• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.8
• /
• pp.1377-1382
• /
• 2008

DSTATCOM(distribution static compensator) is one of the custom power devices, and protects a distribution line from unbalanced and harmonic current caused by non-linear and unbalanced loads. Researches about DSTATCOM are mainly divided two parts, one is the calculation of compensation current and the other part is the current control. Conventional researches use a LPF(low pass filter) to eliminate ripple component at the calculation of compensation current. But this method has a problem that LPF's characteristics restrict the compensation performance of instantaneous active and reactive power. This paper proposes a calculation of compensation current using state observer that can be a counterproposal of conventional methods using LPF. Improved performance of instantaneous active and reactive power compensation was shown by experiments.

• Journal of Power Electronics
• /
• v.19 no.5
• /
• pp.1315-1325
• /
• 2019

Aiming at the negative sequence and harmonic problems in the operation of railway static power conditioners, an optimization compensation strategy for negative sequence and harmonics is studied in this paper. First, the hybrid RPC topology and compensation principle are analyzed to obtain different compensation zone states and current capacities. Second, in order to optimize the RPC capacity configuration, the minimum RPC compensation capacity is calculated according to constraint conditions, and the optimal compensation coefficient and compensation angle are obtained. In addition, the voltage unbalance ${\varepsilon}_U$ and power factor requirements are satisfied. A PSO (Particle Swarm Optimization) algorithm is used to calculate the three indexes for minimum compensating energy. The proposed method can precisely calculate the optimal compensation capacity in real time. Finally, MATLAB simulations and an experimental platform verify the effectiveness and economics of the proposed algorithm.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.3
• /
• pp.289-297
• /
• 2014

This paper proposed a novel high performance sensorless control scheme for IPMSM based on an extended nonlinear state observer. The gain-matrix of the observer has been derived by using state linearization method. Steady state errors in estimated rotor position and speed due to parameter inaccuracy have been analyzed, and an equivalent flux error is defined to represent the overall effect of parameter errors contributing to the wrong convergence of the estimated rotor speed as well as rotor position. Then, an online compensation strategy was proposed to limit the estimation errors in rotor position and speed. The effectiveness of the extended nonlinear state observer is validated through simulation and experimental test.

• Smart Structures and Systems
• /
• v.14 no.6
• /
• pp.1269-1289
• /
• 2014

With the sub-stepping technique, the numerical analysis in real-time dynamic hybrid testing is split into the response analysis and signal generation tasks. Two target computers that operate in real-time may be assigned to implement these two tasks, respectively, for fully extending the simulation scale of the numerical substructure. In this case, the integration time-step of solving the dynamic response of the numerical substructure can be dozens of times bigger than the sampling time-step of the controller. The time delay between the real and desired feedback forces becomes more striking, which challenges the well-developed delay compensation methods in real-time dynamic hybrid testing. This paper focuses on displacement prediction and force correction for delay compensation in the real-time dynamic hybrid testing with a large integration time-step. A new displacement prediction scheme is proposed based on recently-developed explicit integration algorithms and compared with several commonly-used prediction procedures. The evaluation of its prediction accuracy is carried out theoretically, numerically and experimentally. Results indicate that the accuracy and effectiveness of the proposed prediction method are of significance.

• Journal of Biomedical Engineering Research
• /
• v.18 no.4
• /
• pp.477-484
• /
• 1997

In this paper, we proposed the compensation method to evaluate arousal level in different initial arousal states. Arousal level was measured by the relationship between IRI and Nz. Since Nz is affected by BI which is directly proportional to initial arousal state of subjects, the arousal level is underestimated To overcome this problem, we proposed the compensation method using modified Karolinska sleepiness scale, and determined compensation coefficients derived from this scale with five arousal levels. Applying these coefficients to portable arousal monitoring system, the proposed method in this paper could be useful for real-time evaluation and control of arousal level. As a result the developed system can detect and control the arousal state from initial drowsing sate.

• Fire Science and Engineering
• /
• v.33 no.5
• /
• pp.109-117
• /
• 2019

When those who have caused a fire have no ability to compensate fire victims, the victims tend to charge fire agencies for state compensation to receive damage relief. This study analyzed two state compensation cases related to fires. The findings suggest that if there is a causal relationship between fire damage and mistakes committed by fire officials that are associated with fire prevention or special fire inspections, courts usually decide that fire agencies should compensate fire victims. Despite the introduction of a new article in the Framework Act on Fire-Fighting Services on December 26, 2017, titled "Exemption from Responsibility for Fire-Fighting Activities", exemptions are only available if inevitability of the activity has been proven. However, unlike rescue or first aid activity, inevitability is difficult to prove when it comes to fire inspection activity. Therefore, it is expected that state compensation suits related to fires will not decrease.

• Journal of Digital Convergence
• /
• v.14 no.6
• /
• pp.51-60
• /
• 2016

The modern state has always followed a variety of risks in the industrialization and informatization trends in the development of science and technology. Under such an environment, A matter of State compensation should take into consideration a variety of values such as harmony relief victims' rights in accordance with the principles of the rule of law, suppression of illegal acts of public servants, ensuring stable performance of official duties, the national treasury stability. As the state takes responsibility for an act of a public servant in a modern constitutional state, there may be a doubt on that the state takes responsibility only when there is a deliberation or a mistake. According to the theory of the self-responsibility, which suits the Constitution, the principle of liability with mistake on the State Compensation Law shall be excluded. I agree to the opinion that a subjective responsibility prerequisite such as a deliberation or a mistake is not required in relation to the liability of reparation on the State Compensation Law. Therefore, it is needed to convert the principle of state liability of reparation from the principle of liability with mistake to the principle of liability without mistake through a fundamental revision of the State Compensation Law.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.1
• /
• pp.121-127
• /
• 2012

An electric power compensation system for a DC transmission system with an integrated wind turbine generator is proposed. The proposed compensation system consists of a synchronous generator and a duplex reactor. This apparatus is connected to the sending-end circuit of the DC transmission system. A set of steady-state equations of the system is first derived. Then, the effect of the duplex reactor, which can eliminate the sending-end grid current distortion due to commutation of the converter, is explored. The relationships among power at the sending-end circuit are also revealed. It is shown that fluctuations in the sending-end grid power due to changes in wind velocities are compensated with the proposed system. Finally, the effects of the sending-end grid conditions on the steady-state characteristics of the system are studied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.390-391
• /
• 2007

We have studied improvement of light leakage of twisted nematic liquid crystal display (TN-LCD) in dark state using the hybrid aligned compensation film made of rod-like LC. When the voltage is applied properly to the TN-LCD, the director tilts up but LC director on the substrate don't tilts up due to surface anchoring energy of the LC cell. Accordingly, LC director from surface to middle LC of TN -LCD become hybrid state such as hybrid aligned film. Consequently, in this paper we achieve wide viewing angle performances of TN mode using developed hybrid aligned film which especially decreases light leakage at vertical direction in dark state.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.30-40
• /
• 2015

For a shunt power quality controller (SPQC) the DC side voltage value which is closely related to the compensation performance is a significant parameter. Buy so far, very little discussion has been conducted on this in a quantitative manner by previous publications. In this paper, a method to design the DC side voltage of SPQC is presented according to the compensation performance in the single-phase system and the three-phase system respectively. First, for the reactive current and the harmonic current compensation, a required minimal value of the DC side voltage with a zero total harmonic distortion (THD) of the source current and a unit power factor is obtained for a typical load, through the equivalent circuit analysis and the Fourier Transform analytical expressions. Second, when the DC side voltage of SPQC is lower than the above-obtained minimal value, the quantitative relationship between the DC side voltage and the THD after compensation is also elaborated using the curve diagram. Hardware experimental results verify the design method.