• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.377-380
• /
• 2003

Recently, demand of digital products with optoelectronic device is increasing rapidly. A microlens array is applied to improve optical efficiency on optoelectronic device, and it is usually fabricated by photolithography and reflow process after planarization layer coating process. UV molding process is more suitable for mass production of high quality microlens array than photolithography and reflow process. In the present study, microlens array was fabricated on the simulated optoelectronic device with planarization layer by aligned UV molding process. The shape of replicated microlens was measured, and the section image of molded part was examined.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1145-1150
• /
• 2005

The aim of this paper is to investigate the effect of surface texturing on metal surface and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 is recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.3
• /
• pp.94-99
• /
• 2011

Micro-scale surface pattern has an benefit of tribological application under lubricated sliding contact. Therefore, a special pattern, that has to reduce the coulomb friction under contact, is considered to be necessary for improved efficiency of machines. The current study investigated the friction property of angle effect for micro-scale grooved crosshatch pattern on bearing steel surface using pin-on-disk type. The samples fabricated by photolithography process and then these are carry out the electrochemical etching process. We discuss the friction property due to the influence of hatched-angle on contact surface. We could be explained the lubrication mechanism for a Stribeck curve. It was found that the friction coefficient depend on an angle of the crosshatch on contact surface. It was thus verified that micro-scale crosshatch grooved pattern could affect the friction reduction.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.17-24
• /
• 2004

Surrface texturing of tribological application is another attractive technology of friction reducing. Also, reduction of friction is therefore considered to be a necessary requirement for improved efficiency of machine. In this paper attempts to investigate the effect of density for micro-scale dimple pattern using photolithography on bearing steel flat mated with pin-on-disk. We demonstrated the lubrication mechanism for a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. It is found that friction coefficient is depended on the density of surface pattern. It was thus verified that micro-scale dimple could affect the friction reduction considerably under mixed and hydrodynamic lubrication conditions from based on friction map. Lubrication condition regime has an influence on the friction coefficient induced the density of micro dimple.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.59.2-59.2
• /
• 2011

We have demonstrated ink-jet printed indium tin oxide (ITO) and indium tin zinc oxide (IZTO) electrodes for cost-efficient organic solar cells (OSCs). By ink-jetting of crystalline ITO nano-particles and performing a rapid thermal anneal at $450^{\circ}C$, we were able to obtain directly patterned-ITO electrodes with an average transmittance of 84.14% and a sheet resistance of 202.7 Ohm/square without using a conventional photolithography process. The OSCs fabricated on the directly patterned ITO electrodes by ink-jet printing showed an open circuit voltage of 0.57 V, short circuit current of 8.47 mA/cm2, fill factor of 44%, and power conversion efficiency of 2.13%. This indicates that the ITO directly-patterned by ink-jet printing is a viable alternative to sputter-grown ITO electrodes for cost-efficient printing of OSCs due to the absence of a photolithography process for patterning and more efficient ITO material usage.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.369-372
• /
• 2008

Black matrix and Ag electrode with uniform line pitches were successfully fabricated through the photolithographic process by using the photosensitive black pastes and Ag pastes with optimized photosensitive properties for high resolution PDPs. The photosensitivity of the black and Ag pastes in the photolithographic process was investigated with the variation of photosensitive BM and Ag pastes and the photolithography process conditions. The important components and formulation of the photosensitive BM and Ag paste we discussed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.258-260
• /
• 2008

Developed halftone exposure technique was successfully applied to the fabrication of narrow transistor channels below $4\;{\mu}m$ with conventional photolithography method. Asymmetric slits concept of photo mask was applied to make channel lengths (L) shorter for thin film transistor's (TFT) high performance. These short channel TFTs verified better quality transistor characteristics.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.2
• /
• pp.236-240
• /
• 2013

In this presentation, we propose a fabrication method of PDMS stencil to apply into a localized culture of NIH/3T3 cells. PDMS stencil was fabricated by nitrogen gas blowing and soft lithography from preparing SU-8 master mold by photolithography. PDMS stencil pattern was production of the circle size 20 to $500{\mu}m$. In the culture test of PDMS stencil, a stencil was placed on a glass disk. The NIH/3T3 cells were successfully cultured into micropatterns by using the PDMS stencil. The results showed that cells could be cultured into micropatterns with precisely controlled manner at any shapes and specific size for bioscience study and bioengineering applications.

• Journal of Biomedical Engineering Research
• /
• v.30 no.6
• /
• pp.453-460
• /
• 2009

In this review paper, concepts in optofluidics are applied to an advanced manufacturing technology based on self-assembled microparts. The "optical" aspect of optofluidics will be described in the context of photolithography, and the "fluidic" aspect will be discussed in the context of self-assembly. First, optofluidic maskless lithography will be introduced as a dynamic fabrication method to generate microparticles in microfluidic channels. Next, the history and application of optofluidic lithography will be presented.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.165-166
• /
• 2006

Surface pattern of tribological applications is an attractive technology of engineered surface. Therefore, friction reduction is considered to be necessary for improved efficiency of machines. This study investigated the effect of friction property fur angles of micro-scale crosshatch grooved surface pattern on bearing steel flat mated with pin-on-disk. We obtain sample which can be fabricated by photolithography process. We discuss friction property depend on an angle of cross-hatch grooved pattern. We can verify the lubrication mechanism as a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter under the lubrication condition. It was found that the friction coefficient was related to angle of crosshatch on surface, even when surface pattern was the same density.