한국정밀공학회지 (Journal of the Korean Society for Precision Engineering)

  • 제32권6호
  • /
  • Pages.503-507
  • /
  • 2015
  • /
  • 1225-9071(pISSN)
  • /
  • 2287-8769(eISSN)
한국정밀공학회 (Korean Society for Precision Engineering)
권호 표지
DOI QR코드

DOI QR Code

소재와 나사산 변화에 따른 정밀나사의 체결력 향상에 관한 연구

A Study on the Clamping Improvement of Precision Screws according to the Materials and Thread Changes

  • 투고 : 2015.05.15
  • 심사 : 2015.05.26
  • 발행 : 2015.06.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

In this study, we compare the performance of the screw through the Clamping force of the test materials to change shape and structure, one of the ways to maintain and improve the engaging force to cope with the miniaturization of the fastener threads are further thinner and lighter precision way that can improve the fastening force of the screw results were as follows. The clamping force according to the materials was $7.57N{\cdot}cm$ in SUS XM7 and SWCH18A was $5.97N{\cdot}cm$. This result was to be found to average 13.5% high in the Clamping force of SUS XM7 materials. In the case of the clamping force of the screw thread shape change, the clamping force of symmetrical and asymmetrical thread was $6.78N{\cdot}cm$ and $7.57N{\cdot}cm$. The clamping force of the asymmetrical thread showed an average high of 11.6%.

키워드

참고문헌

  1. Bickford, J. H., "An Introduction to the Design and Behavior of Bolted Joints" CRC Press, 3rd Ed., 1995.
  2. Min, K. B., Kim, J. B., Park, K., and Ra, S. W., "Evaluation of Clamping Characteristics for Subminiature Screws according to Thread Angle Variation," J. Korean Soc. Precis. Eng., Vol. 31, No. 9, pp. 839-846, 2014. https://doi.org/10.7736/KSPE.2014.31.9.839
  3. Yan, Y., Wen, W.-D., Chang, F.-K., and Shyprykevich, P., "Experimental Study on Clamping Effects on the Tensile Strength of Composite Plates with a Boltfilled Hole," Composites Part A: Applied Science and Manufacturing, Vol. 30, No. 10, pp. 1215-1229, 1999. https://doi.org/10.1016/S1359-835X(99)00002-0
  4. Drean, M., Habraken, A.-M., Bouchair, A., and Muzeau, J.-P., "Swaged Bolts: Modelling of the Installation Process and Numerical Analysis of the Mechanical Behaviour," Computers & Structures, Vol. 80, No. 27, pp. 2361-2373, 2002. https://doi.org/10.1016/S0045-7949(02)00240-7
  5. Izumi, S., Yokoyama, T., Iwasaki, A., and Sakai, S., "Three-dimensional Finite Element Analysis of Tightening and Loosening Mechanism of Threaded Fastener," Engineering Failure Analysis, Vol. 12, No. 4, pp. 604-615, 2005. https://doi.org/10.1016/j.engfailanal.2004.09.009
  6. Croccolo, D., De Agostinis, M., and Vincenzi, N., "Failure Analysis of Bolted Joints: Effect of Friction Coefficients in Torque-preloading Relationship," Engineering Failure Analysis, Vol. 18, No. 1, pp. 364- 373, 2011. https://doi.org/10.1016/j.engfailanal.2010.09.015
  7. Han, J. W., Kim, J. H., and Park, Y. S., "Evaluation of Structural Performance and Improvement of Screw Thread Shape on 1,300 MPa High Strength Bolts," Journal of the Korean Society of Civil Engineering, Vol. 31, No. 3A, pp. 189-198, 2011.
  8. Hwang, H. Y., "Bolted Joint Torque Setting using Numerical Simulation and Experiments," Journal of Mechanical Science and Technology, Vol. 27, No. 5, pp. 1361-1371, 2013. https://doi.org/10.1007/s12206-013-0317-2