• Journal of Biosystems Engineering
• /
• v.18 no.4
• /
• pp.382-389
• /
• 1993

In this research, the surface color of 'Fuji' apples and tomatoes were measured by using Sharp PD 151 semiconductor color sensors. The measurements were compared with color-difference-meter readings and with visual sensory test scores. A negative exponential function was developed which describe the relationship between the dominant wavelength of the surface color of 'Fuji' apples and the ratio of the photoelectric currents of the color sensor. Also a linear relationship was found for the surface color of tomatoes and the color sensor output. There were good correlations between the visual test scores and the color sensor output for both 'Fuji' apples and tomatoes.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.22 no.1
• /
• pp.7-15
• /
• 2016

Purpose: There are the number of color tactile walking surface indicators installed in Korea, because of indefinite regulation in blind and vision-impaired persons' tactile walking surface indicators. In case of yellow tactile walking surface indicators, it shows a deviation severe color. In this study, the researchers suggested color and brightness reference for helping blind and vision-impaired persons' walking through analyzing the color references of tactile walking surface indicators and the color luminance between tactile walking surface indicators and sidewalk currently used. Method: Reasonable luminance contrast criteria is suggested by examining ways of improving the recognition and recognition of objects according to color contrast visually impaired through literature review and analyzing standards of tactile walking surface indicators and the Europe, Japan and Australia of color and luminance contrast criteria. And by examining the color of the tactile walking surface indicators reported in Korea currently used to derive the problem presented by the luminance contrast in the reference and comparison. Finally, the visually impaired tactile walking surface indicators is set for color selection criteria for the recognition rate improves. Results: In order to improve the recognition rate to be tactile walking surface indicators of the contrast of the visually impaired and the environment than the color of the tactile walking surface indicators itself to secure always a certain level or more of brightness contrast values in the set of the color of the tactile walking surface indicators so important. Implication: In order to set the blind tactile walking surface indicators color recognition based on the verification of the real pedestrian based on the results presented in this paper it is required. It is to be understood as an element of the barrier free configuration for securing the walking pedestrian safety.

• Journal of the Optical Society of Korea
• /
• v.19 no.6
• /
• pp.649-657
• /
• 2015

We present a surface color measurement including quantities of surface color, methods, and uncertainty evaluation. Based on a relation between spectral reflectance and surface color, we study how an uncertainty of spectral reflectance propagates to surface color. In analyzing the uncertainty propagation, we divide the uncertainty into uncorrelated components, fully correlated components, and correlated components with spectrally varying correlations. As an experimental example, we perform spectro-reflectometric measurements for ceramic color plates. With measured spectral reflectance and its uncertainty evaluation, we determine surface color and analyze uncertainties of the ceramic color plates.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.4
• /
• pp.309-316
• /
• 2014

PURPOSE. The color of the ceramic restorations is affected by various factors such as brand, thickness of the layered the ceramic, condensation techniques, smoothness of surface, number of firings, firing temperature and thickness of dentin. The aim of this study was to evaluate the color change and surface roughness in dental porcelain with different thicknesses during repeated firings. MATERIALS AND METHODS. Disc-shaped (N=21) metal-ceramic samples (IPS Classic; Ivoclar Vivadent; Shaar, Liechtenstein) with different thickness were exposed to repeated firings. Color measurement of the samples was made using a colorimeter and profilometer was used to determine surface roughness. ANOVA and Tukey tests with repeated measurements were used for statistical analysis. RESULTS. The total thickness of the ceramics which is less than 2 mm significantly have detrimental effect on the surface properties and color of porcelains during firings (P<.05). CONCLUSION. Repeated firings have effects on the color change and surface roughness of the dental ceramics and should be avoided.

• Journal of the Korea Furniture Society
• /
• v.26 no.3
• /
• pp.262-266
• /
• 2015

This study was carried out to analyze the surface color change according to the weathering time. The surface color of material was one of evaluation indexes in exposure experiment. For the purpose, accelerated weathering test was performed with wood. The weathering time level was composed with 0, 500, 1000, 1500 and 2000 hours and color difference was estimated with the color difference meter. The surface color was changed to 500 hours that lightness and redness were decreased and yellowness was increased. However it did not changed after 500 hours. It means that the surface color could be the evaluation index of deterioration of the wood but it means very little after certain time.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.18 no.3 s.39
• /
• pp.115-135
• /
• 1990

The purpose of this study was to suggest an improvement proposal for colors in urban environment with special regard to the surface color and their situations of apartment buildings in Seoul. For this goal, 167 cases of different color types of apartment buildings were surveyed. And, the survey was performed in the view of color by areas, by localtion, by builder, by paint year, by built year, by appearance of building, and by surface texture to prove the influencing factors on the surface colors. These collected data analyzed and compared with the existing studies to find out the changing trend of colors. The results are as follows : 1) The use of neutral gray($26.4{\%}$) and warm color(YR, Y, GY; 56.4%) were dominant and the usage trend of higher 'value'(87.4%) and lower 'saturation'(73.0%) was obvious. Especially, the use of PB and P was noticeable. 2) In comparing the existing studies, the changing trend in the surface color pattern was found. That is, neutral gray was used dominantly in 1970's, warm color(YR, Y)in the middle of 1980's. In the end of 1980's, warm color were also used dominantly same as before and GY, PB, P were used noticeably with some rising tendency of higher 'value' and lower 'saturation' was obvious. 3) The results of analysis by localtion shows that the different color groups might exist in Seoul city. Neutral gray and YR were dominant in zone I. Warm colors(YR, Y, GY)were prevailed in zone II, III, IV. In zone V, many colors were evenly used. In zone VI, middle values at warm color were dominant. Progressively, these color groups with further study could be considered in the color management in urban environment possibly. 4) Surface color of apartment buildings were different from their builders. 5) Concerned with the painted year, the use of higher 'value' and lower 'saturation' was increased gradually with the change of times. 6) the analysis by the built year revealed that the 'value' of surface colors on the old buildings was lower than that of the new ones. 7) The 'value' of colors on the surface with texture was higher than that of the surface without texture. 8) In the combination of two colors, the use of 'value' with difference at the same 'hue' was found harmonions in many cases, but the 'saturation' in usage was included in the ambiguity (Moon & Spencer's term). The ambiguity in color harmony should be improved in the near future.

• Journal of Biosystems Engineering
• /
• v.37 no.4
• /
• pp.252-257
• /
• 2012

Purpose: The net rind pattern and color of melon surface are important for a high market value of melon fruits. The development of the net and color are closely related to the changes in shape, size, and maturing. Therefore, the net and color characteristics can be used indicators for assessment of melon quality. The goal of this study was to investigate the possibility of estimating melon soluble solids content (SSC) and firmness by analyzing the net and color characteristics of fruit surface. Methods: The true color images of melon surface obtained at fruit equator were analyzed with 18 color features and 9 texture features. The partial least squares (PLS) method was used to estimate SSC and firmness in melons using their color and texture features. Results: In sensing melon SSC, the coefficients of determination of validation (${R_v}^2$) of the prediction models using the color and texture features were 0.84 (root mean square error of validation, RMSEV: 1.92 $^{\circ}Brix$) and 0.96 (RMSEV: 0.60 $^{\circ}Brix$), respectively. The ${R_v}^2$ values of the models for predicting melon firmness using the color and texture features were 0.64 (RMSEV: 4.62 N) and 0.79 (RMSEV: 2.99 N), respectively. Conclusions: In general, the texture features were more useful for estimating melon internal quality than the color features. However, to strengthen the usefulness of the color and texture features of melon surface for estimation of melon quality, additional experiments with more fruit samples need to be conducted.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.16 no.3
• /
• pp.121-131
• /
• 1998

The object color does not look same under the different light source. It depends on the surface spectral reflectance and the spectral distribution of light source. Therefore we should find the surface spectral reflectance of object color and the spectral distribution of light source for color reproduction. Using Wiener estimation, we can estimate the spectral reflectance from low dimensional images obtained with multi-band image acquisition system. The kind and the number of imaging filters have the effect on the estimation of the spectral reflectance. Therefore it is important that optimal filters are selected to minimize the error of the result. In this paper, we describe methods to select optimal filters with minimum error between measured and estimated surface spectral reflectance and to estimate surface spectral reflectance of Munsell color chart from six multi-band images by using Wiener estimation.

• Proceedings of the Korean Printing Society Conference
• /
• 1998.10a
• /
• pp.1-6
• /
• 1998

The object color does not look same under the different light source. It depends on the surface spectral reflectance and the spectral distribution of light source. Therefore we should find the surface spectral reflectance of object color and the spectral distribution of light source for color reproduction. Using Winer estimation, we can reconstruct the spectral reflectance from low dimensional images obtained with a few filters. The kind and the number of filters have the effect on the estimation of the spectral reflectance. Therefore it is important that optimal filters are selected to minimize the error of the result. In this paper, we describe methods to select optimal filters with minimum error between measured and estimated surface spectral reflectance and to estimate surface spectral reflectance of Munsell color from six band images by using Wiener estimation.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.2
• /
• pp.325-336
• /
• 2002

This study investigated color change of combination dyeing silk fabrics dyed with Turmeric extracts and Gardenia extracts after dyeing of Indian indigo. Experimental variables include the condition of dyeing time and concentration of Turmeric extracts, Gardenia extracts, arid dyeing cycle of Indian indigo. Surface color of silk fabrics dyed with Turmeric 77tracts after one cycle dyeing, two cycles dyeing, four cycles dyeing of Indian indigo was changed from 5.1GY to 0.3GY, 1.5G to 3.5GY and 6.5G to 5.8GY by increase of concentration of Turmeric extracts. On the other hand, Surface color of silk fabrics dyed with Gardenia extracts after one cycle dyeing, two cycles dyeing, four cycles dyeing of Indian indigo was changed from 7.5Y to 3.9Y, 1.2GY to 6.7Y and 4.0GY to 8.6GY by increase of concentration of Gardenia extracts. Its range of surface color was changed to green and yellowish green by increase of dyeing time with concentration of Turmeric extracts. On the other hand, its range of surface color was changed to yellowish and yellow by increase of dyeing time with concentration of Gardenia extracts.