• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04b
• /
• pp.101-104
• /
• 2002

The beam splitter is important in optical communication systems. in this work, thc quasi-state based on four-mode interference in thc MMI coupler is proposed, and so, device length is shorten to be 1/5 of general designed length. We designed thc polarization splitter based on thc concept of quasi-state. Thc analysis has been accomplished by thc effective index method(EIM) and thc mode propagation analysis(MPA) for given structure.

• Current Optics and Photonics
• /
• v.7 no.2
• /
• pp.166-175
• /
• 2023

We theoretically analyze and experimentally demonstrate a polarization-diversified four-channel optical demultiplexer (DeMUX) comprising a hybrid mode conversion-type polarization splitter rotator (PSR) and delayed Mach-Zehnder interferometer optical DeMUX for use in coarse wavelength division multiplexing (CWDM)-based optical interconnect applications. The Si wire-based device fabricated by a complementary metal-oxide semiconductor-compatible process exhibited nearly the same filter spectral response irrespective of the input polarization state under the PSR. The device had an extremely low insertion loss of <1.0 dB, polarization-dependent loss of <1.0 dB, and interchannel imbalance of <0.5 dB, suppressing unwanted wavelength and polarization crosstalk from neighboring channels of <-20 dB at each peak transmission channel grid.

• Korean Journal of Optics and Photonics
• /
• v.14 no.6
• /
• pp.657-662
• /
• 2003

Optimum Hamming apodized acousto-optic 2${\times}$2 add/drop multiplexers, using SiO$_2$ film loaded acoustic waveguide with angular offset to the Ti:LiNbO$_3$ waveguide, were fabricated. The four-port device consists of two input waveguides, a polarization beam splitter (PBS), two polarization conversion/acoustooptic tuning waveguide sections, a second PBS and two output waveguides. Insertion loss <7.1 ㏈ has been obtained and side-lobe of -19 ㏈ for -32 ㎽ RF driving power has been realized. Add/drop performance has been confirmed and a linear tuning rate of 8.1 nm/MHz and a 3 ㏈ spectral width of -1.5 nm were demonstrated.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.12
• /
• pp.10-15
• /
• 2013

In this paper, we propose a Lyot-type optical fiber comb filter based on a polarization-diversity loop structure (PDLS), which has flat-top pass bands and multiwavelength switching capability. Generally, the PDLS can remove the dependency of the filter on input polarization. The proposed filter is composed of a polarization beam splitter, two half-wave plates (HWPs), and two polarization-maintaining fiber loops concatenated with a $60^{\circ}$ offset between their principal axes. By controlling two HWPs, it can operate in a flat-top band mode or a lossy flat-top band mode with an inherent insertion loss of ~3.49dB. In particular, flat-top bands can be interleaved in both modes, which cannot be realized in a Lyot-Sagnac comb filter based on a fiber coupler. Compared with Solc-type high-order comb filters with the same order, the proposed filter shows sharper transition between pass and stop bands.

• Korean Journal of Optics and Photonics
• /
• v.13 no.3
• /
• pp.228-234
• /
• 2002

We report theoretical investigation on the polarization selective coupling characteristics of a side-polished fiber directional coupler with a thin metal interlayer. Based on normal mode theory the coupling properties of the device under various structural conditions are analyzed. It is shown that the coupling strength between TE modes weakens rapidly with increase or metal interlayer thickness, whereas that between TM modes becomes stronger. The design conditions of the polarization splitter using the coupler to achieve high extinction ratio and low insertion loss are presented.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.5
• /
• pp.1-6
• /
• 2011

By incorporating a polarization-diversity loop configuration (PDLC), we have demonstrated inline conversion between transmission and reflection spectra of a fiber Bragg grating (FBG) without reconfiguration of the fiber filter structure. The proposed apparatus consists of a polarization beam splitter, an FBG, and two quarter-wave plates (QWP's). The inline conversion operation between transmission and reflection spectra of the FBG was performed by proper adjustment of QWP's within the proposed filter. The band rejection ratio and side-mode suppression ratio in transmission and reflection modes of the fabricated filter were measured as ~17.0[dB] and ~16.4[dB], respectively.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.430-436
• /
• 2006

Polarization-independent $Ti:LiNbO_3\;2{\times}2$ optical add/drop multiplexer for the 1550nm wavelength region is fabricated. The device consists of two input waveguides, two polarization beam splitters. two polarization conversion/electrooptic tuning waveguide sections, and two output waveguides. The single mode channel waveguides for both TE and TM polarizations are fabricated on a x-cut $Ti:LiNbO_3$substrate by Ti diffusion. Spectral section is based on phase-matched polarization conversion due to shear strain induced by a thick $SiO_2$ grating overlay film. An applied voltage tunes the device by changing the waveguide birefringence, hence the optical wavelength at which most efficient polarization conversion occurs. Tuning rate of 0.094nm/V with a maximum range of 17nm has been obtained. The nearest side-lobe is about 8.2dB. The FWHM is 3.72nm.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.4 no.2
• /
• pp.29-36
• /
• 2005

All-optical fiber-type $2{\times}32$ splitters for an Ethernet PON (passive optical network) were fabricated by using a FBT (fiber biconical tapered) process and the performance of the splitters was tested in upstream transmission of the EPON system. The $2{\times}32$ splitters was obtained by cascading $1{\times}4$ splitters fabricated by a conventional FBT process and showed -18 dB of insertion loss with 1.5 dB uniformity of output power at each channel and -0.1 dB of polarization dependent loss. The insertion loss variation was below 0.1 dB at the temperature range of $-40^{\circ}C\;to\;80^{\circ}C$. For upstream channel transmission test in the EPON system were a Zig board and a burst mode receiver. Zenko-made optical module was used for the burst mode receiver by adding functions of serializer/deserializer and clock data recovery, a Virtex II pro20 chipset and Vitesse VSC7123 were used in the Zig board for characterizing the burst mode and in the clock data recovery chipset, respectively. Startup acquisition lock time and data acquisition lock time were measured to be 670ns and 400ns, respectively, in the upstream channel transmission of the EPON system adapting the $2{\times}32$ splitter fabricated in this work.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.32-37
• /
• 2002

Passive polarization mode splitters at λ= 1.55 ${\mu}{\textrm}{m}$ were designed and fabricated based on Ti:x-cut LiNbO$_3$ single-mode optical waveguide and two-mode interference theory. The splitting ratio with waveguide width 8 ${\mu}{\textrm}{m}$, branching angle 0.55$^{\circ}$ and interfering length 470 ${\mu}{\textrm}{m}$ showed 16.18 dB, 21.25 dB for TE and TM input polarization modes, respectively. Polarization cross-talk of -16.28 dB and -21.28 dB for TE and TM modes was achieved. Total insertion losses of 2.24 dB/cm (TE) and 2.41 dB/cm (TM) were also measured. The devices operated nearly wavelength independently over a range or 30 nm.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.2
• /
• pp.11-19
• /
• 2016

By incorporating a polarization-diversity loop configuration, we have demonstrated the inline switching of transmission and reflection spectra of one of two short-period fiber gratings (SPFGs) with different resonance wavelengths without reconfiguring the filter structure. The proposed filtering apparatus consists of a fiber-pigtailed polarization beam splitter, two SPFGs, and three quarter-wave plates (QWPs). The proposed filter can independently choose the transmission or reflection spectrum of each SPFG through the appropriate adjustment of the orientation angles of the QWPs within the filter without additional optical switches and couplers. The average insertion loss, band rejection ratio, and side-mode suppression ratio of the fabricated filter were measured as ~4.59, ~17.88, and ~19.67dB, respectively.