• Journal of the Korean institute of surface engineering
• /
• v.29 no.4
• /
• pp.261-267
• /
• 1996

The characteristics and adhesion strength of TiN layer deposited by D. C. magnetron sputtering were investigated. Three types of TiN layers were deposited on STS304 stainless steel. Scratch tests were performed to determine the effect of deposition temperature, the thickness of coated TiN layer and the titanium inter-layer on the adhesion strength. TiN multilayer with titanium inter-layer showed the highest critical load in the deposition temperature range of $25^{\circ}C$ to $300^{\circ}C$. Adhesion strength of TiN multilayer with titanium inter-layer was raised from 15N to 20N by raising deposition temperature from $25^{\circ}C$ to $400^{\circ}C$. Adhesion strength was raised from 18N to 38N by increasing the thickness of outer layer of TiN multilayer from 2.1 $\mu\textrm{m}$ to 9.5 $\mu\textrm{m}$.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.4
• /
• pp.422-429
• /
• 1988

The photoconductive multilayer of Se-As(hole blocking layer)/Se-As-Te (photoconductive layer) /Se-As (layer for supporiting hole transport)/Se-As(layer or controlling total capacitance)/Sb2S3(electron blocking layer) was fabricated and its electrical and optical properties were investigated. The photoconductive multilayer is made of evaporated a-Se as the base material, doped with As and Te to prevent the crystallization of a-Se and to enhance red sensitivity, respectively. The multilayer with good image reproducibility has the following deposition condition. The first layer has the thickness of 250\ulcornerat the deposition rate of 250\ulcornersec. The second layer has the thickness of 800\ulcornerat the deposition rate of 250\ulcornersec. The third layer has the thickness of 125\ulcornerat the deposition rate of 250\ulcornersec. The fourth layer has the thickness of 1700\ulcornerunder the Ar gas ambient of 50x10**-3torr. The image pick-up tube, employing this multilayer demonstrates the following characteristics. The photosensitivity is 0.8, the resolution limit is above 300TV line, and the decay lag is about 7%. And spectral response convers the whole visible range. Therfore the application to color TV camera is expected.

• Journal of the Korean institute of surface engineering
• /
• v.27 no.6
• /
• pp.335-339
• /
• 1994

The underpotential deposition of zinc was investigated on carbon steel and nickel. The relationship be-tween the deposition potentials and the corresponding amounts of charge for deposited layers shows a very similar trend to the multilayer adsorption mechanism. The experimental results fit a mathematical model de-rived on the basis of the BET equation for the underpotential deposition.

• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.2
• /
• pp.85-89
• /
• 2012

Transparent conductive ZnO/Ag/ZnO (ZAZ) multilayer films were deposited by Radio frequency (RF) magnetron sputtering and direct current (DC) magnetron sputtering. The effects of post deposition vacuum annealing temperature on the structural, electrical and optical properties of the ZAZ multilayer films were investigated. The thickness of ZAZ films is kept constant at ZnO 50 nm/Ag 5nm/ZnO 45 nm, while the vacuum annealing temperatures were varied from 200 and $400^{\circ}C$, respectively. As-deposited ZAZ films exhibit a sheet resistance of $6.1{\Omega}/{\Box}$ and optical transmittance of 72.7%. By increasing annealing temperature to $200^{\circ}C$, the resistivity decreased to as low as $5.3{\Omega}/{\Box}$ and optical transmittance also increased to as high as 82.1%. Post-deposition annealing of ZAZ multilayer films lead to considerably lower electrical resistivity and higher optical transparency, simultaneously by increased crystallization of the films.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.465-469
• /
• 1995

We have investigated the effects of deposition angle on structural and magnetic properties of e-beam evaporated ${(4-{\AA}\;Co/9.2-{\AA}\;Pt)}_{23}$ multilayer thin films prepared on tilted substrates. It was found that the [111] crystallographic orientations of the multilayer thin films were not aligned with colummar growth orientations and they were remained to be normal to the substrate planes even though the deposition angle was severely oblique up to $60^{\circ}$. The analysis of the torque curve reveal that the intrinsic anisotropy energy was monotonically decreased with the deposition angle but the easy axis orientation parallel to the substrate normal was not much influenced by deposition angle.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.127-130
• /
• 2005

The properties of phosphorus doped ZnO multilayer thin films deposited on (001) sapphire substrates by pulsed laser deposition (PLD) were investigated by using annealing treatment at various annealing temperature after deposition. The phosphorus doped ZnO multilayer was composed of phosphorus doped ZnO layer and two pure ZnO layers on sapphire substrate. The structural. electrical and optical properties of the ZnOthin films were measured by X-ray diffraction (XRD). Hall measurements and photoluminescence (PL). As the annealing temperature optimized. the electrical properties of the ZnO multilayer showed a electron concentration of $1.56{\times}10^{16}/cm^3$, a resistivity of 17.97 ${\Omega}cm$. It was observed the electrical property of the film was changed by dopant activation effect as thermal annealing process

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.313-314
• /
• 2007

Ga-doped ZnO(GZO) multilayer coatings were prepared on glass by DC sputtering. Optimization of the deposition conditions of both AZO and Au layers were performed for better electrical and optical characteristics. The properties of multilayer were affected by the deposition process of both GZO and Au layers. The best multilayer coating exhibits low resistivity of $2.72{\times}10^{-3}\;{\Omega}-cm$ and transmittance of 77%. From these results, we can confirm a possibility of the application as transparent conductive electrodes.

• Journal of the Korean Vacuum Society
• /
• v.19 no.1
• /
• pp.52-57
• /
• 2010

$BiFeO_3/Pb(Zr_{0.52}Ti_{0.48})O_3$(BFO/PZT) multilayer thin films have been prepared on a Pt/Ti/$SiO_2$/Si(100) substrate by chemical solution deposition. BFO single layer, BFO/PZT bilayer and multilayer thin films were studied for comparison. X-ray diffraction analysis showed that the crystal structure of all films was multi-orientated perovskite phase without amorphous and impurity phase. The leakage current density at 500 kV/cm was reduced by approximately four and five orders of magnitude by bilayer and multilayer structure films, compared with BFO single layer film. The low leakage current density leads to saturated P-E hysteresis loops of bilayer and multilayer films. In BFO/PZT multlayer film, saturated remanent polarization of $44.3{\mu}C/cm^2$ was obtained at room temperature at 1 kHz with the coercive field($2E_c$) of 681.4 kV/cm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.511-514
• /
• 2000

Photoreactive multilayer films were prepared using long-chin alkyl diesters of p-phenylenediacrylic acid(p-PDA). In spite of the absence of hydrophilic groups in these molecules, they formed stable monolayers on the water surface when mixed with arachidic acid. Surface showed the presence of a condecsed phase and these monolayer could be transferred onto a substrate with Y-type deposition. The UV spectra of mixed multilayer films showed of absorption peak compared with that in solution. The linear relationship between absorbanoe and the number of layers supports the successful formation of multilayer films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.367-367
• /
• 2013

Commercial applications of indium tin oxide (ITO) can be separated into two useful areas. As it is perceived to bear electrical properties and optical transparency at once, its chance to apply to promising fields, usually for an optical device, gets greater in the passing time. ITO is one of the transparent conducting oxides (TCO), and required to carry the relative resistance less than $10^{-3}{\Omega}$/cm and transmittances over 80 % in the visible wavelength of light. Because ITO has considerable refractive index, there exist applications for anti-reflection coatings. Anti-reflection properties require gradual change in refractive index from films to air. Such changes are obtained from film density or nano-clustered fractional void. Glancing angle deposition (GLAD) method is a well known process for adjusting nanostructure of the films. From its shadowing effects, GLAD helps to deposit well-controlled porous films effectively. In this study, we are comparing the reference sample to samples coated with controlled ITO multilayer accumulated by an e-beam evaporation system. At first, the single ITO layer samples are prepared to decide refractive index with ellipsometry. Afterwards, ITO multilayer samples are fabricated and fitted by multilayer ellipsometric model based on single layer data. The structural properties were measured by using atomic force microscopy (AFM), and by scanning X-ray diffraction (XRD) measurements. The ellipsometry was used to determine refractive indices and extinction coefficient. The optical transmittance of the film was investigated by using an ultraviolet-visible (UV-Vis) spectrophotometer.