• Journal of ILASS-Korea
• /
• v.12 no.2
• /
• pp.79-85
• /
• 2007

In this study, the effect of jet velocity profile on the thickness and velocity of the liquid sheet formed by two impinging low speed jets was investigated. To predict the distribution of thickness and velocity of liquid sheet theoretically, the jet velocity profile which was measured experimentally was adopted in addition to the constant jet velocity as well as Poiseuille's parabolic profile. For three cases, the distribution of thickness and velocity of liquid sheet was analytically predicted by solving conservation equations including stagnation point. The predicted results were compared with previous experimental results. The jet velocity profile definitely affected the resulting characteristics of liquid sheet. The distribution of thickness and velocity of liquid sheet was more close to the measured results compared with that which was predicted by the assumption of constant jet velocity.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.384-387
• /
• 2006

Vertical L/UL (Load/Unload) velocity is very important parameter to determine the L/UL performance, and the vertical velocity is determined by the actuator velocity and the ramp profile. However, it is not easy to precisely control the actuator rotating velocity during the L/UL process. Especially in emergency parking, servo system doesn't operate, it is impossible to control an actuator velocity. Then, the vertical unloading velocity depends on only ramp profile. The ramp height and the sliding length for L/UL process in SFF (Small Form Factor) HDD are restricted due to slimness and small media. For these reasons, it is very difficult to design the ramp profile in SFF HDD. Therefore, this study analyzes the unloading dynamic characteristics for various ramp profiles and makes the thesis for ramp profile design.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.2
• /
• pp.150-155
• /
• 2006

Vertical L/UL (Load/Unload) velocity is very important parameter to determine the L/UL performance, and the vertical velocity is determined by the actuator velocity and the ramp profile. However, it is not easy to precisely control the actuator rotating velocity during the L/UL process. Especially in emergency parking, servo system doesn't operate, it is impossible to control an actuator velocity. Then, the vertical unloading velocity depends on only ramp profile. The ramp height and the sliding length for L/UL process in SFF (Small Form Factor) HDD are restricted due to slimness and small media. For these reasons, it is very difficult to design the ramp profile in SFF HDD. Therefore, this study analyzes the unloading dynamic characteristics for various ramp profiles and makes the thesis for ramp profile design.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.12
• /
• pp.1079-1085
• /
• 2012

For precise motion control, S-curve velocity profile is generally used but it has disadvantage of relatively long calculation time for floating-point arithmetics. In this paper, we present a new generating method for velocity profile to reduce delay time of profile generation so that it overcomes such disadvantage and enhances the efficiency of precise motion control. In this approach, the velocity profile is designed based on the gamma correction expression that is generally used in image processing to obtain a smoother movement without any critical jerk. The proposed velocity profile is designed to support both T-curve and S-curve velocity profile. It can generate precise profile by adding an offset to the velocity profile with decimals under floating point that are not counted during gamma correction arithmetic operation. As a result, the operation time is saved and the efficiency is improved. The proposed method is compared with the existing method that generates velocity profile using ring buffer on a 8-bit low-cost MCU. The result shows that the proposed method has no delay in generating driving profile with good accuracy of each cycle velocity. The significance of the proposed method lies in reduction of the operation time without degrading the motion accuracy. Generated driving signal also shows to verify effectiveness of the proposed method.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1749-1754
• /
• 2004

In order to measure non-intrusively velocity profile in liquid metal flow, a modified electromagnetic flowmeter was designed, which was based on electromagnetic tomography technique. Under the assumption that flow is fully-developed, axisymmetric and rectilinear, the velocity profile was reconstructed after the flowmeter equation, the first kind of Fredholm integration equation, was linearized. In reconstruction process Tikhonov regularization method with regularization parameter was used. The reconstructed velocity profile had the nearly same as turbulent flow profile which was approximately represented as log law. In addition, flowmeter output for a fixed magnet rotation angle was linearly proportional to flow rate. When magnet rotation angle was $54^{\circ}$, axisymmetric weight function was nearly uniform so that the flowmeter gives a constant signal for any fully-developed, axisymmetric and rectilinear profile with a constant flow rate.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.2
• /
• pp.29-36
• /
• 2019

There always exist the spatial variations of material properties such as a shear wave velocity in a dam and between same type dams. These uncertainties cause those in evaluation of a shear wave velocity profile of a dam and should be considered in determining the shear wave velocity profile for a rockfill zone of a fill dam. In this paper, these uncertainties of a shear wave velocity in the rockfill zone of the fill dam in Korea are evaluated. And the shear wave velocity profile model considering these uncertainties in rockfillzone is proposed using the method based on Harmonic wavelet transform. The proposed shear wave velocity profile model is compared with Sawada-Takahashi model widely used for evaluation of a shear wave velocity profile of a rockfill zone of fill dams.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.10
• /
• pp.1271-1278
• /
• 2004

In order to measure non-intrusively velocity profile in liquid metal flow, a modified electromagnetic flowmeter was designed, which was based on electromagnetic tomography technique. Under the assumption that flow is fully-developed, axisymmetric and rectilinear, the velocity profile was reconstructed after the flowmeter equation, the first kind of Fredholm integration equation, was linearized. In reconstruction process Tikhonov regularization method with regularization parameter was used. The reconstructed velocity profile had the nearly same as turbulent flow profile which was approximately represented as log law. In addition, flowmeter output fur a fixed magnet rotation angle was linearly proportional to flow rate. When magnet rotation angle was 54$^{\circ}$, axisymmetric weight function was nearly uniform so that the flowmeter gives a constant signal for any fully-developed, axisymmetric and rectilinear profile with a constant flow rate.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.1157-1159
• /
• 2003

The effect of the scan velocity modulation is studied. The effect of the velocity modulation on the picture image is judged from the intensity profile of the image. The intensity profile is obtained as time integral of moving Gaussian beam. To confirm the applicability of this integral formula, the measurement and simulation data is compared. And by calculating the intensity profile for different amounts of velocity modulation, the optimum modulation displacement that gives the best image quality is obtained. This optimum modulation displacement can be used in designing scan velocity modulation system.

• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.221-228
• /
• 2000

In this paper, analytical study is performed to reduce residual vibration in seeking mode of optical pick-up. The conditions for acceleration adn deceleration time in trapezoidal velocity profile to reduce residual vibration are derived for undamped vibration system. To verify the validity of conditiosn two example studies are carried out. Numerical and experimental implementations for flexible arm system attached to moving part show that residual vibration is effectively reduced by calculated velocity profile. In addition, simulation study for optical pick-up reveals that by changing natural frequency to resonance frequency the conditions derived assuming undamped system can be applied to obtain velocity profile for minimum residual energy in damped vibration system.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.986-990
• /
• 2005

The present study aims to illuminate the vertical velocity profile of outer region of open-channel flow. Two sets of experiments were performed with PIV and propeller velocimeter. The first set was conducted to investigate the effect of bed roughness on the velocity distribution. The second set of experiments was carried out to find the effect of the Froude number on the velocity profile under the same bed roughness. The results reveal that the wake-law fits well with the experimental data from the bottom to the depth of maximum velocity, but it deviates from the experimental data above the maximum velocity point due to velocity-dip phenomenon, and that the velocity profile of the outer region is more influenced by the Froude number than the roughness. It is also shown that both the velocity difference between maximum velocity and surface velocity and the ratio of the average velocity to surface velocity become larger as the Froude number increases.