• Elastomers and Composites
• /
• v.51 no.2
• /
• pp.106-112
• /
• 2016

Maleimidopropyltriethoxysilane grafted natural rubber (MISNR) was prepared by reaction of maleic anhydride grafted natural rubber and 3-aminopropyl triethoxysilane. MISNR was used as the compatibilizer of natural rubber/silica composites. The composites were prepared by two-step mixing procedures. The final mixtures were cured with optimum cure condition, which was established by a rheometer. Effects of the amounts of compatibilizer in the composites on the cure characteristics, morphology, thermal stability, and physical and mechanical behaviors were investigated. The composites having MISNR had shown cure characteristics and physical and mechanical properties superior to those without MISNR. Silica particles in the former appeared to be more uniform and reduced in size compared with the latter. The effects of the types of silica were also evaluated.

• Fibers and Polymers
• /
• v.5 no.4
• /
• pp.270-274
• /
• 2004

Blends of poly(l-lactide) (PLA) and low density polyethylene (LDPE) were prepared by melt mixing in order to improve the brittleness of PLA. A reactive compatibilizer with glycidyl methacrylate (GMA), PE-GMA, was required as a compatibilizer due to the immiscibility between PLA and LDPE. It contributes to reduce the domain size of dispersed phase and enhance the tensile properties of PLA/LDPE blends, especially for PLA matrix blends. A reaction product between PLA and PE-GMA, which was formed during melt-mixing and considered to act as a reactive compatibilizer, was characterized using $ ^1H-NMR$ spectroscopy.

• Textile Coloration and Finishing
• /
• v.24 no.2
• /
• pp.145-151
• /
• 2012

Polymer alloys of poly(ethylene terephthalate)(PET) and nylon6(PA6) which were not miscible each other by themselves were successfully prepared through melt compounding using a twin-screw extruder by utilizing epoxy as reactive compatibilizer. At the epoxy(DGEBA) amount of 0.5~2wt%, the domain size(average diameter) of the discontinuous phase could be reduced up to 0.2${\mu}m$ from 1-5${\mu}m$ that of the simple blend without epoxy. The reaction was presumed to happen mostly at interphase from the result of maximum increase of melt viscosity at the middle range of PET/PA6 blend ratio. It is expected that alloy fibers of PET/epoxy/PA6 with enough mechanical strength for use can be prepared.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.71-79
• /
• 2002

RPP(maleic-anhydride grafted PP)and OPS(oxazoline grafted PS) do not react to each other, and thus show immiscibility. In this study, Nylons was added to RPP/OPS blend systems, as a reactive compatibilizer for enhancing the miscibility of the blends. When Nylon6 was added to the blends of RPP and OPS, RPP/Nylon6/OPS was produced. The effects of the molar ratio of Nylon6 on the RPP-Nylon6-OPS reaction were studied. Torque test and FT-IR analysis have been carried out to investigate the reaction of RPP/Nylon6/OPS system. The reaction torgue ratio and reaction efficiency show the maximum values at 1 : 0.66 : 1 and 1 : 1 : 1 (in moles) for RPP/Nylon6/OPS. In the RPP/Nylon6/OPS blends, their mechanical properties were changed with the molar ratio of Nylon6 and showed the highest value at molar ratio of 1.5. Physical properties and compatibility of RPP/Nylon6/OPS were compared with those of PP/Nylon6/OPS. Consequently, RPP/Nylon6/OPS plays a proper role as a reactive compatibilizer to the PP/PS blend system.

• Polymer(Korea)
• /
• v.37 no.4
• /
• pp.500-506
• /
• 2013

The effect of compatibilizer types on the properties of polyphenylene sulfide (PPS)/polyethylene terephthalate (PET) blends was investigated. The blends were extruded by a single screw extruder attached with a Maddock mixing zone and their molded properties were examined. As a basic blend composition, a linear PPS/PET (40/60) blend was selected based on cost efficiency. Three types of compatibilizer, SEBS, modified SEBS, and modified PS were added to the basic blend to improve the properties. The thermal, rheological, mechanical properties and the morphology of the ternary blends were analyzed. The maximum mechanical properties of blends was found at 1 phr of m-SEBS or m-PS content, whose values were almost the same as the theoretical values of miscible blend system. It seemed to by the case that the partial reaction between compatibilizer and the basic blend caused the enhancement of compatibility between linear PPS and PET phases. These ternary blends would be applicable as economic linear PPS alloys.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.10a
• /
• pp.448-451
• /
• 2001

각각 소수성과 친수성을 나타내는 올레핀계 고분자인 PE 와 granule starch의 blend는 서로 다른 특성에 기인하여 거시적인 상분리 현상이 발현되며 두 물질간에 계면을 형성한다. 이와 같이 낮은 interfacial adhesion을 갖는 내부 구조는 외력에 대한 저항력이 급격히 저하되어 낮은 물성 특성을 나타낸다. (중략)

• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.189-195
• /
• 2015

In this study, we prepared epoxidized poly ethylene-ter-1-decene-ter-divinylbenzene (Epo-PEHV) as a reactive compatibilizer to prevent phase separation phenomenon which occurs upon blending polypropylene (PP) and ethylene-vinyl alcohol copolymer (EVOH). Firstly, PEHV was prepared under high catalyst activity according to content of catalyst and cocatalyst. After then, we modified vinyl group of the terpolymer with epoxy group. We observed that the terpolymer was successfully epoxidized by 1H-NMR and FT-IR analysis. The Epo-PEHV was added by 2, 5, 10% in PP/EVOH blends. The morphologies and mechanical properties of PP/Epo-PEHV/EVOH blends were analyzed by SEM and UTM, respectively. Epo-PEHV enhanced the interfacial adhesion of PP and EVOH blends.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.490-495
• /
• 2009

The reactive compatibilization of amorphous poly-${\alpha}$-olefins (APAO)/amorphous polyamide (aPA) blends was carried out using two kinds of reactive compatibilizers such as maleated polypropylene and ethylene-glycidyl methacrylate-methyl acrylate copolymer. The grafting reaction rates between aPA and the compatibilizers were examined using FT-IR, SEM and rheometer. The effect of the reactive compatibilization on the mechanical property of the blends was investigated with a universal testing machine. The adhesion strength of the blends including a hydrocarbon tackifier resin, C9 was also measured.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.19-24
• /
• 2005

Polymer blends containing polypropylene (PP) with compatibilizers were prepared using twin screw extruder. Physical properties were investigated using universal test machine (UTM) and Izod impact tester. In the PP/acrylonitrilebutadiene-styrene (ABS) blends, mechanical strength was increased with the addition of PP-g-styrene acryloritrile (PP-g-SAN) compatibilizer, and the ductility was increased with the addition of ethylene-ethyl acrylate-maleic anhydride (E-EAMAH-g-SAN) compatibilizer. For the PP/ABS/ polycarbonate (PC)/Nylon-6,6 blends, impact strength was increased with the addition of ethylene glycidylmethacrylate (E-GMA compatibilizer) up to 0.5 phr. In the case of the PP/ABS/PC/Nylon-6,6/poly(methyl methacrylate) (PMMA)/poly(oxymethylene) (POM)/poly(vinyl acetate) (PVC)/poly(butylene terephthalate) (PBT) blends, mechanical properties were increased by the complex compatibilizing effects of PP-g-SAN, E-EA-MAH-g-SAN and E-GMA, respectively.

• Polymer(Korea)
• /
• v.27 no.4
• /
• pp.285-292
• /
• 2003

The compatibility of poly(lactic acid)/poly($\varepsilon$-caprolactone) (PLA/PCL) blends as a function of blend composition was studied and triphenyl phosphite (TPP) was applied to PLA/PCL blends as a reactive compatibilizer. Especially the effect of compatibility on the crystallization behavior in both PLA/PCL blends and PLA/PCL blends with TPP was considered. PLA/PCL blends were immiscible based on thermal characteristics of PLA/PCL blends and the miscibility was depend upon the blend composition. The enhancement of compatibility was found in PLA/PCL blends with TPP depend upon its content. The rate of crystallization in PLA/PCL blend varied with blend composition. This was understood as the development of nucleation at the interface of PLA-PCL due to the immiscibility. TPP was acting as a compatibilizer as well as an agent for the acceleration of spherulite growth In PLA. As a result, the crystallization rate increased and the size of spherulite became larger than that of PLA/PCL blend without TPP.