• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.5
• /
• pp.350-354
• /
• 2020

In this study, a pressure sensor for each displacement was fabricated based on the silicon-based pressure sensor obtained through simulation results. Wires were bonded to the pressure sensor, and a piezoresistive pressure sensor was inserted into the printed circuit board (PCB) base by directly connecting a micro-electro-mechanical system (MEMS) sensor and a readout integrated circuit (ROIC) for signal processing. In addition, to prevent exposure, a non-conductive liquid silicone was injected into the sensor and the entire ROIC using a pipette. The packaging proceeded to block from the outside. Performing such packaging, comparing simple contact with strong contact, and confirming that the measured pulse wavelength appears accurately.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.105-109
• /
• 2015

In this study, a new airbag sensor packaging technique of directly attachment by adhesive to the automobile frame is introduced. To assess the feasibility for the packaging, a test instrument was manufactured to examine the impact sensibility by drop tests. The conventional sensor module attached mechanically by bolts with plastic housing and the new sensor packaging were installed to aluminum channel, and the results were compared with each other. Numerical analysis was also performed to investigate the signal characteristics created by the sensors. The preliminary results showed that the pattern of the MEMS sensor signal was strongly dependent on the structural behavior of the frame where the sensors were installed, which indicated the complexity of the packaging design for proper airbag deployments.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.517-518
• /
• 2008

Highly integrated ISFETs require the monolithic implementation of ISFETs, CMOS electronics, and additional sensors on the same chip This paper presents novel packaging type of CMOS ISFET pH sensor using standard CMOS FET chip and extended sensing membrane which is separated from CMOS FET. This proposed packaging type will make it easy to fabricate CMOS ISFET pH sensors

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1551_1552
• /
• 2009

In this paper, we presented the packaging technologies of CMOS ISFET(Ion Sensitive Field Effect Transistor) pH sensor using post-CMOS process and MCP(Multi Chip Packaging). We have proposed and developed two types of packaging technology. one is one chip, which sensing layer is deposited on the gate metal of standard CMOS ISFET, the other is two chip type, which sensing layer is separated from CMOS ISFET and connected by bonding wire. These proposed packaging technologies would make it easy to fabricate CMOS ISFET pH sensor and to make variety types of pH sensor.

• Journal of Sensor Science and Technology
• /
• v.25 no.3
• /
• pp.173-177
• /
• 2016

Tape casting ceramics technology has been adopted for the fabrication of solid state electrochemical $CO_2$ sensors and the packaging substrates. The fabricated $CO_2$ sensors exhibit a fast response and a good recovery with the almost theoretical sensitivity of 37 mV/decade, corresponding to a sensor operating temperature of 373 K. The two packaging methods, the wire bonding package and the surface- mounted on the ceramic package, were compared with respect to their power consumption and mass production feasibility. In terms of the ease of fabrication, the surface mount packaging technology is superior to the wire bonding technology but its power consumption is approximately twice that of the wired package.

• The monthly packaging world
• /
• s.190
• /
• pp.69-73
• /
• 2009

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2004.11a
• /
• pp.3-4
• /
• 2004

A flexible Packaging scheme, which embedded chip packaging, has been developed using a thinned silicon chip. Mechanical characteristics of thinned silicon chips are examined by bending test and finite element analysis. Thinned silicon chips ($t<50{\mu}m$) are fabricated by chemical etching process to avoid possible surface damages on them. These technologies can be use for a real-time monitoring of blood pressure. Our research targets are implantable blood pressure sensor and its telemetric measurement. By winding round the coronary arteries, we can measure the blood pressure by capacitance variation of blood vessel.

• Journal of the Korean Society of Industry Convergence
• /
• v.12 no.4
• /
• pp.215-219
• /
• 2009

A packaging technology based on flip-chip bonding and Pb-free solder for silicon pressure sensors on printed circuit board (PCB) is presented. First, the bump formation process was conducted by Pb-free solder. Ag-Sn-Cu solder and the pressed-screen printing method were used to fabricate solder bumps. The fabricated solder bumps had $189-223{\mu}m$ width, $120-160{\mu}m$ thickness, and 5.4-6.9 standard deviation. Also, shear tests was conducted to measure the bump shear strength by a Dage 2400 PC shear tester; the average shear strength was 74 g at 0.125 mm/s of test speed and $5{\mu}m$ shear height. Then, silicon pressure sensor packaging was implemented using the Pb-free solder and bump formation process. The characteristics of the pressure sensor were analogous to the results obtained when the pressure sensor dice are assembled and packaged using the standard wire-bonding technique.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.7
• /
• pp.407-412
• /
• 2017

This paper introduces a biocompatible packaging system for implantable medical device having a hermetic sealing, such that a perfect physical and chemical isolation between electronic medical system and human body (including tissue, body fluids, etc.) is obtained. The hermetic packaging includes an electronic MEMS pressure sensor, power charging system, and bluetooth communication system to wirelessly measure variation of capacitance. The packaging was acquired by Quartz direct bonding and $CO_2$ laser welding, with a size of width $ 6cm{\times}length\;10cm{\times}lheight\;3cm$. Hermetic sealing of the packaged system was tested by changing the pressure in a hermetic chamber using a precision pressure controller, from atmospheric to 900 mmHg. We found that the packaged system retained the same count or capacitance values with sensor 1 - 25,500, sensor 2 - 26,000, and sensor 3 - 20,800, at atmospheric as well as 900 mmHg pressure for 5 hours. This result shows that the packaging method has perfect hermetic sealing in any environment of the human body pressure.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.9-9
• /
• 2000

Accurate counting and packaging pills is one of the most fundamental works of the pharmaceutical industry. But it is so labor consuming and very hard to be automated. As the pharmaceutical industry is growing bigger, the need of counting and packaging automation is increasing to obtain effective mass production. Precise and quick sensing is required in the counting and processing of quickly dropping pills to improve the productivity. There are many trials for this automation and automatic machine. But the performance of the existing counting machine varies with the size, shape and the dispersion degree of pills In this research, authors design the counting and packing machine of medicinal pills that is more accurate and highly trustworthy After getting analog signal from optical sensor, pill passage is discriminated from chosen characteristic feature using microprocessor.