• Journal of the Korean Wood Science and Technology
• /
• 제49권4호
• /
• pp.328-335
• /
• 2021

Considerable differences exist in the characteristics of size reduction and classification because of biomass species. Miscanthus sacchariflorus (M. sacchariflorus) Goedae-Uksae 1 is not used efficiently because of the imperfections of the processing technology for this biomass. Therefore, for the best use of specific biomass, improvement in the feedstock preparation of the biomass for processing, such as pellet manufacturing, is necessary. In this study, a laboratory-scale cone grinder and air classifier were designed and combined to investigate the performance of the combination system for M. sacchariflorus. The average equivalent spherical diameter of particles showed a close relationship with air velocity for air classification. The air velocity range to classify proper particles for pelletization was determined to be 6.0-6.8 m/s. The mass ratios of the collected particles to feed mass for four lengths of chopped M. sacchariflorus were 45.1%:46.1%, 39.1%:46.6%, and 44.1%:52.8% at the first, second, and third steps in simulating the multistep combination system, respectively.

• Journal of the Korean Wood Science and Technology
• /
• 제43권2호
• /
• pp.156-167
• /
• 2015

The aim of this study was to determine the physical and mechanical properties of glued laminated timber (glulam) manufactured from small-diameter logs of three wood species, Acacia mangium (mangium), Maesopsis eminii (manii), and Falcataria moluccana (sengon), with densities of 533, 392, and $271kg/m^3$, respectively. Glulam measuring 5 cm by 7 cm by 160 cm in thickness, width, and length, respectively, was made with three to five lamina, or layers, and isocyanate adhesive. The glulams contained either the same wood species for all layers or a combination of mangium face and back layers with a core layer of manii or sengon. Solid wood samples of the same size for all three species were included as a basis for comparison. Physical-mechanical properties and delamination tests of glulam referred to JAS 234:2003. The results showed that the properties of same species glulam did not differ from those of solid wood, with the exception of the shear strength of glulam being lower than that of solid wood. Wood species affected glulam properties, but three- and five-layer glulams were not different except for the modulus of elasticity. All glulams were resistant to delamination by immersion in both cold and boiling water. The glulams that successfully met the JAS standard were three- and five-layer mangium, five-layer manii, and five-layer mangium-manii glulams.

• Journal of the Korean Wood Science and Technology
• /
• 제43권6호
• /
• pp.701-713
• /
• 2015

소나무와 금강송의 수종 분류를 위해 근적외선(NIR) 분광법과 주성분분석(PCA) 및 부분최소자승법 판별분석(PLS-DA)을 결합하여 수종 분류 모델을 설계하였다. 측정된 모든 NIR 스펙트럼을 이용하여 PCA를 실시한 결과 소나무와 금강송의 수종 분류는 불가능하였다. 그러나 2차 미분된 스펙트럼을 이용하여 시험편의 단면과 심 변재 구분에 따른 수종 분류에서는 변재부에서 수종 분류가 가능하였으며, 특히 방사단면의 변재에서는 명확하게 수종이 분류되었다. 그리고 개발된 PLS-DA 예측 모델을 통해 명확한 수종 분류가 가능하였다. 2차 미분으로 전처리된 스펙트럼을 이용하였을 때 가장 좋은 분류 결과 얻을 수 있었다. 2차 미분 스펙트럼을 이용한 예측 모델은 100%의 분류 정확도를 나타내었으며, 예측 모델의 $R_p{^2}$ 값은 0.86, RMSEP는 0.38로 나타났다. 전처리하지 않은 스펙트럼과 2차 미분 스펙트럼을 이용한 예측 모델의 신뢰도는 유사하였다. 근적외선 분광법과 부분최소자승법 판별분석을 결합한 수종 분류 모델은 소나무와 금강송의 분류에 적합하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제42권5호
• /
• pp.516-522
• /
• 2014

Old architectural wood materials damaged by a fire were evaluated on the basis of wood species and scanning electron microscopy (SEM) observation of wood tissues in combination with energy dispersive X-ray spectroscopy (EDXS) analysis. Results of SEM observation showed that tracheid wall thickness of burned parts was very thin compared with undamaged and sound wood, and tylosoid in the resin canals disappeared after the exposure to fire. SEM-EDXS analysis indicated that carbon and oxygen peaks occurred in the original energy band, and the carbon peak was higher than that of the oxygen in the burned part. A computerized tomography was also undertaken to investigate the carbonization layer formed by fire and possible internal defects.

• Journal of the Korean Wood Science and Technology
• /
• 제26권1호
• /
• pp.63-69
• /
• 1998

This study was carried out to get some basic information on mechanical properties of Korea Lepidobalanus for rational utilization of wood. Five species of Quercus variabilis, Q. aliena, Q. serrata, Q. mongolica, Q. acutissima belong to Lepidobalanus were investigated in this research. Relationship of anatomical characteristics to compression strength parallel to grain was analyzed using stepwise regression technique. All possible combination of 21 independent variables were regressed on compression strength parallel to grain. The summarized results in this study were as follows: I. In the proportion of wood structural elements, the factors that had the greatest influence on compression strength parallel to grain appeared to be proportion of ray in earlywood in Q. variabilis and Q. acutissima, proportion of wood fiber in latewood in Q. aliena and Q. serrata and proportion of vessel in earlywood in Q. mongolica respectively. 2. In the size of wood element and its structure, the factors that had the greatest influence on compression strength parallel to grain were microfibril angle in Q. variabilis, Q. serrata and Q. mongolica and length of wood fiber in Q. aliena and Q. acutissima.

• Journal of the Korean Wood Science and Technology
• /
• 제51권2호
• /
• pp.81-97
• /
• 2023

The aim of this study were to evaluate tannin resorcinol formaldehyde (TRF) for the preparation of cross-laminated timbers (CLTs) made from fast-growing tree species and to analyze the physical and mechanical properties of CLTs. TRF copolymer resin was prepared by using the bark extracts of Swietenia mahagoni (L.) Jacq. It was observed that the TRF adhesive possessed less solid content (23.59%), high viscosity (11.35 poise), and high pH values (10.0) compared to the standard phenol resorcinol formaldehyde. The TRF adhesive was applied to produce CLTs with the addition of 15% tapioca and flour as an extender. The six-layered CLTs were produced from sengon (Falcataria moluccana Miq.), jabon [Anthocephalus cadamba (Roxb) Miq.], coconut (Cocos nucifera L.), and the combination of coconut-jabon and coconut-sengon wood. The analysis of variance revealed that the layer composition of CLT significantly affected the physical and mechanical properties of the beam. While the modulus of rupture met the standard, the moisture content and modulus of elasticity values did not fulfill JAS 1152-2007. All of the CLTs produced in this study demonstrated low formaldehyde emission, ranging from 0.001 mg/L to 0.003 mg/L, thereby satisfying the JAS 1152 for structural glue laminated timber.

• Journal of the Korean Wood Science and Technology
• /
• 제30권4호
• /
• pp.58-65
• /
• 2002

본 연구는 수액치환법을 이용한 침엽수 간벌소경재나 미(저)이용 활엽수재의 산지 보존처리 기술을 개발하기 위하여 수행되었다. 본 논문에서는 증산법과 원구법을 이용한 3종 침엽수와 3종 활엽수의 방부제, 난연제, 치수 안정제 처리 가능성을 조사하여 보고한다. 수종과 처리약제의 조합에 관계없이 원구법이 증산법에 비하여 약제의 목재내 침투가 양호할 뿐만 아니라 약제의 침투가 균일한 관계로 수분 이동경로를 이용한 처리재 생산은 원구법의 사용이 바람직하였다. 원구법 처리는 수관부를 절단한 후 실시하기 때문에 증산법에 비하여 처리가 용이할 뿐만 아니라 벌채 및 조재 후 산지의 일정 장소로 운재 후 처리를 실시하기 때문에 증산법과 비교할 때 집약적 처리로 단위시간당 처리재 생산량이 높고 산지 환경오염 문제도 예방할 수 있는 장점이 있다.

• Mycobiology
• /
• 제42권2호
• /
• pp.114-119
• /
• 2014

The wood decay fungi Antrodia P. Karst. play important ecological roles and have significant industrial and economic impacts as both wood degraders and sources of pharmaceutical and biotechnological products. Although each Antrodia species has distinct morphological characteristics, the misidentification rate is especially high due to their simple morphological characters. A combination of morphological and internal transcribed spacer region sequence analyses revealed that 27 of 89 specimens previously identified by morphology alone were correct, whereas 35 of these specimens were misidentified as other Antrodia species. We report here that seven Antrodia species exist in Korea (A. albida, A. heteromorpha, A. malicola, A. serialis, A. sinuosa, A. sitchensis, and A. xantha) and based on these specimens, we provide taxonomic descriptions of these species, except for A. serialis, which was only confirmed by isolate.

• Journal of the Korean Wood Science and Technology
• /
• 제48권4호
• /
• pp.513-526
• /
• 2020

The existing preservation methods are difficult to be applied to a large dimension log which is needed for making traditional wooden ship 'Jalur' in Riau Province. Novel techniques to provide the use of readily available species to replace traditional species alternative were investigated. These included infusion and a combination of injection and bandage-wrapping methods for preserving living trees of Balam (Macaranga conifera (Rchb.f. & Zoll.) Müll.Arg.) and Bintangor (Calophyllum soulattri Burm.f.). Water-based boron compounds were applied as wood preservatives. In total, 18 discs from the bottom, middle, and top of four trees and two controls were used. Trees undergoing treatment were also used to see how wood anatomical structure might affect the boron penetration. The overall aim was to identify the best method for use in Jalur manufacturing. The results showed that in infused Balam tree where the hose position for the preservative intake was deep (10-15 cm from the bark), no boron compound was observed in the outer sapwood. Combination of injection and bandage-wrapping method gave higher percentage of boron penetration at bottom and middle of Balam tree. However, infused Bintangor showed 100% boron penetration. The larger vessel diameter, the absence of tyloses, and the simple perforation plates in Bintangor wood were likely to have contributed to the higher penetration of boron. The combination of bandage-wrapping and infusion, or alternatively by infusing the living trees close to the bark, and at as low as position in the stem gives better protection when treatments are applied to living trees.

• Mycobiology
• /
• 제50권1호
• /
• pp.46-54
• /
• 2022

Although Apiospora Sacc. has previously been considered a sexual morph of Arthrinium species on the basis of phylogenetic, morphological, and ecological diagnoses, a recent study delimited these as different species. Recently, 14 species, including eight new species, of marine Arthrinium have been reported from Korea. Six known species have previously been renamed as species in the genus Apiospora (A. arundinis, A. marii, A. piptatheri, A. rasikravindrae, A. sacchari, and A. saccharicola). However, the eight new species of marine Arthrinium (Ar. agari, Ar. arctoscopi, Ar. fermenti, Ar. koreanum, Ar. marinum, Ar. pusillispermum, Ar. sargassi, and Ar. taeanense) are yet to be studied, and thus the taxonomic status of these species remains to be clarified. In this study, we conducted phylogenetic analyses using the internal transcribed spacer, 28S large subunit ribosomal RNA gene, translation elongation factor 1-alpha, and beta-tubulin regions to confirm the phylogenetic position of these eight species. Based on these analyses, we re-identified the eight Arthrinium species as new combinations in Apiospora. Additionally, among the six known Apiospora species, two (A. piptatheri and A. rasikravindrae) have not previously been recorded in Korea. On the basis of morphological and molecular analyses, we report these as new species in Korea. Herein, we present scanning electron micrographs detailing the morphologies of these species, along with phylogenetic trees and detailed descriptions.