• KNOM Review
• /
• v.24 no.2
• /
• pp.35-47
• /
• 2021

Various stress exists in a modern society, which requires constant competition and improvement. A person under stress often shows his pressure in his facial expression and language. Therefore, it is possible to measure the pressure using facial expression and language analysis. The paper proposes a stress measurement system using facial expression and language sensitivity analysis. The method analyzes the person's facial expression and language sensibility to derive the stress index based on the main emotional value and derives the integrated stress index based on the consistency of facial expression and language. The quantification and generalization of stress measurement enables many researchers to evaluate the stress index objectively in general.

• International conference on construction engineering and project management
• /
• 2007.03a
• /
• pp.625-634
• /
• 2007

Energy-saving is one of important issues in multi-family housing projects in South Korea. According to the study by Yu et al. (2002), the balcony conversion causes energy loss approximately one and a half times. Therefore, it is important to select the economical glass type in the balcony window. In order to identify the most economical glass type of balcony conversion in multi-family housing projects, the most typical type of the multifamily housing projects in the metropolitan area was selected as a candidate project. The selected candidate project has been simulated using ENERGY-10 program to estimate the heat load by the different five types of glasses as well as their life cycle cost analysis (LCCA) using present worth method. Finally, sensitivity analysis has been conducted to determine the most economical glass types under a different discount rate (interest rate) and service life of building.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.329-332
• /
• 2008

Nowadays, It is required human body-friendly, good mechanical properties, and economical efficiency material, simultaneously. The material to meet above requirement condition rear up high nitrogen stainless steel(HNS). However, HNS have a lot of problem such as poor workability, hot crack sensitivity. So, It is needed the condition of plastic working to overcome above many problem. In this study, VIM ingot with 100kg was made by pressurized vacuum induction melting. And then, The slab perform for hot rolling was prepared by open-die forging. Hot rolling process was performed by computer simulation according to change of height reduction, rolling temperature, heating numbers, rolling pass and so forth. The results of analysis were investigated between analysis and lab-scale rolling product.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.2
• /
• pp.161-169
• /
• 2006

Load representation has a significant impact on power system analysis and control results. In this paper, composite load models are developed based on on-line measurement data from a practical power system. Three types of static-dynamic load models are derived: general ZIP-induction motor model, Exponential-induction motor model and Z-induction motor model. For the dynamic induction motor model, two different third-order induction motor models are studied. The performances in modeling real and reactive power behaviors by composite load models are compared with other dynamic load models in terms of relative mismatch error. In addition, numerical consideration of ill-conditioned parameters is addressed based on trajectory sensitivity. Numerical studies indicate that the developed composite load models can accurately capture the dynamic behaviors of loads during disturbance.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.11
• /
• pp.9-14
• /
• 2008

This paper presents the performance analysis of 10[Gb/s] optical duobinary transmitters with the non-ideal Mach-Zehnder modulator which does not have exactly 50/50 splitting/combining ratios by computer simulations. For driving voltage ratios(=driving voltage/switching voltage) with smaller than 100[%], the transmission performance has been greatly affected by extension of LPF bandwidths. Nevertheless, the performance has been degraded when the driving voltage ratio is 100[%]. The smaller driving voltage ratios has, the more sensitivity improves by extension of LPF bandwidths under the asymmetry condition. But the driving voltage ratio with 80[%] has better bit error rate(BER) than those with 50[%] and 25[%].

• New & Renewable Energy
• /
• v.4 no.2
• /
• pp.52-60
• /
• 2008

More people have become interested in hybrid vehicles - which have been heralded as environmentally friendly automobiles - recently as the opening of domestic hybrid vehicle market draws near. Since gasoline, diesel and LPG hybrid vehicles will be produced, a need exists to conduct economic feasibility study of each vehicle type. This research analyzed projected benefits of these hybrid vehicles based on the 1600cc model. There are two categories of benefits: 1) reduced fuel costs for the owners of the vehicles; and 2) reduced environmental pollution cost. We conducted a sensitivity analysis and estimated the domestic consumer fuel costs based on the international oil prices of 100USD, 150USD, and 200USD per barrel. The analysis showed savings of 2 to 4 million Won in fuel cost and 1 to 2 million Won in environmental pollution cost; therefore, the hybrid vehicles are not economically feasible if they are between 3 to 5 million Won more expensive than the conventional internal combustion engine vehicles.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.5
• /
• pp.327-333
• /
• 2003

Several tests are performed to evaluate road booming noise. Baseline test delivers the information of road noise characteristics. Coupling effect between structure and acoustics is obtained from the mode shapes and the natural frequencies by the modal test. Equivalent stiffness at joint areas between chassis and car-body system can be determined by the input point inertance test. Noise sensitivity of body mounting point of a chassis part can be obtained from the noise transfer function test with input point inertance test. Operational deflection shape makes us analyze the actual vibration modes of the chassis system under actual leading and find noise sources very easily. Finally, the transfer path analysis is used to Identify noise Paths through the chassis system. The objectives and the procedures of the tests are described in this Paper Also, the guideline for efficient road noise evaluation test can be found.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.119-123
• /
• 2009

Recently, a MEMS gyroscope has been broadly fabricated and used due to development of a micromachining. However, there is a difference between the modeling design and the actual product and this difference can lead to the performance variation of a MEMS gyroscope. A classical design method does not exactly estimate the performance of a MEMS gyroscope. Therefore a design process considering the design variable uncertainty has to be employed to design MEMS gyroscope model. In this paper, the equation of motion of a MEMS gyroscope model is obtained to analyze the performance of a MEMS gyroscope and the effects of the design variables on the MEMS gyroscope performance are investigated. Finally the performance of MEMS gyroscope is estimated through a statistical analysis based on sample statistics.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.271-274
• /
• 2009

This paper deals with an evaluation of the product quality according to intermesh of the roller straightening process of a steel cord. To perform the experiments, a single-layered steel cord with three wires is selected as a target. Intermeshes at inlet and outlet of the roller straightening device are selected as a respective design parameter. According to two intermeshes of the roller straightening device, a design table is generated and experiments were performed. Three assessment items of the product quality, such as the residual torsion, the arc-height and the pre-forming ratio, are measured in each experimental case for the quantitative evaluation of a steel cord. Based on the measured data, the sensitivity of two intermeshes was analyzed and the prediction equation for the product quality of a steel cord was also constructed from the regression analysis.

• Food Science and Biotechnology
• /
• v.17 no.3
• /
• pp.547-552
• /
• 2008

The detection of carbamate (carbofuran, carbaryl, benfracarb, thiodicarb, and methomil) and organophosphate (diazinon, cadusafos, ethoprofos, parathion-methyl, and chlorpyrifos) pesticide residues with very low detection limits was carried out using surface plasmon resonance (SPR) based equipment. The capacity to develop a portable SPR biosensor for food safety was also investigated. The applied ligand for the immunoassays was polyclonal goat anti-rabbit immunoglobulin (IgG) peroxidase conjugate. Concentration tests using direct binding assays showed the possibility of quantitative analysis. For ligand fishing to find a proper antibody to respond to each pesticide, acetylcholinesterase (AChE), and glutathione-S-transferase (GST) were tested. The reproducibility and precision of SPR measurements were evaluated. With this approach, the limit of detection for pesticide residues was 1 ng/mL and analysis took less than 11 min. Thus, it was demonstrated that detecting multi-class pesticide residues using SPR and IgG antibodies provides enough sensitivity and speed for use in portable SPR biosensors.