• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.524-529
• /
• 2008

In this paper, in order to develop low loss multilayer actuator, piezoelectric properties of PZW-PMN-PZT multilayer actuator sintered at $900^{\circ}C$ low temperature were investigated according to the number of multilayer. The multilayer actuator was fabricated using tape casting method and used pure Ag internal electrode. The density above $8.0\;g/cm^3$ was obtained at all specimens. With increasing number of multilayer, effective electromechanical coupling factor($k_{eff}$) was increased. $k_{eff}$ of multilayer actuator shows the maximum value of 0.283 at 11 layers actuator. However, effective mechanical quality factor(Qm') was decreased according to the increase of number of multilayer. The Qm' of multilayer actuator showed the maximum value of 920 at 5 layers actuator.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.270-271
• /
• 2007

In this study, piezoelectric properties of PZW-PMN-PZT multilayer actuator sintered at $900^{\circ}C$ low temperature have been investigated. The multilayer actuator was fabricated by tape casting methods. The density above $8[g/cm^3]$ was obtained at all the specimens. Also, according to increasing the number of multilayer, effective electromechanical coupling factor$(k_{eff})$ showed increasing trend. The $k_{eff}$ of multilayer actuator showed the maximum value of 0.283 at 11 layer. However, according to increasing the number of multilayer, mechanical quality factor(Qm') showed decreasing tend. The Qm' of multilayer actuator showed the maximum value of 920 at 5 layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.257.1-257.1
• /
• 2014

We investigated characteristics of ITO/Ag-Pd-Cu (APC)/ITO multilayer electrodes prepared by direct current magnetron sputtering for use as an anode in organic solar cells (OSCs). To optimize electrical properties of ITO/APC/ITO multilayer, we fabricated the ITO/APC/ITO multilayer at a fixed ITO thickness of 30 nm as a function of APC thickness. Compare to the surface of Ag layer on ITO, the APC had a smooth surface morphology. At optimized APC thickness of 12 nm, the ITO/APC/ITO multilayer exhibited a sheet resistance of $6{\Omega}/square$ and optical transmittance of 84.15% at a wavelength of 550 nm which is comparable to conventional ITO/Ag/ITO multilayer. However, the APC-based ITO multilayer showed a higher average transmittance in a visible region than the Ag-based ITO multilayer. The higher average transmittance of ITO/APC/ITO multilayer indicated the multilayer is suitable anode for organic solar cells with P3HT:PCBM active layer. OSCs fabricated on the optimized ITO/ACP/ITO multilayer exhibited a better performance with a fill factor of 64.815%, a short circuit current of $8.107mA/cm^2$, an open circuit voltage of 0.59 V, and power conversion efficiency (3.101%) than OSC with ITO/Ag/ITO multilayer (2.8%).

• Journal of Magnetics
• /
• v.2 no.2
• /
• pp.58-66
• /
• 1997

Recently, artificially modulated magnetic multilayer materials, for examples giant magnetoresistant magnetic head materials and magneto-optic recording materials in the wavelength of a blue laser beam, attract great attention in the electronics industry due to their unique properties derived from the modulated multilayer structure. Since the multilayer structure as well as amorphous structure, is non-equilibrium state in terms of free energy, an assessment of the thermal staibility in the multilayer structure is crucially importnat both for basic research and applications. In this review paper, effective microscopic interdiffusion process in the two dimensional multilayer structure will be described in terms of steep concentration gradient effect, strain effect and magnetic transition effect.

• Journal of Magnetics
• /
• v.3 no.1
• /
• pp.21-30
• /
• 1998

An artificially modulated magnetic Co/Pd multilayer is one of the promising candidates for high density magneto-optic (MO) recording media, due to large Kerr rotation angle in the wavelength of a blue laser beam. however, since multilayer structure, as well as amorphous structure, is a non-equilibrium state in terms of free energy and MO recording is a kind of thermal recording which is conducted aound Curie temperature (Tc) of the recording media, when the multilayer is used for the MO recording media, changes in the multilayer structure are occurred as the amorphous structure do. Therefore, the assessment of the structural stability in the Co/Pd multilayer is crucially important both for basic research and applications. As the parameter of the structural stability in this research, modulation amplitude and particle size of the Co/Pd multilayer are measured in terms of Ar sputtering pressure and heat treatment temperature. From the results of the research, we find out that the magnetic exchange energy in the structural changes of a magnetic multilayer structure and suggest the operating temperature range for MO recording in the Co/Pd multilayer for the basic research and applications, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.7
• /
• pp.583-591
• /
• 2000

It this paper the multilayer chip band pass filter for next generation mobile communication phone is fabricated and designed. For the design the multilayer chip filter of non-contented equivalent circuit and contented equivalent circuit with attenuation pole is presented. Finally it is fabricated and designed using the multilayer chip filter of contented equivalent circuit with attenuation pole. The size insertion loss center frequency and band width of multilayer chip filter are 4.5$\times$3.2$\times$2.0[mm], 3.0[d.B] and 1945$\pm$25 MHz respectively. The multilayer chip filter was fabricated by screen printing with Ag electrode after tape casting. Simulation results of multilayer chip filter are compared with experimental results and found to be in excellent agreements.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.278.2-278.2
• /
• 2014

We have investigated the highly flexible and transparent Si-doped $In_2O_3$(ISO)/Ag/ISO multilayer grown on polyethylene terephthalate (PET) substrates using a roll-to-roll sputtering system. The electrical and optical properties of ISO/Ag/ISO multilayer electrodes depended on the insertion of a nano-size Ag layer. Due to the high conductivity of a nano-size Ag layer, the optimized ISO/Ag/ISO multilayer electrodes showed the lowest resistivity of $3.679{\times}10^{-5}Ohm-cm$, even though the ISO/Ag/ISO multilayer electrodes was sputtered at room temperature. Furthermore, the ISO/Ag/ISO multilayer electrodes exhibited a high transmittance of 86.33%, because of the anti-reflection effect, comparable to Sn-doped $In_2O_3$ (ITO) electrodes. In addition, the ISO/Ag/ISO multilayer electrodes had a very smooth surface morphology without surface defects and showed good flexibility. The flexible OSCs fabricated on ISO(30nm)/Ag(8nm)/ISO(30nm) multilayer electrode showed a power conversion efficiency of 3.272%. This result indicates that the ISO/Ag/ISO multilayer is a promising transparent conducting electrode for flexible OSCs.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.545-550
• /
• 2013

Piezoelectric PMN-29PT single crystal multilayer actuators [100 $mm^2$ in cross section and 22 mm in length] are designed and fabricated by stacking square plates [$10{\times}10{\times}0.5(t)\;mm^3$] of PMN-29PT single crystals having a $d_{33}$ of about 1,500 pC/N. The characteristics of PMN-29PT multilayer actuators are compared with those of P-025.40P multilayer PZT ceramic actuators [490 $mm^2$ in cross section and 60 mm in length] produced by PI in Germany. Even though the total volume of the PMN-29PT single crystal multilayer actuator is only about 7.5% of that of the P-025.40P ceramic multilayer actuator, PMN-29PT single crystal multilayer actuators are expected to show very similar properties to P-025.40P ceramic actuators in terms of static stroke and blocking force. Therefore, on the basis of their smaller mass and volume compared to the conventional PZT ceramic multilayer actuators, piezoelectric PMN-29PT single crystal multilayer actuators have significant potential regarding the development of various high performance actuators for aerospace subsystems.

• Journal of Broadcast Engineering
• /
• v.26 no.2
• /
• pp.208-220
• /
• 2021

This paper evaluates the performance of multilayer VVC and SHVC. Multilayer VVC supports a multi-layer coding and many coding technologies have been added and extended compared to SHVC. For this reason, it is necessary to evaluate the multi-layer coding performance of VVC and the coding performance for inter-layer reference prediction. Multilayer VVC provides significant BD-rate improvement of AI 24.4%, RA 29.4%, LDB 29.4%, LDP 32.6% on average when compared to SHVC, so that it is shown that VVC can provide scalability more efficiently. On the other hand, the complexity of the encoding time increases by an average of 14 times and decoding time by an average of 1.8 times, which requires efforts to reduce the complexity.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.294-298
• /
• 2003

In this paper, the modeling and design of high-Q multilayer passives have been investigated, and multilayer diplexer for GSM/DCS applications has been designed and fabricated using the passives. To minimize the system, the configuration of a multilayer inductor has involved a square spiral structure. Modeling of a multilayer inductor was performed by the subsystems of distributed components, and using the modeling the optimal structures of the high-Q multilayer inductor could be designed by analyzing parasitics and couplings which affect their frequency characteristics. Multilayer diplexer for GSM/DCS application has been designed and fabricated using LTCC technology. LPF for GSM band had the passband insertion loss of less than 0.55 dB, the return loss of more than 12 dB, and the isolation level of more than 26 dB by locating attenuation pole at 1800 MHz. HPF for DCS band had the passband insertion loss of less than 0.82 dB, the return loss of more than 11 dB, and the isolation level of more than 38 dB by locating attenuation pole at 930 MHz.