• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.6
• /
• pp.730-740
• /
• 1999

The purpose of this study was to investigate setting and thermal expansion of dental soldering investments. In order to compare expansion rates and to investigate the effect of water/powder ratio on expansion, setting and thermal expansion of low dental soldering investments were measured under three different water/powder ratio conditions. standard, 20% decreased and 20% increased. Setting expansion of investments was measured by use of dialgauge method. Each measurement was started two minutes later from the beginning of spatulation and recorded every one minute for one hour. Thermal expansion of cylindrical test specimens, 10mm diameter, 50mm length, was recorded in a thermodilatometer at heating rate of $10^{\circ}C$ per minute from $25^{\circ}C\;to\;700^{\circ}C$. The results of this study were obtained as follows: 1. Setting expansion rates under the standard water/powder ratio condition were 0.198% in Speed-E, 0.090% in Deguvest, 0.080% in CM and Hi-temp. Setting expansion of Speed-E was significantly different from those of CM, Deguvest and Hi-temp, and setting expansion of Deguvest was significantly different from those of CM and Hi-temp(p<.05). 2. Under the decreased water/powder ratio condition, there was significant increase in setting expansion of 4 dental soldering investments (p<.05). 3. There were no significant differences in setting expansions of investments except Hi-temp between standard and increased water/powder ratio condition(p<.05). 4. Thermal expansion rates under the standard water/powder ratio condition were 1.923% in Deguvest, 1.629% in Speed-E, 1.619% in Hi-temp and 1.580% in CM. No significant differences in thermal expansions under the standard water/powder ratio condition existed only between Speed-I and Hi-temp(p<.05) 5. Under the decreased water/powder ratio condition, there was significant increase in thermal expansion of CM and Deguvest but decrease in thermal expansion of Speed-E (p<.05). 6. Under the increased water/powder ratio condition, there was significant decrease in thermal expansion of CM, Deguvest and Speed-I but decrease in thermal expansion of Hi-temp(p<.05).

• Structural Engineering and Mechanics
• /
• v.60 no.2
• /
• pp.313-335
• /
• 2016

In this article, a four-variable refined plate theory is presented for buckling analysis of functionally graded plates subjected to uniform, linear and non-linear temperature rises across the thickness direction. The theory accounts for parabolic distribution of the transverse shear strains, and satisfies the zero traction boundary conditions on the surfaces of the plate without using shear correction factor. Young's modulus and Poisson ratio of the FGM plates are assumed to remain constant throughout the entire plate. However, the coefficient of thermal expansion of the FGM plate varies according to a power law form through the thickness coordinate. Equilibrium and stability equations are derived based on the present theory. The influences of many plate parameters on buckling temperature difference such ratio of thermal expansion, aspect ratio, side-to-thickness ratio and gradient index will be investigated.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.355-356
• /
• 2009

The change of thermal expansion and mechanical behaviors by cold working has been investigated in Fe-29%Ni-17%Co low thermal expansion Kovar alloy. Fe-29%Ni-17%Co alloy was cold rolled gradually and prepared to plates having reduction ratio of 0%, 20%, 40%, 60%, and 80%. Annealing effect on the properties was also studied. Thermal expansion was measured from $25^{\circ}C$ to $600^{\circ}C$ with a heating rate of $5^{\circ}C$/min by using vacuum differential dilatometer. It was found that thermal expansion coefficient ($\alpha_{30{\sim}400}$) slightly decreased (reduction ration of 20%) and then remarkably increased (above reduction ration of 40%) with increasing reduction ratio of cold rolling. Thermal expansion coefficient ($\alpha_{30{\sim}400}$) was sharply decreased after annealing heat-treatment. Yield and tensile strengths were continuously increased and elongation was decreased by cold roiling. Microstructural observation and X-ray diffraction analysis results showed that the $\alpha$ phase significantly increased as the reduction ratio increased. The slight decrease of thermal expansion coefficient bellow reduction ration of 20% could be explained by the destroying short-range ordering and the decreasing of grain size. The significant increase of thermal expansion coefficient with cold rolling mainly attributed to the appearance of $\alpha$ phase. The correlation between the microstructural cause and invar phenomena for the low thermal expansion behavior was also discussed.

• Restorative Dentistry and Endodontics
• /
• v.5 no.1
• /
• pp.29-34
• /
• 1979

The purpose of this study was to measure thermal expansions of dental investments, Biovest(Casting Investment. Dentsply International INC, U.S.A.), Multi-Best (Use for all dental chrome-cobalt alloys, The Ransom & Randolph Co. U.S.A.), Kerr(Inlay Investment. Sybron Kerr, U.S.A.), O. K. (Inlay Investment. Shofu Dental MFG, Co. Japan), Whip-Mix (Cristobalite Inlay Investment. Whip-Mix Corporation. U.S.A.). Thermal expansion of specimens(5mm in diameter and 50mm in length) was measured by a dilatometer at the temperature range from $20^{\circ}C$ to $700^{\circ}C$ by comparing expansion between standardized quartz and experimental specimens with heating rate about $300^{\circ}C$/hr. The following results were obtained. 1. The coefficient of thermal expansion of Biovest was $15{\times}10^{-6}/^{\circ}C$ in the water powder ratio 18/100 and $14{\times}10^{-6}/^{\circ}C$ in the water powder ratio 28/100. Those of Multi-Best were $9{\times}10^{-6}/^{\circ}C$ in the water powder ratio 14/100 and $7{\times}10^{-6}/^{\circ}C$ in the water powder ratio 24/100. 2. The coefficient of thermal expansion of Kerr were $17{\times}10^{-6}/^{\circ}C$ in the water powder ratio 38/100 and $14{\times}10^{-6}/^{\circ}c$ in the water powder ratio 48/100. Those of O. K. were $9{\times}10^{-6}/^{\circ}C$ in the water powder ratio 33/100 and $7{\times}10^{-6}/^{\circ}C$ in the water powder ratio 43/100 3. The coefficient of thermal expansion of Whip-Mix were $14{\times}10^{-6}/^{\circ}C$ in the water powder ritio 40/100 and $12{\times}10^{-6}/^{\circ}c$ Fein the water powder ratio 50/100. Those of Hi-Heat were $11{\times}10^{-6}/^{\circ}c$ in the water powder ratio 28/100 and $10{\times}10^{-6}/^{\circ}c$ in the water powder ratio 38/100.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.95-98
• /
• 2005

This paper proposes the solutions predicting the coefficient of the thermal expansion changes of composites which include the fiber-like shaped ($a_1$ > ($a_2$ = ($a_3$) and the disk-like shaped (al = a2> a3) inclusions like two dimensional geometries, which has one aspect ratios, ${\alpha}$ = ($a_1$ /($a_3$). The analysis follows the procedure developed for elastic moduli by using the generalized approach of Eshelby’s equivalent tensor. The influences of the aspect ratios, on the effective coefficient of thermal expansion of composites containing aligned isotropic inclusions are examined. This model should be limited to analyze the composites with unidirectionally aligned inclusions and with complete binding to each other of both matrix and inclusions having homogeneous properties. The coefficient of thermal expansion of composites (${\theta}_{11}$,${\theta}_{22}$and ${\theta}_{33}$) are investigated. From material data of the composites with glass fiber in epoxy resin, the thermal expansions along the aspect ratio were obtained and similar to the Chow model. The longitudinal coefficients of thermal expansion ${\theta}_{11}$decrease, as the aspect ratios increase. However, the transverse coefficients of thermal expansion ${\theta}_{22}$increase or decrease, as the aspect ratios increase. And both of them decrease, as the concentration increases.

• The Journal of Korean Academy of Prosthodontics
• /
• v.28 no.1
• /
• pp.137-163
• /
• 1990

The properties of a investment material can be described by the consistency at the slurry state, the setting time, the compressive strength and the thermal expansion during the casting. In this study the effect of the production parameters which are included the ratio of quartz and cristobalite, the content of binder, the water powder ratio and the content and concentration of additives on the Properties of the gypsum-bonded investments has been investigated with help of the consistency test, the vicat needle test, the compressive strength test, the thermal expansion test, x-ray diffraction and DTA thermal differential test. The experimental results showed that the constitution of a investment with W/P ratio of 0.34, 30% of gypsum, 0.8% aluminium sulfate, 2% magnesium sulfate, 0.6% sodium phosphate was adapted for the properties of the KDA Spec. No. 13 type I investment. The important experimental results are summarized as follows. 1. The consistency of the investment decreased with increasing amount of aluminium sulfate and decreasing amount of sodium phosphate. An addition of magnesium sulfate up to 2% an increase of the consistency was shown. But 3% magnesium sulfate in investment showed a decrease of the consistency. The consistency did not vary significantly with a variation of the content of gypsum and cristobalite and the W/P ratio. 2. Aluminium sulfate and the magnesium sulfate promoted the hardening and the aluminium phosphate delayed the hardening. The setting time increased with amount of gypsum. The effect of the matrix on the setting time was insignificant. With the W/P ratio of 0.34 the setting time was 14 min. 3. The compressive strength decreased with the amount of aluminium sulfate up to 0.25% and increased with the amount of aluminium sulfate greater than 3%. The compressive strength decreased as decreasing the amount of magnesium sulfate and gypsum and as increasing the W/P ratio. The effect of the refractory on the compressive strength was also not significant. With the W/P ratio of 0.34 the compressive strength was $34Kg/mm^2$. 4. The 1st thermal expansion was found at the temperature near and the steady state or the contraction stage was found at the temperature between $250^{\circ}C$ and $500^{\circ}C$. After this stage the 2nd thermal expansion took place at the temperature near $500^{\circ}C$. The amount of thermal expansion increased with decreasing the content of magnesium sulfate, aluminium sulfate and gypsum and the W/P ratio. And the amount of thermal expansion increased as the content of sodium phosphate and cristobalite. With the W/P ratio of 0.34 the amount of total expansion was 1.2%.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.1
• /
• pp.139-165
• /
• 1991

The properties of a investment material can be described by the consistency at the slurry state, the setting time, the compressive strength and the thermal expansion during the casting. In this study the effect of the production parameters which are included the ratio of quartz and cristobalite, the content of binder, the water powder ratio and the content and concentration of additives on the properties of the gypsum-bonded investments has been investigated with help of the consistency test, the vicat needle test, the compressive strength test, the thermal expansion test, x-ray diffraction and DTA thermal differential test. The experimental results showed that the constitution of a investment with W/P ratio of 0.34, 30% of gypsum, 0.8% aluminium sulfate, 2% magnesium sulfate, 0.6% sodium phosphate was adapted for the properties of the KDA Spec. No. 13 type I investment. The important experimental results are summarized as follows. 1. The consistency of the investment decreased with increasing amount of aluminium sulfate and decreasing amount of sodium phosphate. An addition of magnesium sulfate up to 2% an increase of the consistency was shown. But 3% magnesium sulfate in investment showed a decrease of consistency. The consistency did not vary significantly with a variation of the content of gypsum and cristobalite and the W/P ratio. 2. Aluminium sulfata and the magnesium sulfate promoted the hardening and the aluminium phoshpate delayed the hardening. The setting time increased with amount of gypsum. The effect of the matrix on the setting time was insignificant. With the W/P ratio of 0.34 the setting time was 14 min. 3. The compressive strength decreased with the amount of aluminium sulfate up to 0.25% and increased with the amount of aluminium sulfate greater than 3%. The compressive strength decreased as decreasing the amount of magnesium sulfate and gypsum and as increasing the W/P ratio. The effect fo the refractory on the compressive strength was also not significant. With the W/P ratio of 0.34 the compressive strength was $34Kg/mm^2$. 4. The 1st thermal expansion was found at the temperature near $250^{\circ}C$ and the steady state or the contraction stage was found at the temperature between $250^{\circ}C$ and $500^{\circ}C$. After this stage the 2nd thermal expansion took place at the temperature near $500^{\circ}C$. The amount of thermal expansion increased with decreasing the content of magnesium sulfate, aluminium sulfate and gypsum and the W/P ratio. And the amount of thermal expansion increased as the content of sodium phosphate ad cristobalite. With the W/P ratio of 0.34 the amount of total expansion was 1.2%.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.6
• /
• pp.835-842
• /
• 2009

The present thesis carried out a research on a compression pressure's reduction phenomenon and its countermeasure according to the thermal efficiency improvement method by a Miller method in 4-cycle low speed diesel engine. In case of retardation of intake valve closing time in a engine, the theoretical heat efficiency shows a remarkably reducing trend when a compression ratio is not compensated. Accordingly, the thermal efficiency showed an increasing trend in case of compensating the compression ratio. Especially, it could be understood that the theoretical heat efficiency at near ABDC $100^{\circ}$ of intake valve closing time in case of compensation of the compression ratio was improved by around 25.1%, and the mean effective pressure was also increased by around 18.6%. Also, as the retardation of intake valve closing time increases, air quantity becomes insufficient due to a backflow phenomenon of intake air and thus thermal efficiency was decreased in a high load operation domain. The solving method of this problem is possible by supercharge. Therefore, in order to improve thermal efficiency by retardation of ntake valve closing time, the thermal efficiency improvement according to low compression is possible when there are a compensation device of a compression ratio and a supercharge device. This is a problem-solving method of low compression and high expansion cycle.

• The Journal of Engineering Research
• /
• v.6 no.2
• /
• pp.141-151
• /
• 2004

The physical properties of gold investment materials are depending on it's thermal expansion coefficients, compressive strength, and particles size distributions. Normally the gold investment materials are consisted of cristobalite, quartz and plaster. Since the thermal expansion coefficient of cristobalite and quartz are $2.6\times10^{-6}/^\circC$, $2.32\times10^{-6}/^\circC$, respectively, the composition ratio of each components influence the thermal and clinical properties of gold investment materials. Recently are imported from overseas and the commercial market is expected to expand. Thus it is necessary to develop the optimum strength and compressive strength of gold investment materials which the an homogeneous size distribution and thermal expansion coefficients. Therefore two different experiments has been done. Firstly the homogeneous cristobalite and quartz are made by pulverizing milling. Secondly the compressive strength and thermal expansion coefficients are analysed by the composition ratio of cristobalite and quartz. As a results of experiments, homogeneous distribution of cristobalite and quartz are observed by pulverizing and milling. The optimum compressive strength was obtained at the ratio of 45:25 cristobalite, quartz respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1141-1148
• /
• 2008

One of the methods to increase the efficiency of an engine is to expand pressures obtained from combustions equal to the pressure of atmosphere as much as possible and then convert thermal energy into mechanical energy also as much as possible. In this research, the Diesel cycle was thermodynamically interpreted to evaluate the possibility of high efficiency by converting Diesel engines to the Atkinson cycle, and general cycle features were analyzed after comparing these two cycles. In the case of fuel air the Diesel-Atkinson cycle considering intake and exhaust similar to real cycles, the value of thermal efficiency and average effective pressure increased, though their values were smaller than those of standard air amount cycle, when expansion compression ratio increased. When normal Diesel engines of which compression stroke and expansion stroke are all the same, was converted to the Atkinson cycle by changing the time of intake value close, combustion pressure reduced due to reduced expansion compression ratio and intake air amount due to decreased effective cycle volume.