• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.12
• /
• pp.1277-1282
• /
• 2004

ITO films on PET substrate were prepared by DC magnetron sputtering method using powdery target with different deposition conditions. In addition, the electrical and optical properties were investigated. As the sputtering power and working pressure were higher, the resistvity of ITO films increased. The optical transmittance deteriorated with increasing sputtering power and thickness. As the working pressure increased, however, the optical transmittance improved at visible region of light. From these results, we could deposited ITO films with 8${\times}$10$^{-3}$ $\Omega$-cm of resistivity and 80 % of transmittance at optimal conditions.

• Current Photovoltaic Research
• /
• v.3 no.3
• /
• pp.91-96
• /
• 2015

Optical modeling and characterization of transparent dye-sensitized solar cells (DSC) are presented to design and estimate DSC devices numerically. In order to model the inhomogeneous active layer of DSC, the porous structure of titanium oxide ($TiO_2$) and dye mixture, we prepared films consisting of layer by layer of the DSC's basic materials sequentially, and characterized the optical parameters of the films with the effective refractive index, which was extracted from the transmittance and reflectance measurements in ultra violet to near infra-red range. By using the effective refractive index, we made the optical model for DSC, and demonstrated that the optical model based on effective refractive index can be used to design and evaluate the performance of transparent-type DSC modules.

• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.5
• /
• pp.225-229
• /
• 2014

The influence of electron irradiation energy(eV) on the structural, electrical and optical properties of ITO/ZnO bi-layered films prepared with RF magnetron sputtering has been investigated. The ITO/ZnO show the lowest resistivity of $2.8{\times}10^{-4}{\Omega}cm$. The optical transmittance in a visible wave length region also increased with the electron irradiation energy. The film irradiated at 900 eV shows 82---- of optical transmittance in this study. By comparison of figure of merit, it was observed the optical transmittance and electrical resistivity of the films were dependent on the electron irradiation energy and optoelectrical performance of ITO/ZnO film is improved with electron irradiation.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.210-215
• /
• 2002

Optical Band-pass Filter(BPF) for the selected wavelength of 4300 nm was designed and fabricated on Si wager by alternately depositing Ge and $SiO_2$ thin layers by an electron beam evaporation technique. The fabricated BPF showed the optical transmittance characteristics of 58.2% with FWHM(Full Width at Half Maximum) of 204 nm at 4300 nm, but showed the transmittance less than 5% due to the reflectance over all the wavelength ranges except 4300 nm band. The $CO_2$ sensitivity of BPF was investigated with the transmittance as a function of $CO_2$ gas concentration using a sensing cell attached to FT-IR instrument. The transmittance of BPF was almost linearly decreased with increasing of $CO_2$ concentration in the range of from 500 to 5000 ppm. The sensing structure using double BPFs showed higher slop of transmittance vs $CO_2$ concentration, and thus higher gas sensitivity than that using a single BPF, even though the former had relatively lower transmittance.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.6
• /
• pp.965-970
• /
• 1994

ZnO transparent conducting oxide thin films have been prepared by Pyrosol deposition method and the effects of the different experimental variables on the electrical resistivity and optical transmittance of the prepared films have been investigated in details. The best film with a resistivity of about 8 X 10S0-2TΩcm and transmittance about 80% has been obtained at the substrate temperature of 4$25^{\circ}C$ by using HS12T+CHS13TOH(1:3) solvent and NS12T carrier gas after annealing at 20$0^{\circ}C$ for 40 minutes in vacuum. Furthermore, We have also found the effect of substrate temperature on crystallographic orientation and surface morphology. Annealing of the as-deposited film in vacuum leads to a substantial reduction in resistivity without affecting the optical transmittance and crystallographic orientation.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.2
• /
• pp.57-63
• /
• 1999

The optical absorption and transmittance of cow' crystalline were measured by spectrophotometer in the 200~800nm wavelength regions. The optical absorptions of crystalline composed of a high absorption band in the UV-A, UV-B, and appeared the light transmittance edge in the 400nm wavelength region, and completely transmitted without the absorption in the high wavelength regions than 400nm. Also, the optical absorption and transmittance had no temperature dependence. The optical transmittance spectrum of crystalline concord with the thin film structure of $n_0/(0.5H)L(LH)^6(0.5H)/n_s$ and $n_0{\mid}(0.5LH0.5L)^kL/1.25{\mid}4.0$ of long-pass edge filter form. In the artificial crystalline and inter lens layout, long-pass edge filter layout can UV cut off.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1985.01a
• /
• pp.21-23
• /
• 1985

By adding La$_2$O$_3$ to optical multicomponent glass composition, after making mother glass and core fiber that enable to enlarge the infrared transmittance region, then surveyed the optical properties. Through thermal analysis of the glass abstained by melt-quenching after selecting stable basic composition on devitrification and replace SiO$_2$ by 4-12wt% La$_2$O$_3$. As La$_2$O$_3$ increases up to l2wt% transition temperature, refractive index, density, deformation temperature increased, whereas thermal expansion coefficient decreased. As a result of inspectig transmittance in UV/VIS/IR region, visable region indicated the decrease of transmittance by increasing the La$_2$O$_3$ and transmittance region was enlarged by increasing the La$_2$O$_3$ in IR region. Also, fabricate core fiber at 820$^{\circ}C$ and severy the optical loss we could fact that La$_2$O$_3$ composition added 12wt% showed the minimum optical loss.

• Current Photovoltaic Research
• /
• v.10 no.1
• /
• pp.28-32
• /
• 2022

We investigated the optical and electrical characteristics of ITO/Ag/ITO (IAI) 3-layer thin films prepared by using RF/DC sputtering. To measure the thickness of all thin film samples, we used scanning electron microscopy. As a function of Ag thickness we characterized the optical transmittance and sheet resistance of the IAI samples by using UV-Visible spectroscopy and Hall measurement system, respectively. While the thickness of both ITO thin films in the 3-layered IAI samples were fixed at 50 nm, we varied Ag layer thickness in the range of 0 nm to 11 nm. The optical transmittance and sheet resistance of the 3-layered IAI thin films were found to vary strongly with the thickness of Ag film in the ITO (50 nm)/Ag(t₀)/ITO (50 nm) thin film. For the best transparent conducting oxide (TCO) electrode, we obtained a 3-layered ITO (50 nm)/Ag (t₀ = 8.5 nm)/ITO (50 nm) that showed an avrage optical transmittance, AVT = 90.12% in the visible light region of 380 nm to 780 nm and the sheet resistance, R_□ = 7.24 Ω/□.

• Journal of the Korean Vacuum Society
• /
• v.10 no.2
• /
• pp.194-200
• /
• 2001

In this study, the optical properties of diamond-like carbon(DLC) films, which was synthesized by 13.56 MHz rf plasma enhanced chemical vapor deposition system(PECVD), were investigated. We observed the variation of the transmittance and optical band gap with respect to deposition condition. The change of the transmittance and optical band gap of the DLC films were investigated as a function of RF power, working pressure, and additional gas. The optical band gap decreased with the increase of RF power and working pressure. We could verify the bond structures change of DLC films by observing the content of hydrogen using FT-IR spectroscopy. And the addition of hydrogen and nitrogen decreased the optical band gap by the breakage of C-H bond of DLC films during the deposition.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.9
• /
• pp.607-614
• /
• 2015

To provide the clear images from the direct light on electrical board and display devices, anti glare treatment of display cover glass is needed. In this study, the effects of surface treatment temperature, concentration, and etching solution coating thickness of the gel phase on optical elements control such as gloss, haze of reflected light and transmittance, were investigated. Cover glasses were treated at different coating thickness and additive concentration. The optical properties were examined using spectrophotometer, gloss and haze meter. The surface morphology and roughness were measured by the optical microscope and Ra measuring instrument. The etching rate and surface morphologies were dramatically affected by the concentration of acid additive in the viscous gel because of re-crystallization of components in the etching solution, hydrogel formation and coagulant after coating on glass substrate. In our experimental range, cover glass which is surface-treated with various optical properties as well as the morphology uniformity was obtained; in particular, optical properties could be controlled by etching solution coating thickness of the gel phase and the concentration of additive. The gloss was depended on the surface roughness and it showed the linear relationship between optical transmittance and haze of reflected light, respectively.