• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.754-761
• /
• 2008

In general, stress measurement of existent shotcrete lining be used by pressure cells. but, measuring instrument is lost by high pressure at shotcrete lining construction and pressure cell's measurement value have to low believability by natural conditions like curing temperature. In this study, proposed techniques to measure without utilizing sensitive stress sensor in natural condition at point that want stress of shotcrete lining after shotcrete lining construction. Executed numerical analysis to forecast stress level that interact in tunnel shotcrete lining, measured strain of hole by load action through hole in shotcrete lining. 3D FEM(finite element method) is enforced through various parameters curing time of shotcrete lining, thickness, load condition. Different model cases applied by parametic study. As analysis result, it could grasp development possibility of method that propose this time because it could examine corelation with strain by near hole of shotcrete lining and stress about load condition.

• Carbon letters
• /
• 제6권3호
• /
• pp.181-187
• /
• 2005

Bipolar plates require some specific properties such as electrical conductivity, mechanical strength, chemical stability, and low permeability for the fuel cell application. This study investigated the effects of carbon nanotube (CNT) contents and process conditions of hot press molding on the electrical and physical properties using CNT 3~7 wt% added graphite nano-composites in the curing temperatures range of 140~$200^{\circ}C$ and pressure of 200~300 kg/$cm^2$. Bulk density, hardness and flexural strength increased with increasing CNT contents, curing pressure and temperature. With the 7 wt% CNT added noncomposite, the electrical resistance improved by 30% and the flexural strength increased by 25% as compared to that without CNT at the temperature of $160^{\circ}C$ and pressure of 300 kg/$cm^2$. These properties were close to the DOE reference criteria as bulk resistance of 13 $m{\Omega}cm$ and tensile strength of 515 kg/$cm^2$.

• 한국축산식품학회지
• /
• 제37권4호
• /
• pp.477-485
• /
• 2017

Novel, effective methods to control and prevent spoilage and contamination by pathogenic microorganisms in meat and meat products are in constant demand. Non-thermal pasteurization is an ideal method for the preservation of meat and meat products because it does not use heat during the pasteurization process. Atmospheric pressure cold plasma (APCP) is a new technology for the non-thermal pasteurization of meat and meat products. Several recent studies have shown that APCP treatment reduces the number of pathogenic microorganisms in meat and meat products. Furthermore, APCP treatment can be used to generate nitrite, which is an essential component of the curing process. Here, we introduce the effectiveness of APCP treatment as a pasteurization method and/or curing process for use in the meat and meat product processing industry.

• 폴리머
• /
• 제24권5호
• /
• pp.690-700
• /
• 2000

본 연구에서는 온도의 상승에 의하여 부피가 팽창하는 열팽창 고무 치공구의 팽창 특성을 이용하여 열경화성 복합재료를 경화하고 압축하는 과정을 실험과 모델링을 통하여 해석하였다. 열팽창 고무치공구가 사용되는 닫힌계 (fixed-volume process)와 열린계 (variable-volume process)에서 예상되는 압력을 이론적으로 유도하였고, 경화가 수반되는 과정에 있어서는 실험을 통하여 열팽창 치공구와 프리프레그가 나타내는 압력을 측정하였다. 온도가 상승하고 경화가 수반되는 경우에 등속도 압축실험에 의하여 얻어진 응력-변형율 곡선은 비선형 점탄성 특성을 보여주었는데, 본 연구에서는 Maxwell모델을 KWW (Kohlrausch-Williame-Watts)식으로 변형시킨 모델식을 이용하여 이를 매우 정확하게 표현할 수 있었다. 이 모델을 이용하여 몰드의 부피를 고정시킨 상태에서 경화시키는 닫힌계 공정에서 예상되는 압력을 예측하였으며 따라서 열팽창 치공구를 열경화성 복합재료의 경화압축 공정에 성공적으로 적용하였고 이를 해석하였다.

• Composites Research
• /
• 제32권5호
• /
• pp.199-205
• /
• 2019

복합재는 원하는 방향으로 섬유를 배열하여 일체형으로 제조할 수 있는 장점이 있다. 그러나, 복합재는 제작과정에서 층(ply)과 층 사이에 있는 미세 공기, 소재 내부의 수분 또는 경화 중의 부적절한 온도와 압력 등으로 인하여 미세기공이 형성될 수 있으며, 이는 복합재 부품의 기계적 강도저하의 주요 원인으로 평가되고 있다. 본 논문에서는 오토클레이브 진공백 성형법을 이용하여 복합재 두께 별로 공정 조건(경화압력, 압밀시간, 압밀압력, 진공압력)을 변화시켜가며 복합재 패널을 제작하여 미세기공률을 분석하였다. 미세기공률은 이미지 분석법, 용해법, 연소법을 이용하여 평가하였으며, 초음파 감쇠계수와의 연관성을 분석하였다. 실험결과, 미세기공률 분석의 정확도는 용해법이 가장 우수한 것으로 나타났으며, 경화압력이 낮아질수록 미세기공률이 증가하고 높은 초음파 감쇠계수 값을 가짐을 확인하였다. 또한, 동일한 경화압력이라도 적층두께가 증가할수록 초음파 감쇠계수가 증가하고 기공률이 증가됨을 확인하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 춘계 학술논문 발표대회
• /
• pp.34-35
• /
• 2019

In recent years, the construction industry has also applied the dry method that can be assembled in the field by industrialization and factory production, which is free from climatic effects and can reduce the cost due to mass production and simplify the work in the field. Among the building materials used in this dry method, ALC products are made by mixing calcium oxide, gypsum, cement, and water in silica and putting them in an autoclave to create voids in the interior through steam curing at high temperature and pressure. But it requires curing cycle conditions of warming, isothermal, and temperature curing. It depends on the performance of the product depending on the curing conditions, the economical efficiency due to high oil prices, the emission of greenhouse gases by the use of fossil fuels. Experiments were conducted to select an appropriate animal protein foam for lightweight foamed concrete block which was cured by applying a prefilling method to replace existing ALC products. As a result of investigating the characteristics of lightweight foamed concrete by type of animal protein foam, it is considered that FP3 is most suitable for manufacturing lightweight foamed concrete block.

• Advances in concrete construction
• /
• 제8권2호
• /
• pp.139-144
• /
• 2019

In this study, the mechanical properties of reactive powder concrete (RPC) with a constant cement to silica fume ratio of 4 were investigated. In the experimental program, reactive powder concretes with steel fiber at different ratios were produced. Five productions using quartz sand with a maximum grain size of 0.6 mm were performed. A superplasticizer with a ratio of 3% of the cement was used for all productions. $40{\times}40{\times}160mm$ prismatic specimens were prepared and tested for flexural and compression. The specimens were exposed to two different curing conditions as autoclave and standard curing condition. Autoclave exposure was performed for 3 hours under a pressure of 2 MPa. It was observed that the compressive strength of concrete, along with the flexural strength exposed to autoclave was quite high compared to the strength of concretes subjected to standard curing. The results obtained indicated that the compressive strength, along with the flexural strength of autoclaved concrete increased as the amount of cement used increases. Approximately 15% increase in flexural strength was achieved with a 4% steel fiber addition. The maximum compressive strength that has been reached is over 210 MPa for reactive powder concrete for the same steel fiber ratio and with a cement content of $960kg/m^3$. The relationship between compressive strength and flexural strength of reactive powder concrete exposed to both curing conditions was also identified.

• Composites Research
• /
• 제23권2호
• /
• pp.31-39
• /
• 2010

본 논문에서는 모자(Hat)형 보강구조를 가진 복합재 패널을 일체성형(Co-curing), 동시접착(Co-bonding), 이차접착(Secondary bonding)의 세 가지 공법으로 제작하였다. 일체성형은 별도의 접착제 없이 프리프레그 상태의 외피와 보강재를 만들어 함께 성형하는 방법으로 다른 제작 공법에 비해 별도의 조립공정이 불필요한 경제적인 공법이다. 동시접착은 외피와 보강재 중 하나를 먼저 성형하고, 나머지는 프리프레그 상태로 먼저 성형된 구조물과 함께 성형하는 방법이며, 이차접착은 복합재 외피와 보강재를 각각 별도로 제작한 후 이를 접착제를 이용하여 별도로 접착하는 방법이다. 일체성형으로 보강 패널을 제작하는 공정에서는 경화 후 내부 금형의 제거를 용이하게 하기 위한 고무금형을 설계, 제작하였고, 경화 온도로 인해 고무금형에서 발생하는 팽창압력에 대한 유한요소해석을 수행하였다. 제작된 보강 패널은 3-D 측정 장비와 초음파 장비로 치수정밀도 및 내부 결함을 평가하였으며, 직접인장시험(Pull-off test)을 수행하여 기계적 특성을 평가하였다.

• Elastomers and Composites
• /
• 제34권4호
• /
• pp.321-331
• /
• 1999

타이어 가황공정(curing process)은 타이어 제조를 위한 최종공정으로 여러 개의 고무배합물 층으로부터 성형된 그린타이어(green tire)를 가황기(mold)내에서 고압/고온 조건하에 유지시킴으로써 원하는 형상을 얻게 하고, 아울러 각 고무배합물이 고탄성을 갖도록 물성을 변화시키는 공정이다. 본 연구에서는 타이어 품질의 향상을 위해 가황공정을 수치적으로 최적화하는 기법을 개발하였다. 먼저, 가황공정 중 가황매체(cure media)의 최적공급 조건을 경정하기 위해 제약조건을 갖는 동적최적화문제(dynamic constrained optimization problem)로 정형화하였다. 즉, 가황기 내의 전열 및 가황 반응 현상을 묘사하는 공정모델로 표현되는 등위제약조건(equality constraint)과 가황매체가 갖는 온도의 한계를 표현하는 부등위제약조건(Inequality constraint) 아래 목적함수를 최적화 시켰다. 다음, 공급되는 가황매체의 최적조건을 결정하기 위해 구성된 최적화문제를 유한요소법(FEM)과 complex 알고리즘을 적용하여 풀었다.

• 대한치과기공학회지
• /
• 제33권1호
• /
• pp.25-35
• /
• 2011

Purpose: There are some advantages of the acrylic resin denture base ; appropriate strength, volume safety, simple processing apparatus, and low cost. But, it have a weakness for fracture by intense pressure or shock. However, the repairs for resin denture base are possible using various materials and techniques. There is a few studies in repairs for resin denture base, but not clinical researches. And there is no studies in absorbed saliva into the region of fracture and bond strength. This study is to observe re-bond strength of resin denture base after repairing under saliva absorption. Methods: The samples were made of heat curing resin and the rectangular parallelepiped specimens which were 50mm long, 10mm wide and 3mm high. The four different groups immersed in the artificial saliva for 2 weeks were prepared, 1) no repaired control samples, 2) immediately repaired samples, 3) repaired samples after 1 day dry, and 4) repaired samples after 3 days dry. The prepared samples were repaired by two different curing materials, self curing resin and heat curing resin method. Each groups composed of 10 specimens were experimented with the three point bending tests for bonding strength measuring Results: There were under condition absorbed in the artificial saliva and repaired by self curing resin method, repaired specimens after 1 day and 3 days dry groups had higher values of bonding strengths than control group, and bonding strengths of immediately repaired samples were similar to those of control samples (p<0.05). There were under condition immersed in the artificial saliva and repaired by heat curing resin method, immediately repaired samples showed similar values to bonding strengths of control groups, and repaired samples after 1 day and 3 days dry groups were lower than those of control group (p>0.05). Conclusion: In this study, the repairs for resin denture base were remarkably high values of bonding strengths than those of the past, and showed that have stable bonding strengths independent of saliva absorption of denture base, so present repairs for resin denture base can be performed, regardless of saliva conditions.