The Transactions of The Korean Institute of Electrical Engineers (전기학회논문지)

The Korean Institute of Electrical Engineers (대한전기학회)
권호 표지
DOI QR코드

DOI QR Code

EM Analysis of High Voltage Connector for Hybrid/Electric Vehicle

하이브리드/전기 자동차용 고전압 커넥터의 전자기 해석

  • 이준상 (성균관대학교 정보통신공학부) ;
  • 김종민 (성균관대학교 정보통신공학부) ;
  • 남기훈 (성균관대학교 정보통신공학부) ;
  • 배현주 (성균관대학교 정보통신공학부) ;
  • 성진태 ((주)유라코퍼레이션 기술연구소) ;
  • 나완수 (성균관대학교 정보통신공학부)
  • Received : 2010.09.13
  • Accepted : 2010.11.18
  • Published : 2011.01.01
Download PDF
⟨ Previous Next ⟩

Abstract

This paper analyzes EM(Electromagnetic) characteristic in the high voltage connector for the hybrid electric vehicle. The connector bridges the electrical components and helps transferring electrical power and signal through it. The necessity of the high voltage and current connector development is emphasized because the hybrid electric vehicle recently uses the high voltage and current more than 500V and 80A. So far there has not been international EMC (Electromagnetic Compatibility) standards to limit the RE(Radiation Emission) from the connector for the hybrid electric vehicle. In this paper we analyzed EM characteristic of the 288V, 65A connector to check if the RE from the high voltage connector could be within the RE limit standard of vehicle. Three-dimensional modeling and simulation was conducted by using MWS(Microwave Studio) of the CST corporation, and the result was compared with the measured RE data, which showed good coincidence each other.

Keywords

References

  1. C.C. Chan, "The State of the Art of Electric, Hybrid, and Fuel Cell Vehicles", Proceedings of the IEEE, April 2007
  2. Yakup Bayram, "High Power EMI on Digital Circuits within Automotive Structures", IEEE International Symposium on Electromagnetic Compatibility, August 2006
  3. P. Andersen, "The present status of the international automotive EMC standards", IEEE International Symposium on Electromagnetic Compatibility August 2009
  4. Youn Hee Lee, Adel Nasiri, "Analysis and modeling of conductive EMI noise of power electronics converters in electric and hybrid electric vehicles," Twenty-Third Annual IEEE on Applied Power Electronics Conference and Exposition
  5. Jody J. Nelson1, William Goodwin, Mark Steffka, William Ivan, Markus Kopp, "High Voltage Automotive EMC Component Measurements Using an Artificial Network", 18th International Zurich Symposium on Electromagnetic Compatibility, September 2007
  6. Heinz Rebholz, Stefan Tenbohlen, "A fast radiated emission model for arbitrary cable harness configurations based on measurements and simulations", IEEE International Symposium on Electromagnetic Compatibility, August 2008
  7. Allen Taflove, Susan Hagness, "Computational Electrodynamics: The Finite-Difference Time-Domain Method", Artech House, Boston, MA, 2000
  8. Takuji Arima, Toru Uno, "Modification of FDTD Method for Highly Accurate Analysis of Microstrip Lines using Quasi-static Approximation", IEEE Antennas and Propagation Society International Symposium, July 2006
  9. 자동차 및 불꽃점화 엔진구동 기기류 기술기준 및 시험방법 초안 (KN 41)

Cited by

  1. Anaysis of Small-sized Power Connectors for Mobile Device Batteries vol.19, pp.1, 2015, https://doi.org/10.7471/ikeee.2015.19.1.101
  2. Impact Safety Control Strategy for the Battery System of an Example Electric Bus vol.2015, 2015, https://doi.org/10.1155/2015/123626