• 대한치과의사협회지
• /
• 제53권5호
• /
• pp.368-376
• /
• 2015

Purpose : The objective of this research was to develop a more simplified drilling procedure with an enhanced implant drill. Materials and Methods : The drill enhanced design factors enabled implantation of Dia. 5.0mm fixture with only 2 times drilling which is more simplified drilling procedure. The enhanced drill was designed with 2 flutes, 2-phase or 3-phase formed drill tip and 25 degrees of helix angle. The proposed drilling procedure (2 times) was compared with a general drilling process (4 times) in terms of temperature changes, cutting time and ISQ value. Results : The simplified drilling procedure indicated less heat than a conventional drilling procedure (p<0.05). The enhanced drill showed significantly shorter drilling time than a conventional drill (p<0.05). On the other hand, higher insertion torque and ISQ value were observed on the the suggested drilling procedure than the conventional drilling procedure (p<0.05). Conclusion : A simplified drilling procedure with the newly designed drill could provide higher effectiveness and safety of dental implant operations under properly controlled external conditions, such as irrigation and RPM of drilling.

• Journal of Periodontal and Implant Science
• /
• 제53권1호
• /
• pp.85-95
• /
• 2023

Purpose: In recent years, guided implant surgery has been widely used for the convenience of patients and surgeons. Further streamlining the surgical procedure would make implant surgery more convenient. Low-speed water-free conditions are often used in guided implant surgery. Therefore, in this study, we attempted to confirm once again whether drilling was safe at a low speed without water. The main purpose of this study was to evaluate whether a simplified drilling protocol that omits some intermediate steps in the drilling process was safe from the viewpoint of heat generation. Methods: D1 density artificial bone blocks were drilled under 50 rpm, 10 N·cm water-free conditions, and the surface temperature was measured using a digital infrared camera. First, drilling was performed with the sequential drilling method, which is the most widely used technique. Second, for each drill diameter, the temperature change was measured while performing simplified drilling with omission of the previous 1, 2, or 3 steps. Results: In sequential drilling, the heat generated during drilling at all diameters was less than the critical temperature of osteonecrosis (47℃) except for the ⌀2 drill. Statistical significance was observed in all groups when comparing sequential and simplified drilling in the ⌀3.2, ⌀3.8, and ⌀4.3 drills (P<0.001). However, in the simplified drilling procedures, the temperature was below the osteonecrosis threshold temperature (47℃) except for the ⌀4.3 drill with the omission of the previous 3 steps (⌀3.0, ⌀3.2, and ⌀3.8). Conclusions: In general, drilling under low-speed, water-free conditions has shown stable results in terms of heat generation. Simplified drilling showed statistically significantly greater heat generation than sequential drilling. However, most of the diameters and omitted steps seem to be clinically acceptable, so it will be useful if an appropriate selection is made according to the patient's clinical condition.

• 한국지진공학회논문집
• /
• 제6권4호
• /
• pp.31-37
• /
• 2002

최근에 용접 수평헌치로 보강된 내진 철골 모멘트 적합부의 응력 전달모형 및 설계법이 Lee-Uang에 의해 새로이 제안된 바가 있다. 본 연구에서는 반복재하 실물대 실험을 통하여 이 설계방안의 타당성을 실험적으로 확인하고 응력집중에서 기인하는 헌치단부의 균열을 방지할 수 있는 효과적인 상세도 제안하고자 하였다. Lee-Uang의 방안에 의해 설계된 3개의 시험체는 모두 설계의도에 부합되게, 헌치단부의 외측에서 형성된 소성힌지에서 0.04 radian에 달하는 뛰어난 소성회전능력을 발휘하였다. 도한 헌치단부에 구배를 주고 처공하거나 또는 보 웨브 스티프너를 헌치의 웨브로 부분적으로 또는 완전히 연장하는 상세에 의해 헌치단부의 균열발생을 효과적으로 방지할 수 있음을 실험적으로 입증하였다. 아울러 해석적으로 예견되었던 헌치 웨브의 스트럿 거동도 스트레인 계측을 통하여 실험적으로 입증하였다.