• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.21-29
• /
• 2004

Hot carrier degradation characteristics of Nano-scale CMOSFETs with dual gate oxide have been analyzed in depth. It is shown that, PMOSFET lifetime dominate the device lifetime than NMOSFET In Nano-scale CMOSFETs, that is, PMOSFET lifetime under CHC (Channel Hot Carrier) stress is much lower than NMOSFET lifetime under DAHC (Dram Avalanche Hot Carrier) stress. (In case of thin MOSFET, CHC stress showed severe degradation than DAHC for PMOSFET and DAHC than CHC for NMOSFET as well known.) Therefore, the interface trap generation due to enhanced hot hole injection will become a dominant degradation factor in upcoming Nano-scale CMOSFET technology. In case of PMOSFETs, CHC shows enhanced degradation than DAHC regardless of thin and thick PMOSFETs. However, what is important is that hot hole injection rather than hot electron injection play a important role in PMOSFET degradation i.e. threshold voltage increases and saturation drain current decreases due to the hot carrier stresses for both thin and thick PMOSFET. In case of thick MOSFET, the degradation by hot carrier is confirmed using charge pumping current method. Therefore, suppression of PMOSFET hot carrier degradation or hot hole injection is highly necessary to enhance overall device lifetime or circuit lifetime in Nano-scale CMOSFET technology

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.27-28
• /
• 2007

In this paper, Ni-Co alloy was used for improvement of thermal stability of Ni silicide. The proposed Ni/Ni-Co structure exhibited wide temperature window of rapid thermal process. Sheet resistance as well as cross-sectional profile showed stable characteristics in spite of high temperature annealing up to $700^{\circ}C$ for 30min. Therefore, the proposed Ni/Ni-Co structure is highly promising for highly thermal immune Ni silicide for nano-scale CMOSFET technology.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2007

In this paper, two kinds of initial oxidation methods i.e., SLTO(Slow Low Temperature Oxidation: $700^{\circ}C$) and RTO(Rapid Thermal Oxidation: $850^{\circ}C$) are applied prior to the plasma nitridation for ultra thin oxide of RPNO (Remote Plasma Nitrided Oxide). It is observed that SLTO has superior characteristics to RTO such as lower SS(Sub-threshold Slope) and improved Ion-Ioff characteristics. Low frequency noise characteristics of SLTO also showed better than RTO both in linear and saturation regime. It is shown that flicker noise is dominated by carrier number fluctuation in the channel region. Therefore, SLTO is promising for nano-scale CMOS technology with ultra thin gate oxide.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.18-22
• /
• 2008

In this paper, the Ni-Co alloy was used for thermal stability estimation comparison with Ni structure. The proposed Ni/Ni-Co structure exhibited wider range of rapid thermal process windows, lower sheet resistance in spite of high temperature annealing up to $700^{\circ}C$ for 30 min, more uniform interface via FE-SEM analysis, NiSi phase peak. Therefore, The proposed Ni/Ni-Co structure is highly promising for highly thermal immune Ni-silicide for nano-scale MOSFET technology.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.11
• /
• pp.1000-1004
• /
• 2006

In this paper, thermal stability of Ni-silicide formed on the SOI substrate with $B_{11}$ has been characterized. The sheet resistance of Ni-silicide on un-doped SOI and $B_{11}$ implanted bulk substrate was increased after the post-silicidation annealing at $700^{\circ}C$ for 30 min. However, in case of $B_{11}$ implanted SOI substrate, the sheet resistance showed stable characteristics after the post-silicidation annealing up to $700^{\circ}C$ for 30 min. The main reason of the excellent property of $B_{11}$ sample is believed to be the retardation of Ni diffusion by the boron and bottom oxide layer of SOI. Therefore, retardation of Ni diffusion is highly desirable lot high performance Ni silicide technology.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.6
• /
• pp.487-490
• /
• 2007

In this paper, the formation and thermal stability characteristics of Ni silicide using Ni-V alloy on Boron cluster ($B_{18}H_{22}$) implanted bulk and SOI substrate were examined in comparison with pure Ni for nano-scale CMOSFET. The Ni silicide using Ni-V alloy on $B_{18}H_{22}$ implanted SOI substrate after high temperature post-silicidation annealing showed the lower sheet resistance, no agglomeration interface image and lower surface roughness than that using pure Ni. The thermal stability of Ni silicide was improved by using Ni-V alloy on $B_{18}H_{22}$ implanted SOI substrate.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.3 s.345
• /
• pp.1-8
• /
• 2006

In this paper, reliability (HCI, NBTI) and device performance of nano-scale CMOSFETs with different channel stress were investigated. It was shown that NMOS and PMOS performances were improved by tensile and compressive stress, respectively, as well known. It is shown that improved device performance is attributed to the increased mobility of electrons or holes in the channel region. However, reliability characteristics showed different dependence on the channel stress. Both of NMOS and PMOS showed improved hot carrier lifetime for compressive channel stress. NBTI of PMOS also showed improvement for compressive stress. It is shown that $N_{it}$ generation at the interface of $Si/SiO_2$ has a great effect on the reliability. It is also shown that generation of positive fixed charge has an effect in the NBTI. Therefore, reliability as well as device performance should be considered in developing strained-silicon MOSFET.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.24-25
• /
• 2006

In this study, Ni silicide on the SOI substrate doped B11 is proposed to improve thermal stability. The sheet resistance of Ni-silicide utilizing pure SOI substrate increased after the post-silicidation annealing at $600^{\circ}C$ for 30 min. However, using the proposed B11 implanted substrate, the sheet resistance showed stable characteristics after the post-silicidation annealing up to $700^{\circ}C$ for 30 min.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.7
• /
• pp.569-574
• /
• 2007

In this paper, the reliability (NBTI degradation: ${\Delta}V_{th}$) and device characteristic of nano-scale PMOSFET with plasma nitrided oxide (PNO) is characterized in depth by comparing those with thermally nitrided oxide (TNO). PNO case shows the reduction of gate leakage current and interface state density compared to TNO with no change of the $I_{D.sat}\;vs.\;I_{OFF}$ characteristics. Gate oxide capacitance (Cox) of PNO is larger than TNO and it increases as the N concentration increases in PNO. PNO also shows the improvement of NBTI characteristics because the nitrogen peak layer is located near the $Poly/SiO_2$ interface. However, if the nitrogen concentration in PNO oxide increases, threshold voltage degradation $({\Delta}V_{th})$ becomes more degraded by NBT stress due to the enhanced generation of the fixed oxide charges.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.327-330
• /
• 2004

It is shown that the hot carrier degradation due to enhanced hot holes trapping dominates PMOSFETs lifetime both in thin and thick devices. Moreover, it is found that in 0.13 ${\mu}m$ CMOSFET the PMOS lifetime under CHC (Channel Hot Carrier) stress is lower than the NMOSFET lifetime under DAHC (Drain Avalanche Hot Carrier) stress. Therefore. the interface trap generation due to enhanced hot hole injection will become a dominant degradation factor. In case of thick MOSFET, the degradation by hot carrier is confirmed using charge pumping current method and highly necessary to enhance overall device lifetime or circuit lifetime in upcoming nano-scale CMOS technology.