• Journal of the Korea Furniture Society
• /
• v.21 no.2
• /
• pp.188-195
• /
• 2010

This study has been focused on the evaluation of domestic softwood timbers to replace imported timbers for woodcrafts and furniture-making. Figures on radial and tangential sections were observed with naked eyes. As the result of study on the figures appeared on the wood surface of 6 species of trees, flat grain and edge grain were clearly found from Taxus cuspidata. Juniperus chinensis and Ginkgo biloba had wavy grain figure and pigment figure, and blister figure was found in Pinus densiflora, Larix kaempferi showed pitch streak and irregular figures on its tangential section due to growth abnormalities. Wavy grain figure appeared weakly on near knot of Pinus koraiensis. The characteristic figures shown from each species of trees are expected to be used for crafts, sculptures, furniture, and interior decoration. They are also considered to have great potential to substitute imported timber sufficiently, which are currently used a lot for wood crafts and furniture-making.

• Journal of the Korea Furniture Society
• /
• v.22 no.3
• /
• pp.239-243
• /
• 2011

In this study, the coating properties and surface performance of exotic cherry wood (Prunus serotina) were estimated, reviewing color difference, hardness and abrasion resistibility in order to evaluate probability as construction interior members such as wall and floor. The reduction effect of color difference was represented in the order of water soluble color stain, water soluble transparent stain, and non-coated lumber. However, the tendency of distinct difference according to wood grain pattern was not found. The wavy grain lumber showed better properties in hardness and resistance to abrasion than quarter grain. In conclusion, it was supposed that the application of wavy grain lumber in wall and floor as interior materials would be acceptable in practicality.

• The Journal of the Petrological Society of Korea
• /
• v.11 no.2
• /
• pp.65-73
• /
• 2002

The wavy extinction of quartz grains can be used as a good indicator to show the degree of rock deformation. To determine degree of the rock deformation, intensity of wavy extinction (IWE) of quartz grains was measured by using polarizing microscope, digital camera, and NIH image (or Scion Image). In this experiment, the measurement was performed along the line perpendicular to the subgrain boundary of wavy extinction. IWE was measured when a quartz grain shows maximum extinction in polarizing microscope. NIH image was represented in terms of 256 gray-scale brightness, which was associated with intensity of the wavy extinction. IWE was determined by the degree of brightness versus the measuring length of a quartz grain. IWE was analysed in the distribution chart with the collection unit of 5. Regarding the characteristics of data distribution, the median between the mode and the median of the histogram is defined as a representative value for the IWE, and this value is subdivided into the five levels of rock deformation zones (lowest- or non-, low-, medium-, high-, and highest deformation) with their respective indices (D1, D2, D3, D4, and D5). The correlation between the Eonyang Granite and the Yangsan Fault was investigated by using the indices. The results indicate that IWE values decreased away from the fault.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.5
• /
• pp.391-398
• /
• 2010

In this study, the figure of domestic hardwood was observed using the naked eye and the possibility of substituting imported wood with domestic one in the making woodcraft or furniture was investigated. It was known from the investigation on 8 different hardwoods that there were various figures such as cloud-shaped figure, blister figure, crotch figure, bird's eye figure, etc. in Zelkova serrata wood and the beautiful pigment figure in Diospyros Kaki wood. There were the unusual figures such as wavy grain figure, fiddle back figure, etc. in Cedrela sinensis wood and was clear ray-fleck figure in Quercus variabilis wood. There were also various figures such as wavy grain figure, blister figure, pigment figure, etc. in Sophra japonica, Tilia amurensis, Castanea crenata, Kalopanax septemlobus wood, etc. It is thus that distinguished figures appeared in each kind of wood can be used for craft, sculpture, furniture, and interior material. These kinds of figures can also be used for instrument, toy, stationery, life article material and souvenir, etc. And it can be expected that they will replace the imported wood has been mainly used to make the woodcraft or furniture until now.

• The Journal of the Petrological Society of Korea
• /
• v.12 no.3
• /
• pp.101-109
• /
• 2003

The wavy extinction of quartz can be used as a standard indicator showing the degree of rock deformation. In determine the degree of rock deformation, the intensity of wavy extinction (IWE) of quartz was measured using polarizing microscope, digital camera, and NIH Image program. This method was applied to the granite of Pocheon-Gisanri area, which are divided three type; biotite granite (Gb), garnet biotite granite (Ggb) and two mica granite (Gtm). In this study, measurement of wavy extinction was proceeded Ggb in eastern part and Gb in western part based on the Pocheoneup. The result was that Gb shows low deformation degree below D2, and Ggb represents high deformation degree above D3, generally showing that increasing deformation degree from northwest to southeast in the studied area. It is suggested that the fault which penetrated Ggb in 1/250,000 geological map affected the deformation degree of Ggb.

• Journal of Korea Foundry Society
• /
• v.22 no.1
• /
• pp.11-16
• /
• 2002

Hot deformation behavior of GCD-50 cast iron has been investigated by employing the compressive test. Phenomenological deformation behaviors, which were modeled based on the dynamic materials model and the kinetic model, have been correlated with the microstructural change taken place during compression. Microstructural investigation revealed that the adiabatic shear band caused by the locallized deformation was taken place in low temperature and high strain rate. On the other hand, the wavy and curved grain boundaries, which repersent the occurrence of dynamic microstructure change such as dynamic recovery and dynamic recrystallization, were observed in high temperature and low strain rate. Deformation model based on hyperbolic sine law has also been suggested.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.9 no.2
• /
• pp.33-42
• /
• 1972

This paper was studied on the behavior, crack formation and propagation of slip bands on low carbon steel which was heat-treated in three conditions in order to change metallic structure. The specimens were tested by rotating bending fatigue testing machine and also observed the variations of grains by microscope. From the test results it was clear that fatigue endurance limit and life of low carbon steel were more increased in contrast with the case that the grain size of specimen was more decreased. Slip bands developed at oil-quenched specimen and furnace-cooled specimen. Formed cracks in the first one or two grains below the surface were approximately "planar" type, there after they followed "wavy" type. It was also found that cracks at 30% higher stress than fatigue limit were usually developed inter-granular, and cracks at 12% higher stress than fatigue limit were propagated meandering path, partly trans- and partly inter-grandular.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.1
• /
• pp.32-36
• /
• 2021

This study was investigated in carbon diffusion behavior of laser-carburized TiZrN coating layer and the changes of mechanical properties. The carbon paste was deposited on TiZrN coatings, and the laser was irradiated to carburize into the coatings. The XRD peak corresponding to the (111) plane shifted to a lower angle after the carburization, showing the lattice expansion by doped carbon. The decreased grain size implied the compression by the grain boundary diffusion of carbon. The XPS spectra for the bonding states of carbon was analyzed that carbon was substitute to nitrogen atoms in TiZrN, as carbide, through the thermal energy of laser. In addition, the combination of sp2 and sp3 hybridized bonds represented the formation of an amorphous carbon. The cross-sectional TEM image and the inverse FFT of the TiZrN coating after carburizing were observed as the wavy shape, confirming the amorphous phase located in grain boundaries. After the carburization, the hardness increased from 34.57 GPa to 38.24 GPa, and the friction coefficient decreased by 83 %. In particular, the ratio of hardness and elastic modulus (H/E) which is used as an index of the elastic recovery, increased from 0.11 to 0.15 and the wear rate improved by 65 %.

• Journal of Energy Engineering
• /
• v.13 no.4
• /
• pp.281-290
• /
• 2004

Spent refractories from a coal gasifier after 1000 hours of operation were analyzed for crystalline phases, chemical composition and microstructures as a function of slag penetration depth, and the slag corrosion mechanism was determined. The chemical corrosion of chromia refractory occurred via reaction between Cr$_2$O$_3$ of the refractory and FeO and A1$_2$O$_3$ in the slag. The FeO reacted with Cr$_2$O$_3$ at the slare/refractory interface and formed FeCr$_2$O$_4$. After all FeO were consumed, Al in the penetrating slag substituted Cr in Cr$_2$O$_3$, forming (Al, Cr)$_2$O$_3$, at the edges of the particle, which were broken to form fragments rich in Al. The corrosion resistance of Cr$_2$O$_3$ varied with the particle size and the extent of sintering, and the higher resistance was observed in the larger and more sintered particles. There was no chemical change in ZrO$_2$, but showed the effects of physical corrosion: the grain boundaries became more wavy, and ZrO$_2$ grains were split in the corroded area. The slag penetration depth increased in the refractory samples farther down from the feed nozzles.