, microstructure, surface concentration, and depth profile of borided layer is investigated by micro-vickers hardness tester, SEM, XRD, and AES.