• Journal of the Korea Concrete Institute
• /
• v.29 no.3
• /
• pp.275-281
• /
• 2017

This study examined the effect of water-to-binder ratio (W/B) and phosphate-to-binder ratio (P/B) on the flow, setting time, compressive strength development, and pH variation of magnesium-potassium phosphate composites, MKPC mortars. Ten mortars mixtures were prepared with the W/B varying from 20% to 40% at each P/B of 0.3 or 0.5. The hydration products and microstructural pore distribution of the MKPC pastes were investigated using X-ray diffraction (XRD), scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). The initial flow and setting time of MKPC mortars tended to decrease with an increase of P/B, indicating that the final setting time was shortened by approximately 24% when P/B increased from 0.3 to 0.5. The slope of the early-strength development measured in the MKPC mortars was considerably higher than that of cement concrete specified in code provisions. For obtaining a relatively good 28-day strength (above 30 MPa) and a near neutral pH (below 9.0) in MKPC mortars, the P/B and W/B need to be selected as 0.5 and 30%, respectively. The strubite-K crystal increased with the increases of P/B and W/B, which leads to the decrease of the macro-capillary pores.

• The Korean Journal of Malacology
• /
• v.28 no.2
• /
• pp.157-164
• /
• 2012

The patterns in X-ray diffraction (XRD) spectroscopy provide useful clue at $29.4^{\circ}$ to discriminate two types of Akoya cultured pearl which occurs difference of surface luster. Using the optical microscope, we could be confirmed that the nareous layer of each sample consist of different crystal form. In Fourier Transform Infrared (FT-IR) Spectroscopy analysis, the nareous layer of Akoya cultured pearls with poor luster shows some peaks at 712, 699, 1435, $1444cm^{-1}$ region and these peaks depend on the Calcite. But the nareous layer of pearls with excellent luster could not observed those peaks related with Calcite, we could observed Aragonite band at 699, $1085cm^{-1}$ region. Though this result, we know that the nareous layer of Akoya cultured pearls with excellent luster is mainly composed by Aragonite. Raman bands are also clearly demonstrated to occur difference of band intensity by difference of Aragonite content. In the Scanning Electron Microscope (SEM) analysis, we found that the Akoya cultured pearl luster and surface condition is associated with internal structure.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.2
• /
• pp.77-87
• /
• 1996

The estimation of the remaining life for the aged components in power plant as well as chemical and peroleum plants has been recently coberned. The raw materials used in this syudy are the 1Cr-1Mo-0.25V rotor steel which intensified P and S compositions along with the nominal compositions of ASTM A470 standard. Five kinds of specimens with the different degradation levels were prepared by isothermal aging teat treatment at $630^{\circ}C$ The mechanical properties and fatigue strength of virgin and aged 1Cr-1Mo-0.25V rotor steel have been inbestigated through the hardness, tensile, fatigue test, SEM fractograph and EDS analysis at room temperature. Thus, the data of aged specimens were compared with those of virgin specimen to evaluate the aging effects. The main results obtained in this study are as follows; The decrease of the hardness due to degradation was distinguished until 50, 000hrs simulated service time. And is was confirmed that the considerable amount of P, Mn, Cr and S was precipitated at the grain boundary of aged material through the SEM and EDS analysis. The fatigue strength of 25, 000, 50, 000, 75, 000 and 100, 000hrs aged material was decreased 29.5%, 24.4%, 28.6%, 35.7% than that of virgin material at $10^7$ cycles of room temperature. The major cracks of virgin and aged materials initiated at the inclusions including Si, P and Mn compositions which were located at the outer periphery of the specimen.

• Journal of dental hygiene science
• /
• v.22 no.1
• /
• pp.20-29
• /
• 2022

Background: The purpose of this study is to investigate the effect of liquefied digestive medicines on the composite resin surface. Methods: Three types of liquefied digestive medicines (Gashwalmyeongsu, Wicheongsu, and Saengrokcheon) were selected as experimental groups, Samdasoo and Chamisul as negative controls, and Trevi as positive controls were selected to measure pH and titratable acidity. The samples filled with resin at acrylic were made total 300, 50 per group. To evaluate the erosion risk of the composite resin, the specimens were immersed in a liquefied medicine for 1, 3, 5, 15, and 30 minutes, and then the surface microhardness was measured using the Vickers Hardness Number, and the surface change was observed with scanning electron microscope (SEM). Results: The average pH of the three liquefied medicine was 3.75±0.30, the Saengrokcheon was the lowest at 3.45±0.01, and the Trevi was 4.66 and Samdasoo and Chamisul were 7.40 and 8.58, respectively. The amount of NaOH reaching pH 5.5 and 7.0 was the lowest in the order of Trevi, Gashwalmyeongsu, Wicheongsu, and Saengrokcheon. The largest surface hardness reduction value was shown in Gashwalmyeongsu (-11.85±3.73), followed by Saengrokcheon (-9.79±3.11) and Wicheongsu (-8.28±2.83), and Samdasoo (-0.84±1.56) and Chamisul (-6.24±0.42) had relatively low surface hardness reduction values. However, Trevi (-16.67±5.41), a positive control group containing carbonic acid, showed a higher decrease in surface hardness than the experimental group. As a result of observation with SEM, experimental group and positive control group, showed rough surfaces and irregular cracks, and negative control groups showed smooth patterns similar to before immersion. Conclusion: The liquefied digestive medicine with low pH could weaken the composite resin surface, and the carbonic acid component could more effect on the physical properties of the composite resin than pH.