Journal of Welding and Joining

  • 제33권2호
  • /
  • Pages.85-90
  • /
  • 2015
  • /
  • 2466-2232(pISSN)
  • /
  • 2466-2100(eISSN)
대한용접접합학회 (The Korean Welding and Joining Society)
권호 표지
DOI QR코드

DOI QR Code

강의 레이저-아크 하이브리드 용접시 공정변수에 따른 비드용접특성 (I) - 보호가스 유량 및 레이저 아크간 거리의 영향 -

The characteristics of bead welding on steel with process parameter during the laser-arc hybrid welding(I) - Effect of flow rate of shield gas and distance between laser and arc -

  • 김종도 (한국해양대학교 기관공학부) ;
  • 명기훈 (한국해양대학교 대학원 기관공학과) ;
  • 송무근 (한국해양대학교 대학원 기관공학과) ;
  • 오재환 (세화산업) ;
  • 서정 (한국기계연구원 부산레이저기술지원센터)
  • Kim, Jong-Do (Division of Marine Engineering, Korea Maritime and Ocean Univ.) ;
  • Myung, Gi-Hoon (Graduate School, Korea Maritime and Ocean Univ.) ;
  • Song, Moo-Keun (Graduate School, Korea Maritime and Ocean Univ.) ;
  • Oh, Jae-Hwan (Sae-Hwa Industry) ;
  • Suh, Jeong (Busan Laser Application Support Center, Korea Institute of Machinery & Materials)
  • 투고 : 2015.04.17
  • 심사 : 2015.04.29
  • 발행 : 2015.04.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Recently many studies for improvement of productivity and automation of process are in progress, and among others, laser-arc hybrid welding that combined laser and arc has attracted much attention. Since parameters by interactions as well as the parameters of each heat source should be considered, There are a lot of hardship in actual application, even though many researches have been done so far. Therefore in this study, bead welding was done to examine the effects of the flow rate of shield gas and the distance between laser and arc during laser-arc hybrid welding. As for hybrid heat source, disk laser and MIG were used. As experiment result, sound bead and weld with no defect were formed when the flow rate of front and rear shield gas were respectively 20 l/min and 15 l/min, and deep penetration was done at DLA=3 mm.

키워드

참고문헌

  1. Ming Gao, Xiaoyan Zeng and Qianwu Hu : Effect of gas shielding parameters on weld penetration of $CO_2$ laser-TIG hybrid welding, Journal of Materials Processing Technology, 184(1-3) (2007), 177-183 https://doi.org/10.1016/j.jmatprotec.2006.11.019
  2. S. Tetsuo, M. Yasuo, K. Taizo, U. Tomoyuki and U. Yuji : Research on laser arc hybrid welding of HT780 Steel, Journal of the Japan Welding Society, 29(4) (2011), 248-257 (in Japanese) https://doi.org/10.2207/qjjws.29.248
  3. G. Campana, A. Fortunato, A. Ascari, G. Tani and L. Tomesani : The influence of arc transfer mode in hybrid laser-MIG welding, Journal of Material Processing Technology, 191 (2007), 111-113 https://doi.org/10.1016/j.jmatprotec.2007.03.001
  4. Cheol-Hee Kim, Hyun-Byung Chae, Jun-Ki Kim and Jeong-Han Kim : Welding Phenomena in Laser-GMA Hybrid Welding Process with and without Arc Rotation, Journal of KWS, 24(3) (2006), 15-21 (in Korean)
  5. Liu Zhongjie : $CO_2$ laser-MAG hybrid welding of 590MPa high strength steel, Journal of The Japan Welding Society, 24(1) (2006), 17-25 (in Japanese) https://doi.org/10.2207/qjjws.24.17
  6. Ming Gao, Shuwen Mei and Zemin Wang : Process and joint characterizations of laser-MIG hybrid welding of AZ31 magnesium alloy, Journal of Materials Processing Technology, 1338-1346 (2012)
  7. J. Tusek and M. Suban : Hybrid welding with arc and laser beam, Sci. Technol. Weld. Joining, 308-311 (1999)
  8. Liming Liu, Minghua Chen : Effect of electric arc on laser keyhole behavior based on direct observation during low power pulsed laser-arc hybrid welding process, Optics and Lasers in Engineering, 51 (2013), 1153-1160 https://doi.org/10.1016/j.optlaseng.2013.04.010
  9. Jing-bo Wnag and Hitoshi Nishimura : Study of improvement of gap tolerance in laser-MIG arc hybrid welding of aluminium alloy, Journal of Light Metal Welding, 46(10) (2009), 447-458
  10. J. Matsuda, A. Utsumi and M. Hamasaki : TIG or MIG arc augmented laser welding of thick mild steel plate, Joining and Materials, 1, No. 1(1988), 31-34
  11. M. Kutsuna and L. Chen : Interaction of both plasmas in $CO_2$ laser-MAG hybrid welding of carbon steel, Proceeding of SPIE, 4831(2003), 357-362

피인용 문헌

  1. An Analytical Study on the Preheating Effect of Flat Workpiece in Thermally Assisted Machining by Multi Heat Sources vol.33, pp.8, 2016, https://doi.org/10.7736/KSPE.2016.33.8.629