• KSBB Journal
• /
• v.15 no.4
• /
• pp.352-358
• /
• 2000

Preparation for the simplified separation of chitosandoligosaccharides from enzymatic hydrolysate was investigated. Two different types of chitosan beads as substrate were prepared as organic-based bead by W/O emulsion method and water-based bead by alkaline treatement. The average size of organic-based bead was $200{\mu}m$, and that of water based beads were $4000{\mu}m$, $100{\mu}m$, $30{\mu}m$, in diameter respectively. Enzyme stability was maintained over 80% at PH 6 after 24 hours. The optimal condition for the production of chitosanoligosaccharides was at pH 6.0, $50^{\circ}C$ and 40U (200U/g-chitosan) According to final oligosaccharide concentration water-based bed showed the similar result with that of organic-based bead even through it had smaller surface area attacked by chitosanse than that of organic-based bead. It is probable that the structure of water-based chitosan bead was looser than that of organic-based bead so enzyme penetrated easily into the bead structure. For the oligosaccharide production versus surface area the different size of water-based beads was investigated, Maxiaml production yield was observed in the $30{\mu}m$ beads. Consequently the water-based chitosan bead was better than the organic-based bead in this reaction system.

• Ocean and Polar Research
• /
• v.25 no.3
• /
• pp.277-286
• /
• 2003

Nitrification performance of fixed film biofilters using coarse sand, loess bead, or styrofoam beads in biofilter columns 1 meter high and 30cm in diameter were studied at different hydraulic and organic matter loading rates. Synthetic wastewater was supplied to the culture tank in order to maintain desired TAN concentrations in inlet water to biofilters. All the biofilters were conditioned 5 months before start of sampling. TAN and $NO_2-N$ conversion rates increased with an increase in the hydraulic loading rate (HLR). However, the improvement in biofilter performance was not linearly correlated to HLR in styrofoam bead filters. This is mainly due to the characteristics of the styrofoam beads used. TAN conversion rates of sand filters increased with the increase of HLR up to $200m^3/m^2$. per day. No increase in the TAN conversion rate was observed at the highest HLR since flooding on the media surface took place. HLR had a significant impact on the TAN conversion rates in loess bead filter up to the highest HLR tested (P<0.05). TAN conversion rates were much less at organic matter loading rates of 9 and 18kg $O_2/m^3$ per day than those without the addition of organic matter in styrofoam bead filters. The addition of glucose resulted in a reduction of the TAN conversion rate from 540 to 284g $TAN/m^3$ per day. No significant difference of TAN conversion rates between the two organic matter loading rates was found (p<0.05). This indicates that the impact of organic matter on nitrification becomes less and less sensitive with an increase in the COD/TAN ratio. At an organic matter loading rate of 9kg $O_2/m^3$. per day, a great reduction of TAN conversion rates was observed in sand filters and loess bead filters. Clearly, organic matter can be one of the most Important Impacting factors on nitrification. $NO_2-N$ conversion rates showed a similar trend for TAN. Based on the TAN and nitrite conversion rates, styrofoam beads showed the best performance among the three filter media tested. Also, the low gravity and price of styrofoam beads make the handling easier and more cost-effective for commercial application. The results obtained at the highest organic matter loading rates can be used in the biofilter design in recirculating aquaculture system.

• Journal of Applied Biological Chemistry
• /
• v.59 no.1
• /
• pp.75-81
• /
• 2016

Glutaraldehyde was used as a cross-linking agent for immobilization of purified ${\alpha}$-amylase from Exiguobacterium sp. DAU5. Befitting concentration of glutaradehyde and cross-linking time is the key to preparation of cross-linking chitosan beads. Based on optimized immobilization condition for ${\alpha}$-amylase, an overall yield of 56% with specific activity of 2,240 U/g on chitosan beads and 58% with specific activity of 2,320 U/g on chitosan-carbon beads was obtained. The optimal temperature and pH of each immobilized enzyme activity were $50^{\circ}C$ and 50 mM glycine-NaOH buffer pH 8.5, respectively. Those retained more than 75 and 90% of its maximal enzyme activity at pH 7.0-9.5 and after incubation at $50^{\circ}C$ for 1 h, respectively. In addition, the immobilization product showed higher organic-solvent tolerance than free enzymes. The mode of hydrolyzing soluble starch revealed that the ${\alpha}$-amylase possessed high hydrolyzing activity. These results indicate that chitosan is good support and has broad application prospects of enzyme immobilization.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.6
• /
• pp.595-601
• /
• 2016

The insulation performance of the insulation currently used in building structures is reflected only during design based on initial performance and the reduction in heat insulation performance due to the degradation of long-term durability is not reflected. This study reviewed the degradation of heat insulation performance due to the durability degradation of insulating materials through the accelerated durability test. The study findings showed that the foamed polystyrene insulation bead method did not show performance degradation due to aging in the standard environmental condition and laboratory accelerated test condition but the performance is degraded in the freeze-thaw test condition. On the other hand, in the case of the extrusion method, the degradation of the heat insulation performance was less in the freeze-thaw test condition, but the rapid performance degradation was caused by the release of the internal gas at the beginning of aging. In addition, the hard polyurethane foam insulation showed better initial insulation performance than other insulation materials, but the performance was found to be degraded somewhat under laboratory accelerated test conditions and freeze-thaw test conditions.

• Journal of the Korean Ceramic Society
• /
• v.54 no.1
• /
• pp.49-54
• /
• 2017

In this study, based on hydrolysis and condensation via $St{\ddot{o}}ber$ process of sol-gel method, synthesis of mono-dispersed silica nanoparticles was carried out with hydrophilic solvent. This operation was expected to be a more simplified process than that with organic solvent. Based on the sol-gel method, which involves simply controlling the particle size, the particle size of the synthesized silica specimens were ranged from 30 to 300 nm by controlling the composition of tetraethylorthosilicate (TEOS), DI water and ammonia solution, and by varying the stirring speeds while maintaining a fixed amount of ethanol. Increasing the content of DI water and decreasing the content of ammonia caused the particle size to decrease, while controlling the stirring speed at a high level of RPMs enabled a decrease of the particle size. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) were utilized to investigate the success factors for synthesizing process; Field emission scanning electron microscopy (FE-SEM) was used to study the effects of the size and morphology of the synthesized particles. To analyze the dispersion properties, zeta potential and particle size distribution (PSD) analyses were utilized.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.16.1-16.1
• /
• 2011

$TiO_2$ is a promising material for gas sensors. To achieve high sensitivities, the material should exhibit a large surface-to-volume ratio and possess the high accessibility of the gas molecules to the surface. Accordingly, a wide variety of porous $TiO_2$ nanomaterials synthesized by wet-chemical methods have been reported for gas sensor applications. Nonetheless, achieving the large-area uniformity and comparability with well-established semiconductor production processes of the methods is still challenging. An alternative method is soft-templating which utilizes nanostructured inorganic or organic materials as sacrificial templates for the preparation of porous materials. Fabrication of macroporous $TiO_2$ films and hollow $TiO_2$ tubes by soft-templating and their gas sensing applications have been reported recently. In these porous materials composed of assemblies of individual micro/nanostructures, the form of links or necks between individual micro/nanostructures is a critical factor to determine gas sensing properties of the material. However, a systematic study to clarify the role of links between individual micro/nanostructures in gas sensing properties of a porous metal oxide matrix is thoroughly lacking. In this work, we have demonstrated a fabrication method to prepare highly-ordered, embossed $TiO_2$ films composed of anatase $TiO_2$ hollow hemispheres via soft-templating using polystyrene beads. The form of links between hollow hemispheres could be controlled by $O_2$ plasma etching on the bead templates. This approach reveals the strong correlation of gas sensitivity with the form of the links. Our experimental results highlight that not only the surface-to-volume ratio of an ensemble material composed of individual micro/nanostructures but also the links between individual micro/nanostructures play a critical role in evaluating the sensing properties of the material. In addition to this general finding, the facileness, large-scale productivity, and compatability with semiconductor production process of the proposed fabrication method promise applications of the embossed $TiO_2$ films to high-quality sensors.