• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2003년도 Proceedings of the international symposium on the fusion technology
• /
• pp.703-710
• /
• 2003

In the sub-surface environments, detection of the movement of contaminant substances and recharge of groundwater by rainfall are very important factors which contain porosity and effective porosity of porous media. In this paper, the applicability of permittivity methods and proposed dielectric mixing models (DDMs) are discussed. This study showed that the ratio of effective porosity to porosity of Toyoura and River sands were 0.856 and 0.843. From the relationships between the relative porosity and effective porosity, all measured values can be confirmed to outside the range to about 0.800 for Toyoura and River sands under all experiments by FDR and FDR-V systems. In the study, this permittivity equipment can be considered to be good enough to measure determining the physical parameters of saturated soils. Consequently, this permittivity method can be contributed to estimate a porosity and effective porosity of saturated porous media because it is easy and instantaneous than previous in-situ methods.

• 한국건설순환자원학회논문집
• /
• 제5권4호
• /
• pp.421-426
• /
• 2017

본 연구에서는 초음파 속도 측정 실험을 이용하여 동결 융해 작용을 받는 시멘트 모르타르의 동탄성 계수 및 공극 구조 변화를 평가하기 위한 연구를 수행하였다. 초음파 속도는 동결융해 시험 중 매 30cycle마다 시편을 꺼낸 후 측정하였으며, MIP를 이용한 porosity 분석도 수행하였다. 초음파 속도 측정 결과를 이용하여 동탄성계수를 계산한 결과 300cycle 이후 약 13%가 감소하는 것으로 나타났다. porosity는 초기에 대비해서 약 30%가량 증가하였으며, 초음파 속도 측정으로부터 계산된 porosity는 MIP를 통해 측정한 porosity와 약 5~30% 차이를 보였지만 유사한 증가 경향을 보이는 것으로 확인되었다. 이를 통해 초음파 속도 측정 결과를 이용하여 시멘트 모르타르의 porosity 변화를 예측하는 것은 타당한 방법으로 볼 수 있으며, 이를 이용하여 확산계수 등 내구성 평가 지수를 예측할 수 있는 것을 확인할 수 있었다.

• 보존과학연구
• /
• 통권31호
• /
• pp.31-42
• /
• 2010

This study were performed thermal shock test for four kind of different rocks (Iksan granite, Namsan granite, Jeongseon marble, Yeongyang sandstone), and according to heating temperature($400^{\circ}C$, $600^{\circ}C$) on samples were investigated physical properties such as specify gravity, porosity, p-wave velocity. As a result, the tendency was appeared that porosity increased, and specific gravity and p-wave velocity decreased at a more higher temperature. But, the situation of change appeared characteristic according to temperature and rock types. In the case of Yeongyang sandstone, it appeared in especially porosity increasing at $400^{\circ}C$. The specific gravity was little change in the all the rock at $400^{\circ}C$ but the decreased at $600^{\circ}C$. Therefore the specific gravity in the temperature range is due to the relatively small impact on the change is expected. Porosity of the granite at $400^{\circ}C$ changes little. but marble in the rate of change is large. Conversely, the sandstone porosity decreased. At $600^{\circ}C$ increased porosity in all of rocks. particularly sandstone the smallest increase in porosity. Experiments showed that p-wave velocity measured through dry rocks was sensitive to quantify the thermal damage. The p-wave velocity of all rocks decreased with increasing temperature. In the relation between porosity and p-wave velocity, p-wave velocity decreased with increasing porosity. On the other hand, in case of Yeongyang sandstone p-wave velocity decreased with decreasing porosity. thus, development of microcracks more affects p-wave velocity than porosity. In this study, damage intensity was well explained with porosity and p-wave velocity values depending on temperature increase.

• Steel and Composite Structures
• /
• 제49권6호
• /
• pp.713-728
• /
• 2023

This paper aims to investigate the free vibration analysis of FG plates, taking into account the effects of even and uneven porosity. The study employs the Hellinger-Reisner functional and obtains the element's bending stress and membrane stress fields from the analytical solution of the governing equations of the thick plate and plane problem, respectively. The displacement field serves as the second independent field. While few articles on free vibration analysis of circular plates exist, this paper investigates the free vibration of both rectangular and circular plates. After validating the proposed element, the paper investigates the effects of porosity distributions on the natural frequency of the FG porous plate. The study calculates the natural frequency of thin and thick bending plates with different aspect ratios and support conditions for various porosity and volume fraction index values. The study uses three types of porosity distributions, X, V, and O, for the uneven porosity distribution case. For O and V porosity distribution modes, porosity has a minor effect on the natural frequency for both circular and rectangular plates. However, in the case of even porosity distribution or X porosity distribution, the effect of porosity on the natural frequency of circular and rectangular plates increases with an increase in the volume fraction index.

• 한국주조공학회지
• /
• 제37권6호
• /
• pp.193-198
• /
• 2017

In this study, volumes of shrinkage and porosity of A356.2 alloys during casting were analyzed as a function of melt temperature, pouring diameter, mold temperature, and Sr content. The temperature of the melt barely affected the shrinkage and porosity formation. The pouring diameter determined the pouring rate, and it was proportional to the shrinkage, yet no relationships with the density of porosity were observed. When the mold was heated at $400^{\circ}C$, shrinkage and porosity in the alloy increased above the one in the mold without heating. However, the mold without heating experienced interior shrinkage and the porosity was mainly distributed near interior shrinkage. The addition of Sr to the melt resulted in more shrinkage and less porosity.

• 한국세라믹학회지
• /
• 제35권9호
• /
• pp.988-994
• /
• 1998

In the manufacturing of vitreous bonded CBN tool the porosity change associated with various processing conditions, I. e. the sintering temperature and the size and the amount of abrasive grits was observed. In the case of sintering of vitreous bond material only the specimen density reached the maximum at 950$^{\circ}C$ and then the total porosity was increased slightly with the temperature above 950$^{\circ}C$. In the sintering of a-brasive grits and the vitreous bond material together a marked increase in the total porosity was found with the temperature above 950$^{\circ}C$ Reducing the grit size at the constant volume fraction of abrasive grits showed an increase in the total porosity at whole sintering temperature. On the contrary. it was observed that increasing the volume fraction of abrasive grits with a same size showed the increased open porosity simultaneously with decreased closed porosity at whole sintering temperature.

• 한국기계가공학회지
• /
• 제6권2호
• /
• pp.9-16
• /
• 2007

The fatigue test of the fillet weldments were executed with different groove angles and porosity. The groove angles of $90^{\circ}$, $45^{\circ}$ and $55^{\circ}$ were compared with fatigue lives. After the fillet weldment failure, the porosity which found at the fractured surface were observed to account the effect on fatigue life. Finite element analysis were performed to correlate the fatigue strength and the size & the location of porosity. The stress-strain field were severely affected by the length of notch and the size & location of porosity. Based on the quantitative analysis of porosity effect, the total volume of porosity was key factor for fatigue strength of the fillet weldment.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.691-694
• /
• 2005

The present study was to examine the influence of porosity and moisture content on the water permeability, strength and plant-growth characteristics of porous concrete. The result of the experiment verified that the coefficient of permeability of porous concrete with porosity between $30\%\;and\;36\%$ increased by 2cm/sec and the compressive strength decreased 1MPa at every $3\%$ increase of porosity. In addition, the plant growth of porous concrete showed 5cm at $36\%$ porosity and 2.5cm at $30\%$ porosity respectively. Thus, the higher the porosity, the more the plant grew. When $2\%$ moisture content was used in porous concrete with the same porosity, the plant growth was accelerated two times faster than the case without it.

• Earthquakes and Structures
• /
• 제16권5호
• /
• pp.601-609
• /
• 2019

The effect of the porosity and its distribution shape on the normal and shear interfacial stresses of the FGM beam strengthened with FRP plate subjected to a uniformly distributed load are investigated analytically in the present paper. Basically, the governing equations of FGM beams with porosity strengthened with composite plates are identical to the ones without porosity. Nonetheless, when the effect of the porosity and its distribution shape are taken into account, the rule of mixture was reformulated to assess the material characteristics with the porosity phases and its distribution shape. This work discusses the influence of the gradient index, the porosity and its distribution shape on the interfacial stresses.

• 지질공학
• /
• 제14권2호
• /
• pp.169-177
• /
• 2004

포화 및 불포화 상태로 이루어진 지반 내에서 지하수의 함량 및 오염물질의 침투 이동은 지반을 구성하고 있는 다공질 매질의 공극률과 유효공극률에 매우 큰 영향을 받는다. 본 연구는 불포화 매질에 대한 유효공극률을 측정하기 위해서 Frequency domain reflectometry(FDR) system 및 측정센서를 개발하여 실내실험을 수행하였다. 또한 측정된 유전율상수의 관계로부터 유효공극률을 산정할 수 있는 유전을 믹싱모델(dielectric mixing model)을 제안하였다. 실험결과에서 불포화 흙 시료인 표준사(standard sand)와 강모래(river sand)의 유효공극률의 범위는 공극률과 비교해 약 65∼85% 내외에서 측정되었다. 특히, 측정된 유효공극률과 공극률의 관계에서 공극률이 증가할수록 유효공극률은 다소 감소하는 경향을 보이는 것으로 측정되었다. 이는 흙 입자사이의 공극 내에 존재하는 미량의 공기에 의한 것으로써 불포화 상태의 흙 칼럼이 충분히 포화 상태에 도달하지 못하였기 때문이다.