• Journal of the Korean Applied Science and Technology
• /
• v.20 no.3
• /
• pp.243-250
• /
• 2003

Poly(methyl methacrylate)/clay nanocomposite particles with particle size of 275${\sim}$292 nm range were successfully prepared using emulsion polymerization. The content of montmorillonite based on the methyl methacrylate monomer was chosen as 30 wt.%. 2,2-azobis(isobuthylamidine hydrochloride) and n-dodecyltrimethylammonium chloride were used as an initiator and a surfactant in cationic emulsion system. Potassium persulfate and sodium lauryl sulfate were used as an initiator and a surfactant in anionic emulsion system. The evidence of intercalated /exfoliated structure of montmorillonite in the nanocomposite prepared in our experiment was confirmed by wide angle x-ray diffraction patterns of $d_{001}$ plane. Thermal behavior of nanocomposite was traced using DSC and TGA. It was found that the nanocomposite particle prepared by cationic emulsion system showed intercalated structured. We also found that the nanocomposite particle obtained from anionic emulsion system resulted in the fully exfoliated structure.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.5
• /
• pp.253-258
• /
• 2002

Nanocomposite means that the size of the second particles dispersed in the matrix is nanometer order. It was reported that this nanocompostie shows particular properties, different from a general composite in which the second particles are usually micrometer-order. Especially, mechanical properties were known to be enhanced largely. However, there is little report about how electroceramic properties are changed by making nanocomposite. Thus, in this research, we made PNN-PZT/Ag nanocomposite by hot-pressing method, and microscopic and dielectric properties are studied.

• Journal of Powder Materials
• /
• v.8 no.3
• /
• pp.207-209
• /
• 2001

Nano particles have recently been a major research interest, motivated by their unusual physical and chemical properties. Such particles can be synthesized using physical and chemical methods. The physical methods need expensive installation like vacuum induction furnace, whereas in chemical methods the process in generally very simple and low cost. In this study, simple and new fabrication process by using ultrasound was investigated to prepare the nano-sized metal particles on various powders at room temperature.

• Journal of Powder Materials
• /
• v.8 no.3
• /
• pp.179-185
• /
• 2001

Through the observation of wear scar of two ceramic materials, microstructural wear mechanisms was investigated. As for the $Al_2O_3$-5 vol% SiC nanocomposite, the grain boundary fracture was suppressed by the presence of SiC nano-particles. The intragranular SiC particles have inhibited the extension of plastic deformation through the whole grain. Part of plastic deformation was accommodated around SiC particles, which made a cavity at the interface between SiC and matrix alumina. On the other hand, gas-pressure sintered silicon nitride showed extensive grain boundary fracture due to the thermal fatigue. The lamination of wear scar was initiated by the dissolution of grain boundary phase. These two extreme cases showed the importance of microstructures in wear behavior.

• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.613-618
• /
• 2003

The magnetic heating effect of $SiO_2$coated $ \Upsilon-Fe_2$$O_3$nanocomposite particle due to magnetic relaxational loss of superparamagnetic regime was investigated by measuring the generated heat from nanocomposite particles in alternative applied magnetic fields. The commercial $ \Upsilon-Fe_2$$O_3$nanoparticles were coated by SiO$_2$in water solution with TEOS and the synthesized nanocomposite powders and its magnetic properties were characterized and compared with the raw$ \Upsilon-Fe_2$$O_3$nanoparticles. The 10∼30 nm sized $ \Upsilon-Fe_2$$O_3$. nanoparticles were coated by 5 nm thickness of amorphous $SiO_2$film. The nanocomposite particle has very low Mr and Hc value showing superparamagnetic behavior The magnetic heating effect of nanocomposite particle on surface coating phase of $SiO_2$was discussed in terms of superparamagnetic behaviors of each particles, and their potential for hyperthermia application was evaluated.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.3
• /
• pp.158-164
• /
• 2002

Nanocomposites consisting of a nanocrystalline brass matrix (grain size ; 20-100nm) with sub-micron sized Al2O3 particles (60-200nm) were prepared by pulsed current electrodeposition. The microhardness of the nanocomposite with a grain size of 90-100nm was approximately 1.7 times higher than that of a comparable electrodeposit with no particles. However, significant variations in microhardness were not observed between the nanocomposites with grain sizes of 20 nm and the comparable electrodeposit.

• Advances in nano research
• /
• v.13 no.4
• /
• pp.313-323
• /
• 2022

The microstructure and mechanical properties of Cr-Ni steel and Cr-Ni steel-matrix nanocomposites reinforced with nano-ZrO₂ particles were investigated in this study. Cr-Ni steel and Cr-Ni/ZrO₂ nanocomposites were produced using a combination of high-energy ball milling, pressing, and sintering processes. The microstructures of the specimens were analyzed using EDX and XRD. Compression and hardness tests were performed to determine the mechanical properties of the specimens. Nano-ZrO₂ particles were effective in preventing chrome carbide precipitate at the grain boundaries. While t-ZrO₂ was detected in Cr-Ni/ZrO₂ nanocomposites, m-ZrO₂ could not be found. Few α'-martensite and deformation bands were formed in the microstructures of Cr-Ni/ZrO₂ nanocomposites. Although nano-ZrO₂ particles had a negligible impact on the strength improvement provided by deformation-induced plasticity mechanisms in Cr-Ni/ZrO₂ nanocomposites, the mechanical properties of Cr-Ni steel were significantly improved by using nano-ZrO₂ particles. The hardness and compressive strength of Cr-Ni/ZrO₂ nanocomposite were higher than those of Cr-Ni steel and enhanced as the weight fraction of nano-ZrO₂ particles increased. Cr-Ni/ZrO₂ nanocomposite with 5wt.% nano-ZrO₂ particles had almost twofold the hardness and compressive strength of Cr-Ni steel. The nano-ZrO₂ particles were considerably more effective on particle-strengthening mechanisms than deformation-induced strengthening mechanisms in Cr-Ni/ZrO₂ nanocomposites.

• Tribology and Lubricants
• /
• v.39 no.3
• /
• pp.111-117
• /
• 2023

This paper presents an experimental investigation of the tribological characteristics of PTFE composites filled with nano CuO particles under low sliding speed and load. All the specimens were prepared by sintering. Before sintering, the mixture of PTFE powder and CuO particles were mixed by a high-speed mixer using CuO volume fractions of 0.2 vol. % and 5 vol. %. Each mixture was sintered at 350 ℃ for 30 min on the steel disk. We conducted ball-on-disk sliding test an hour using a steel ball against PTFE composites, including pure PTFE. The load and sliding speed used was 2 N and 0.01 m/s, respectively. Adding nano CuO particles increases the friction coefficient because of the abrasiveness of hard nano CuO particles. The highest coefficient of frictions was obtained from 5 vol. % CuO. Conversely, the lowest wear of the composites was obtained from the 5 vol. % CuO nanocomposite. This study reveals that the addition of nano CuO particles can lower the wear of PTFE, despite an increase in the coefficient of friction. However, the coefficient friction is still moderate compared to other engineering polymers. In addition, the amount of CuO nano particles has to be optimized to reduce friction and wear at the same time.

• Journal of Powder Materials
• /
• v.7 no.3
• /
• pp.149-153
• /
• 2000

In this study, the fabrication of $Al_2O_3$/5vol.%Cu nanocomposite and its mechanical property were discussed. The nanocomposite powders were produced by high energy ball milling of $Al_2O_3$ and Cu elemental powders. The ball-milled powders were sintered with Pulse Electric Current Sintering (PECS) facility. The relative densities of specimens sintered at $1200^{\circ}C$ and $1250^{\circ}C$ after soaking process at $900^{\circ}C$ were 96% and over 97%, respectively. The sintered microstructures were composed of $Al_2O_3$ matrix and the nano-sized Cu particles distributed on grain boundaries of $Al_2O_3$ matrix. The nanocomposite exhibited the enhanced fracture toughness compared with general monolithic $Al_2O_3$. The toughness increase was explained by the crack deflection and bridging by dispersed Cu particles.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.91.2-91.2
• /
• 2012

The TiB2-reinforced iron matrix nanocomposite (Fe-TiB2) was in-situ fabricated from titanium hydride (TiH2) and iron boride (FeB) powders by a simple and cost-effective process that combines the mechanical activation (MA) and a subsequent heat treatment (HT). Effect of milling factors and synthesized temperatures on the formation of the nanocomposite were presented and discussed. A differential thermal analyser (DSC-TG) was employed for examination of thermal behavior of MAed powders. Phases of the nanocomposite were confirmed by X-ray diffraction analysis (XRD). The morphologies and microstructure of nanocomposite were investigated by field emission-scanning electron microscopy (FE-SEM) and energy-dispersive X-ray spectroscopy (EDS). Phase composition and distribution were analyzed by electron probe X-ray microanalysis (EPMA). Results showed that TiB2 particles formed in nanoscale were uniformly distributed in alloyed Fe matrix.