• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.1 s.94
• /
• pp.182-190
• /
• 1999

The objective of this study is to develop an analysis scheme in order to predict regrinding due to tool wear in shearing process. The analysis of material now and fracture in shearing process should precede the prediction of tool wear. Thus the developed FE-program to analyze shearing process is used. In order to predict tool wear, the wear model is reformulated as an incremental form and then the wear depth of tool is calculated at each deformation path. Because the regrinding of shearing tool is determined on the basis of allowable size of burr, the analysis of shearing process is iteratively performed using the worn profile of tool. To show the effectiveness of the scheme the simulation result is compared with experimental one.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.231-234
• /
• 2001

Shearing, including blanking, trimming, piercing, etc, is one of the most frequently used processes in sheet metal manufacturing. In this paper, an individual set of tooling with an in-die sensor was designed and precisely fabricated to carry out the experiment for the shearing process investigation. Through various experiments, it has been examined the influence of process parameters such as clearance, edge material properties and pad configuration. Since the tension between the part and the scrap increases when the clearance increases, the clearance should be selected properly in order to reduce the burr height. Also removal of the lower pad makes the sheared surface worse and the shearing system unstable. The shearing force increases when the clearance decreases and the friction of the tooling material decreases. Dynamic reaction force is also important to obtain the fine sheared surfaces.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.140-143
• /
• 1999

The major objective of the present paper is to develop a channel cutting machine and to establish an analytical technique for actual shearing process. Isothermal finite element(FE)-simulation of the shearing process are carried out using FE software DEFORM. The element-kill method has enabled the achievement of FE-simulation from the initial stage to the final stage of the shearing process. The effects of the punch-die clearance on the shearing process are investigated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.523-526
• /
• 1997

Sheanng is one of the most important operating processes in the field of sheet metal manufacturing. Compared with casting, forging and machining, shearing is very economical to obtain the desired shape. In recent years there has been increasing the use of shearing process in the manufacturing of small and light electronic components. In this paper, it has been researched the experimental investigation to examine the mfl uence of shearing process parameters such as clearance and lower holder configuration. Through the experiment results, the more narrow clearance gives the smaller burr height and the removal of lower holder makes the worse sheared surface. And FE simulation of shearing process using DEFORM-2D were camed out and the results compared w~th experimental studies

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.11
• /
• pp.114-123
• /
• 1996

The major objective of the present paper is to estabilish analytical technique in order to closely understand and analyze the actual shearing process. First of all, isothermal and non-isothermal FE-simulation of the shearing process are carried out using finite element software DEFORM. Based on preliminary simulation using DEFORM, the finite element program to analyze two dimensional shearing process is developed. The ductile fracture criterion and the element kill method are also used to estimate if and where a fracture will occur and to investigate the features of the sheared surface in shearing process. It can be seen that the developed program combined with the ductile fracture criterion and element kill method has enabled the achievement of FE-simulation from initial stage to final stage of shearing process. The effects of punch-die clearance on shearing process are also investigated. In order to verify the effectiveness of the proposed technique the simulation results are compared with the known expermental data. It is found that the results of the present work are in close agreement with the published experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.494-497
• /
• 2000

This paper presents the fine-shearing experimental investigation using brass sheets. Shearing including blanking, trimming, piercing, etc is one of the most frequently used processes in sheet metal manufacturing. In this study, an individual set of tooling was designed and fabricated to carry out experiment for shearing process. In order to investigate the effect of shearing surface correspond to die clearance, the profile of shearing surface was examined by using microscope. Futhermore, the relationship between shearing force and the profile of shearing surface was considered.

• Journal of Industrial Technology
• /
• v.25 no.B
• /
• pp.121-126
• /
• 2005

Micro wires manufactured by the straightening process are used in the BT(Bio-Technology), IT(Information-Technology), NT(Nano-Technology). We have developed a novel wire straightener which uses the direct heating method(DHM) for straightening the micro wire and shearing device for burr-less cutting. In this study, we confirm the tendency of micro wire after the shearing process. It is impossible to remove the burr in the shearing process. However, the embodiment of minimum burr size after the shearing process is the best in-process method. In order to minimize the burr size, we have accomplished the various experiment condition such as the U-groove, the effect of the counter punch, the shear angle, clearance.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.9
• /
• pp.62-69
• /
• 2000

Uneven clearances in the left and right sides of a press die cause deformation of the punch in precision shearing process. This deformation results from the compression stress and bending moment from shearing force in vertical direction and from the side force in horizontal direction acting to the punch, In this study the behavior of punch deformation is investigated in order to clarify the deformation state of the punch by using strain gauge deformation to shearing force side force bending moment radius of curvature and shear plane of the punch. Also we presented the calculation method of deformation size for the punch.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.1 s.94
• /
• pp.174-181
• /
• 1999

In this paper the technique to predict tool wear theoretically in shearing process is suggested. The tool wear in the process affects the tolerances of final pans, metal flows and costs of processes. In order to predict the tool wear the deformation of workpiece during the process is analyzed by using non-isothermal finite element program. The ductile fracture criterion and the element kill method are also used to estimate if and where a fracture will occur and to investigate the features of the sheared surface in shearing process. Results obtained from finite element simulation, such as nodal velocities and nodal forces, are transformed into sliding velocity and normal pressure on tool monitoring points respectively. The monitoring points are automatically generated and the wear rates on these points are accumulated during the process. It is assumed that the wear depth on the tool surface is linear function of the lot sizes based upon the known experimental results. The influence of clearance between die and punch upon tool wear is also discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.9
• /
• pp.166-171
• /
• 2002

The objective of this paper is to investigate the effect of clearance and the configuration of die system on burr formation by FEM analysis and experimental tests. Compared with casting, forging and machining, shearing has been known, especially in heavy or mass-production industries, as a very economical and fast way to obtain the desired shape Recently, the shearing process becomes widely used in the small and light electronic component manufacturing industries. When shearing a part of sheet metal, the burr formed on the cutting edge is usually unavoidable. The burr would not only degrade the precision of products but also causes additional cost for the deburring process. In this paper, the influence of shearing parameters such as clearance and configurations of the lower pad (ejector) on burr formation is investigated by using the experimental and numerical approach. From the experimental results, it has been shown that the more narrow clearance gives the smaller burr height and the higher shearing forces. The removal of lower holder also makes the sheared surface integrity and the dimensional accuracy become worse. The FEM results (using DEFORM-2D) show good agreement with the experimental results.