Journal of the Korean GEO-environmental Society (한국지반환경공학회 논문집)

Korean Geo-Environmental Society (한국지반환경공학회)
권호 표지

Analysis Model of Corrugated Steel Plates for Soil-Metal Box Culverts

지중강판 박스구조물을 위한 파형강판 해석 모델

  • 최동호 (한양대학교 공과대학 건설환경공학과) ;
  • 이종선 (한양대학교 공과대학 건설환경공학과) ;
  • 나호성 (한양대학교 공과대학 건설환경공학과)
  • Received : 2009.09.02
  • Accepted : 2010.10.05
  • Published : 2010.11.01
Download PDF
⟨ Previous Next ⟩

Abstract

In this paper, a 3-dimensional stiffened plate model for soil-metal box structures is proposed. 3-dimensional stiffened plate model is enable to model corrugated steel plates of soil metal box culverts considering section modulus and section properties of longitudinal and horizontal direction from a corrugated steel plate. Loading conditions which causes maximum displacement and maximum moment according to the step construction stages(a back filling to the top of the plate, a back filling to the maximum depth of cover, and loading of live loads) was applied and the behaviors of the soil metal box culverts was analyzed. Analysis results of 3-dimensional stiffened model were compared with those of 2-dimensional model, 3-dimensional equivalent plate model and 3-dimensional corrugated plate model. As results, the behaviors of 2-dimensional model and 3 dimensional equivalent model are different from 3-dimensional corrugated plate model but the result of 3-dimensional stiffened model has good agreement with that of 3-dimensional corrugated plate model.

본 연구에서는 지간 15m 이하의 지중파형강판 박스구조물의 3차원 해석 시 적용 가능한 3차원 보강판 모델을 제안하고 검증하였다. 3차원 보강판 모델은 실제 파형강판의 단면계수와 종방향과 길이방향의 단면특성을 고려하여 지중강판 박스구조물을 모델링함으로써, 3차원 해석 시 모델링을 간편하게 하고 해석시간을 단축할 수 있는 유용한 해석 모델이다. 이 모델을 검증하기 위해 3단계의 시공과정(정점부까지의 뒷채움, 토피고까지의 뒷채움, 활하중재하)에 따른 거동분석으로부터 최대 변위와 최대모멘트를 유발하는 재하상태를 도출하였고, 제안된 단면을 통해 파형강판의 거동을 분석하였다. 분석 결과를 3차원 등가판 모델, 2차원 모델, 실제파형강판 구조물과 동일하게 모델링한 3차원 Corrugated 판 모델과 비교 검증하였다. 해석결과 2차원 모델과 3차원 등가판 모델은 활하중 조건에서 3차원 Corrugated 판 모델과 큰 차이를 나타내었으나, 3차원 보강판 모델은 모든 해석 결과에서 3차원 Corrugated 판 모델과 일치하는 결과를 나타내었다.

Keywords

Acknowledgement

Supported by : 한국연구재단

References

  1. 최동호, 이승재, 조용우, 박상일(2006), 장지간 지중강판 박스 구조물의 휨모멘트 계수식 제안, 대한토목학회 논문집, Vol.26, No. 1A, pp. 133-142.
  2. 최우람(2008), 장지간 파형강판 박스형 구조물의 3차원 구조해석모델 개발, 석사학위논문, 한양대학교, pp. 11-50.
  3. AASHTO(2002), Standard Specification for Highway Bridges, American Association of State Highway and Transfortation Officials, Washington, D. C., pp. 12-1 - 12-83.
  4. Boulanger, R. W., Seed, R. B., Baird, R. D., and Schluter, J. C.(1989), Measurements and Analysis of Deformed Flexible Box Culverts, Transportation Research Record 1231, Transportation Research Board, National Research Council, Washington, D. C., pp. 25-25.
  5. Canadian Standards Association(2000), Canadian Highway Bridge Design Code, Ministry of Transportation of Canada, Canada, pp 271-282.
  6. Choi, D. H., Kim, G. N. and Peter, B. M.(2004), Evaluation of Moment Equation in the 2000 Canadian Highway Bridge Design code for Soil-metal Arch Structures, Canadian Journal of Civil Engineering, National Research Council of Canada, Vol. 31, No. 2, pp. 281-291. https://doi.org/10.1139/l03-097
  7. Davis, J. M.(1977), Simplified Diaphragm Analysis, Journal of the Structural Division, ASCE, Vol. 103, No. 11, pp. 2093-2109.
  8. Duncan, J. M. and Chang, C. Y.(1970), Nonlinear Analysis of Stress and Strain in Soils, Journal of the Soil Mechanics and Foundations Division, ASCE, Vol. 96, No. 5, pp. 1629-1653.
  9. Duncan, J. M., Seed, R. B. and Drawsky R. H.(1985), Design of Corrugated Metal Box Culverts, Transportation Reasearch Record 1008, Transportation Research Board, National Research Council, Washington, D. C., pp. 33-41.
  10. EI-Sawy, K. M.(2003), Three-Dimensional Modeling of Soil-Steel Culverts under the Effect of Truckloads, Thin-Walled Structures, Elsevier Science, Vol. 41, No. 8, pp. 747-768. https://doi.org/10.1016/S0263-8231(03)00022-3
  11. Machelski, C. Z. and Antoniszyn, G.(2004), Influence of Live Loads on the Soil-steel Bridge, Studia Geothechnica et Mechanica, Oficyna Wydawnicza Politechniki Wrocławskiej, Vol. 104, No.3-4, pp. 90-119.
  12. Mang, H. S., Jimmy H. S. and Girya C. V.(1976), Finite Element Analysis of Doubly Corrugated Shells, Journal of the Structural Division, ASCE, Vol. 102, No. 10, pp. 2033-2050.
  13. McCavour, T. C., Byrne P. M. and Morrison, T. D.(1998), Long- Span Reinforced Steel Box Culverts, Transportation Research Record 1624, Transportation Research Board, National Research Council, Washington, D. C., pp. 184-195.
  14. Zhang, W., Saleh, A., Samali, B. and Ring, G.(2005), Study on the Behavior of Long Span Deep-Corrugated Reinforced Steel Box Culvert using Nonlinear Finite Element Method, 84th Annual Meeting and Proceedings of the TRB, Transportarion Research Board, Washington, D. C., CD-ROM.