• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.386-386
• /
• 2012

We studied a bilateral switching device for spin transfer torque (STT-MRAM) based on 3D device simulation. Metal/P/N+or Metal/N/P+ junction device with $30{\times}30nm2$ area which is composed of one side schottky junction at Metal/P/N+ and Metal/N/P+ provides sufficient bidirectional current flow to write data by a drain induced barrier lowering (DIBL). In this work, Junction device confirmed that write current is more than 30 uA at 2 V, It is also has high on-off ratio over 105 under read operation. Junction device has good process feasibility because metal material of junction device could have been replaced by bottom layer of MTJ. Therefore, additional process to fabricate two outer terminals is not need. so, it provides simple fabrication procedures. it is expected that Metal/P/N+ or Metal/N/P+ structure with one side schottky junction will be a promising switch device for beyond 30 nm STT-MRAM.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.30.2-30.2
• /
• 2010

Nano-scale p-n junction can generate various nano-scale functional devices such as nanowire light emitting diode, nanowire solar cell, and nanowire sensor. The core shell type nanowire p-n junction has been considered for the high efficient devices in many previous reports. On the other hand, although device efficiency is relatively lower, the cross bar type p-n junction has simple topological structure, suggested by C.M. Lieber group, to integrate easily many p-n junction devices in one board. In this study, for the integration of the cross bar nanowire p-n junction device, a simple fabrication route, employed dielectrophoretic array and direct printing techniques, was demonstrated by the successful fabrication and programmable integration of the nanowire cross bar p-n junction solar cell. This direct printing process will give the single nanowire solar cell the opportunity of the integration on the circuit board with other nanowire functional devices.

• 대한전자공학회논문지SD
• /
• 제39권10호
• /
• pp.25-34
• /
• 2002

본 논문에서는 코발트 실리사이드가 형성된 얕은 p+-n과 n+-p 접합의 전류-전압 특성을 분석하여 silicidation에 의해 형성된 Schottky contact 면적을 구하였다. 역방향 바이어스 영역에서는 Poole-Frenkel barrier lowering 효과가 지배적으로 나타나서 Schottky contact 효과를 파악하기가 어려웠다. 그러나 Schottky contact의 형성은 순방향 바이어스 영역에서 n+-p 접합의 전류-전압 (I-V) 동작에 영향을 미치는 것으로 확인되었다. 실리사이드가 형성된 n+-p 다이오드의 누설전류 증가는 실리사이드가 형성될 때 p-substrate또는 depletion area로 코발트가 침투퇴어 Schottky contact을 형성하거나 trap들을 발생시켰기 때문이다. 분석결과 perimeter intensive diode인 경우에는 silicide가 junction area까지 침투하였으며, area intensive junction인 경우에는 silicide가 비록 공핍층이나 p-substrate까지 침투하지는 않았더라도 공핍층 근처까지 침투하여 trap들을 발생시켜 누설전류를 증가시킴을 확인하였다. 반면 p+-n 다이오드의 경우 Schottky contact이발생하지 않았고 따라서 누설전류도 증가하지 않았다. n+-p 다이오드에서 실리사이드에 의해 형성된 Schottky contact 면적은 순방향 바이어스와 역방향 바이어스의 전류 전압특성을 동시에 제시하여 유도할 수 있었고 전체 접합면적의 0.01%보다 작게 분석되었다.

• Journal of information and communication convergence engineering
• /
• 제5권4호
• /
• pp.324-327
• /
• 2007

In this paper, the p-n junction depth with nondestructive method by using scanning electron microscopy (SEM) is determined and conformed. By measuring the critical short circuit current on the p-n junction which induced by electron beam and calculating generation range, the diffusion depth can be obtained. It can be seen that values destructively measured by constant angle lapping and nondestructively by this study almost concur. As this result, it is purposed that diffusion depth of p-n junction can be easily measured by nondestruction. This nondestructive method can be recommended highly to the industrial analysis.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.385-385
• /
• 2012

A two terminal N+/P/N+ junction device to replace the conventional selective transistor was studied as a bilateral switching device for spin transfer torque (STT) MRAM based on 3D device simulation. An N+/P/N+ junction structure with $30{\times}30nm$ area requires bi-directional current flow enough to write a data by a drain induced barrier lowering (DIBL) under a reverse bias at N+/P (or P/N+ junction), and high current on/off ratio of 106. The SiGe materials are widely used in hetero-junction bipolar transistors, bipolar compensation metal-oxide semiconductors (BiCMOS) since the band gap of SiGe materials can be controlled by changing the fraction and the strain epilayers, and the drift mobility is increased with the increasing Ge content. In this work, N+/P/N+ SiGe material based junction provides that drive current is increased from 40 to $130{\mu}A$ by increased Ge content from 10~80%. When Ge content is about 20%, the drive current density of SiGe device substantially increased to 2~3 times better than Si-based junction device in case of 28 nm P length, which is sufficient current to operation of STT-MRAM.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.55-56
• /
• 2007

The p-type ZnO thin film, fabricated by means of the ampoule-tube method, was used to make the ZnO p-n junction, and its characteristics was analyzed. The ampoule-tube method was used to make the p-type ZnO based on the As diffusion, and the hall measurement was used to confirm that the p-type is formed. the current-voltage characteristics of the ZnO p-n junction were measured to confirm the rectification characteristics of a typical p-n junction and the low leakage voltage characteristics. Using the ampoule-tube to fabricate the p-type ZnO will provide a very useful technology for producing the UV ZnO LED and ZnO-based devices.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.481-482
• /
• 2012

• 전자공학회논문지A
• /
• 제29A권8호
• /
• pp.71-77
• /
• 1992

According to increasing the doping concentration in p-n junction, a tunneling current through trap as well as SRH(Shockley-Read-Hall) generation-recombination current in depletion region occurs. It is the tunneling current that is a dominant current at the forward bias. In this paper, the new tunneling-recombination equation is derived. The thermal generation-recombination current and tunneling current though trap can be easily calculated at the same time because this equation has the same form as the SRH generation-recombination equation. For the validity of this equation, 2 kind of samples are simulated. The one is $n^{+}$-p junction device fabricated with MCT(Mercury Cadmium Telluride, mole fraction=0.29), the other Si n$^{+}-p^{+}$ junction. From the results for MCT $n^{+}$-p junction device and comparing the simulated and expermental I-V characteristics for Si n$^{+}-p^{+}$ junction, it is shown that this equation is a good description for tunneling through trap and thermal generation-recombination current calculation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.410-411
• /
• 2007

To investigate the ZnO LED which are interested in the next generation of short wavelength LEDs and Lasers, the ZnO thin films were deposited by RF magnetron sputtering system. The p-type ZnO thin film, fabricated by means of the ampoule-tube method, was used to make the ZnO p-n junction, and its characteristics was analyzed. The ampoule-tube method was used to make the p-type ZnO based on the As diffusion, and the hall measurement was used to confirm that the p-type is formed. the current-voltage characteristics of the ZnO p-n junction were measured to confirm the rectification characteristics of a typical p-n junction and the low leakage voltage characteristics. Analysis of ZnO LED V-I curve will provide a very useful technology for producing the UV ZnO LED and ZnO-based devices.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.126-129
• /
• 2001

A p-n junction was obtained by the deposition of an n-type ZnO thin film on a p-type Zn-doped InP substrate. The Zn-doped InP substrate has been made by the diffusion of Zn with sealed ampoule technique. The ZnO deposition process was performed by pulsed laser deposition (PLD). The p-n junction was formed and showed a typical I-V characteristic. We will also discuss about the realization of an ultraviolet light-emitting diode (LED). The structure of n-ZnO/p-Zn-doped InP could be a good candidate for the realization of an ultraviolet light-emitting diode or an ultraviolet laser diode.