• 한국자동차공학회논문집
• /
• 제19권1호
• /
• pp.32-37
• /
• 2011

In car refinishing, the paint film characteristics of clear coat play an important role in appearance quality. Thus, Primarily in this research, the variance of brightness with the change of the thickness of paint film is investigated. Besides, as changing the thickness of paint film, the correlation between surface leveling(which is one of appearance characteristics) is investigated in this research. Throughout this investigation, we come to know that the increase of clear coat paint film thickness leads the improvement of appearance characteristics within specific range of thickness. Furthermore, the fact that too thick paint film does not increase the brightness or appearance characteristic any more is known. The optimum thickness of clear coat film for the best and appearance characteristics is derived from this research and more efficient way of determining optimum thickness of paint film is found. Particularly, haze value and waviness have more influence on vividness than brightness. Throughout all experiments, the appearance characteristics are much better at painted horizontally than vertically. These results are derived due to the facts that to obtain the same paint film thickness at painted vertically with painted horizontally is difficult and the way of vertical painting is different from horizontal painting. Therefore, the improvement of vertical painting and horizontal painting are required.

• Corrosion Science and Technology
• /
• 제21권2호
• /
• pp.121-129
• /
• 2022

A study on water-based epoxy coated on mild steel using the electroplating method was conducted to optimize the process parameters for dry film thickness to achieve superior paint quality at optimal cost in an automotive plant. The regression model was used to adjust various parameters such as electrode voltage, bath temperature, processing time, non-volatile matter, and surface area to optimize the dry film thickness. The average dry film thickness computed using the model was in the range of 15 - 35 ㎛. The error in the computed dry film thickness with reference to the experimentally measured dry film thickness value was - 0.5809%, which was well within the acceptable limits of all paint shop standards. Our study showed that the dry film thickness on mild steel was more sensitive to electrode voltage and bath temperature than processing time. Further, the presence of non-volatile matter was found to have the maximum impact on dry film thickness.

• 대한조선학회논문집
• /
• 제49권5호
• /
• pp.433-439
• /
• 2012

Anticorrosive paint is the most widely used in shipbuilding and the dry film thickness is very important in terms of productivity and assurance of anticorrosive performance. However, it is difficult to achieve the recommended target film thickness because the dry film thickness depends on labor's skill in practice and is affected by a number of parameters, such as spray pressure, paint flow rate, tip size, spray distance, SVR(Solid Volume Ratio), etc. Present paper derives an empirical equation through the correlation analysis of parameters selected by spray experiments of anti corrosive painting in order to predict the coated status. Comparing the calculated results with practical data, we show that the empirical equation can successfully expect DFT(Dry Film Thickness).

• 한국세라믹학회지
• /
• 제35권11호
• /
• pp.1155-1161
• /
• 1998

브라운관 funnel glass 내며의 흑연 피막의 저항에 관하여 연구하기 위하여 흑연이 함유된 도전성 도료를 제조하여 flow coating 방법으로 28" wide TV용 funnel glass 내면에 도포하고 흑연피막의 특성과 브라운관의 동작 특성을 평가하였다. 고형분 농도가 증가함에 따라 도전성 도료의 점도와 흑연피막의 두께는 증가하였으며 흑연피막의 전기저항은 감소하였다. 도포 후 건조조건에 따라서도 도전막의 표면상태, 전기저항 및 브라운관의 초기동작 특성등이 다르게 나타났다. 도전성 도료의 고형분 농도는 27%, 점도는 13 cps 전후에서 안정한 흑연피막을 제조할 수 있었으며, 이 때 진공특성이 최적의 상태로 나타났다. 그리고 도전성 도료의 상태와 제조조건에 따라서 브라운관의 다른 전지적 특성들도 변할 수 있기 때문에 브라운관 전체의 특성을 동시에 평가를 해야한다고 생각한다. 그리고 funnel glass에서의 부의 별 저항산포 차리를 줄이기 위해서는 도포 시에 도전성 도료를 주입하는 위치, 건조 조건, funnel glass의 예열 온도 등에 대한 조사도 이루어져야 한다고 생각한다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.249-257
• /
• 2004

Drying and curing characteristics of PCM resins using the induction heater and short-wave infrared emitter module was studied to develop a compact oven system for the high speed CCL and post-treatment equipment. Drying of the polyester resins using the induction heater and infrared heater showed that the blistering tendency of polyester resin coating increased regardless of additives and colors of resins as the heating rate and/or dry film thickness increased. The blistering of polyester resin coating layer occurred when the heating speed was over than $25^{\circ}C/sec$ for the dry film thickness of $19\~20um$, which is the typical thickness of finish coating in CCL. So did it when the heating speed was over than $40^{\circ}C/sec$ for the dry film thickness over than 10 um. The heating efficiency of paint coated steels by the infrared heating was strongly dependent on the colors of paint coating and generally increased for the dark surface and/or coating. But the faster drying of the PCM resin coatings increased the blistering tendency of coating layer. The blistering limit for the typical finish coating by the infrared heating was estimated as the heating rate slower than $20^{\circ}C/sec$ regardless of colors of PCM resins.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.78-81
• /
• 2004

A technical performance of the coating depends greatly on the thickness of painting film or coating film. Therefore the confirmed report of the technique to measure accurately is essential to the coating film thickness for the assessment about a coating quality performance. In this paper, two gap sensors - eddy current gap sensor and capacitance gap sensor - which has a different operating principle were used to measure the thickness of a nonmagnetic substance coating film such as paint, enamel or ceramic that was coated on the metallic material. A capacitance gap sensor was used to measure the distance between the sensor head and a coating film and an eddy current gap sensor to measure the distance between the sensor head and a base metal. Then the thickness of a coating film was obtained by the difference of two measurement value. At this result, the suggested dual sensor can measure an arbitrary film thickness to be coated on a base metal as the measurement value of coating thickness exists accurately within the 2％ error.

• 대한조선학회논문집
• /
• 제47권5호
• /
• pp.743-749
• /
• 2010

Multi-nozzle spray painting procedure of the inorganic zinc shop primer was established in order to obtain uniform film thickness. The shop primer paint prevents the corrosion of steel block during shipbuilding. When the dry film thickness of shop primer is insufficient, rust will be generated on the steel block. Otherwise, thick coating of shop primer may be a problem of weld defect. So, it is important to obtain the uniform film thickness of shop primer. The uniformity of dry film thickness is affected by spray speed, distance from spray gun to target surface and overlapping span of spray path. In order to uniformly maintain coating thickness of shop primer, the coating procedure was established based on the correlation of shop primer spray variables.

• 한국기계가공학회지
• /
• 제7권4호
• /
• pp.68-75
• /
• 2008

This paper investigates the correlation between surface roughness and gloss of aluminium sheet painted waterborne paint. One customer criterion of automotive quality is the as-painted appearance of the final products. Especially, the current emphasis on control of surface roughness of sanded aluminium sheet has been prompted by the automotive industry's concern with the as-painted appearance. because the influence of such characteristics on paintability, and painted appearance is important in defining outer panel requirements for automobile. This paper is dedicated primarily to the issue of painted appearance and reviews for improvement of roughness. The conclusions are obtained as follows ; 1) Painted aluminium sheet appearance is strongly affected by surface roughness of base-metal and influenced by sand paper and sanding method. 2) The painted appearance of aluminium sheets was determined and related to surface roughness parameters, combination of sand paper.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.382-387
• /
• 2005

An electrochemical evaluation on the corrosion resistance for heavy anticorrosive paint was carried out for 5 kinds of heavy anticorrosive paints such as High solid epoxy(HE), Solvent epoxy(SE), Tar epoxy(TE), Phenol epoxy(PE), and Ceramic epoxy(CE) as parameters of DFT(Dry Film Thickness, 25${\mu}m$50${\mu}m$, solution condition(Flow of Nonflow). Corrosion current density of HE(DFT 50${\mu}m$ in case of flow condition was larger than that of nonflow condition. However, their values of the other anticorrosive paints were decreased compared to the nonflow condition. The values of AC impedance were increased with increasing of DFT regardless of kinds of anticorrosive paints. And the polarization resistance of cyclic voltammogram showed a good tendency to correspond with well the values of AC impedance measurement. HE and CE had a relatively good corrosion resistance than other heavy anticorrosive paint.

• 접착 및 계면
• /
• 제24권2호
• /
• pp.69-75
• /
• 2023

최근 자기복원(self-recovery) 코팅층을 가진 자동차용 도장면 보호필름의 적용이 증대되고 있다. 본 연구에서는 poly(urea-urethane) hybrid 자기복원 코팅층을 가진 poly(vinyl chloride) 기재 보호필름에 대한 기본 물성에 대한 평가 결과를 보고한다. Poly(urea-urethane) 기반 코팅층을 구성하고 있는 주요 화합물의 비율과 코팅층의 두께 변화에 따른 자기복원성능을 확인하였으며, 색차 값 측정을 통해 내오염성능을 정량화 하였다. 또한, 소수성 첨가제로 외부 오염에 대한 표면특성을 향상시키기 위하여, 소량의 실리콘계 반응형 첨가제를 코팅 조성물에 함량에 따른 easy-cleaning 효과와 접촉각을 확인하였다. 마지막으로, poly(urea-urethane) 자기복원 코팅층을 가진 보호필름의 장기간 사용에 따른 변색 및 변형에 대한 가능성을 확인하고자 촉진 내후성 평가를 진행하였다.