DOI QR코드

DOI QR Code

Determination of strut efficiency factor for concrete deep beams with and without fibre

  • Sandeep, M.S. (Department of Civil Engineering, NIT Calicut) ;
  • Nagarajan, Praveen (Department of Civil Engineering, NIT Calicut) ;
  • Shashikala, A.P. (Department of Civil Engineering, NIT Calicut) ;
  • Habeeb, Shehin A. (Department of Civil Engineering, NIT Calicut)
  • 투고 : 2016.01.10
  • 심사 : 2016.06.28
  • 발행 : 2016.07.25

초록

Based on the variation of strain along the cross section, any region in a structural member can be classified into two regions namely, Bernoulli's region (B-region) and Disturbed region (D-region). Since the variation of strain along the cross section for a B-region is linear, well-developed theories are available for their analysis and design. On the other hand, the design of D-region is carried out based on thumb rules and past experience due to the presence of nonlinear strain distribution. Strut-and-Tie method is a novel approach that can be used for the analysis and design of both B-region as well as D-region with equal importance. The strut efficiency factor (${\beta}_s$) is needed for the design and analysis of concrete members using Strut and Tie method. In this paper, equations for finding ${\beta}_s$ for bottle shaped struts in concrete deep beams (a D-region) with and without steel fibres are developed. The effects of transverse reinforcement on ${\beta}_s$ are also considered. Numerical studies using commercially available finite element software along with limited amount of experimental studies were used to find ${\beta}_s$.

키워드

참고문헌

  1. ANSYS, Inc., ANSYS Help, Release 12.1, Documentation, Copyright 2006.
  2. ACI 318-14 (2014), Building code requirements for structural concrete and commentary, American Concrete Institute, USA.
  3. Andermatt, M.F. and Lubell, A.S. (2013b), "Strength modeling of concrete deep beams reinforced with internal fiber-reinforced polymer", ACI Struct. J., 110(4), 595-605.
  4. Bahen, N. and Sanders, D.H. (2009), "Investigation of strut strength using a deep-beam database", ACI Struct. J., SP-265(18), 385-404.
  5. Birrcher, D.B., Tuchscherer, R.G., Huizinga, M. and Bayrak, O. (2013), "Minimum web reinforcement in deep beams", ACI Struct. J., 110(2), 297-306.
  6. Brown, Michael, D., Sankovich, Cameron, L., Bayrak, Oguzhan and Jirsa, James, O. (2006), "Behavior and efficiency of bottle-shaped struts", ACI Struct. J., 103(3), 348-355.
  7. Chetchotisak, P., Teerawong, J. and Chetchotsak, D. (2014), "Efficiency factors for reinforced concrete deep beams: part 1-improved models", Adv. Mater. Res., 931-932, 506-513. https://doi.org/10.4028/www.scientific.net/AMR.931-932.506
  8. Chetchotisak, P., Teerawong, J. and Chetchotsak, D. (2014), "Efficiency factors for reinforced concrete deep beams: part2-code calibration", Adv. Mater. Res., 931-932, 514-519. https://doi.org/10.4028/www.scientific.net/AMR.931-932.514
  9. Chetchotisak, P., Teerawong, J. and Yindeesuk, S. (2014), "New strut-and-tie-models for shear strength prediction and design of RC deep beams", Comput. Concrete, 14(1), 19-14. https://doi.org/10.12989/cac.2014.14.1.019
  10. Choi, H.B., Yi, C.K., Cho, H.H. and Kang, K.I. (2010), "Experimental study on the shear strength of recycled aggregate concrete beams", Magaz. Concrete Res., 62(2), 103-114. https://doi.org/10.1680/macr.2008.62.2.103
  11. Dupont, D. and Vandewalle, L. (2003), "Shear capacity of concrete beams containing longitudinal reinforcement and steel fibers", Am. Concrete Inst. Spec. Pub., 216, 79-94.
  12. Hong, S. and Ha, T. (2012), "Effective capacity of diagonal strut for shear strength of reinforced concrete beams without shear reinforcement", ACI Struct. J., 109(2), 139-148.
  13. Hussein, Hayder, H. and Kamonna (2010), "Non-linear analysis of steel fibre reinforced concrete deep beams by ansys", Kufa J. Eng., 2(1), 110-124.
  14. Kim, D., Lee, J. and Lee, Y-H. (2014), "Effectiveness factor of strut-and-tie models for concrete deep beams reinforced with FRP rebars", Compos. Eng.: Part B, 56, 117-125. https://doi.org/10.1016/j.compositesb.2013.08.009
  15. Khan, M.A. and Ahmed, F.S. (2013), "Effect of web reinforcement on ultimate strength of reinforced concrete deep beam", Int. J. Eng. Res. Appl., 3(3), 516-519.
  16. Lihua, X.U., Yin, C.H.I., Jie, S.U. and Dongtao, X.I.A. (2008), "Nonlinear finite element analysis of steel fibre reinforced concrete deep beams", Wuhan Univ. J. Nat. Sci., 13(2), 201-206. https://doi.org/10.1007/s11859-008-0214-1
  17. Lu, W.Y., Hsiao, H.Tai., Chen, C.L., Huang, S.M. and Lin, M.C. (2015), "Tests of reinforced concrete deep beams", Comput. Concrete, 15(3), 357-372. https://doi.org/10.12989/cac.2015.15.3.357
  18. Mansur, M.A. and Ong, K.C.G. (1991), "Behavior of reinforced fibre concrete deep beams in shear", ACI Struct. J., 88(1), 98-105.
  19. Narayanan, R. and Darwish, I.Y.S. (1988), "Fibre concrete deep beams in shear", ACI Struct. J., 85(2), 141-149.
  20. Nagarajan, P. and Pillai, T.M.M. (2008), "Analysis and design of simply supported deep beams using strut and tie method", Adv. Struct. Eng., 11(5), 491-499. https://doi.org/10.1260/136943308786412050
  21. Nagarajan, P. and Pillai, T.M.M. (2008), "Development of strut and tie models for simply supported deep beams using topology optimisation", Songklanakarin J. Sci. Technol., 30(5), 641-647.
  22. Nagarajan, P. and Pillai, T.M.M. (2010), "Development of strut and tie models for continuous deep beams using topology optimisation", J. Struct. Eng., 37(4), 81-85.
  23. Nehdi, N., Omeman, Z. and EI-Chabib, H. (2008), "Optimal efficiency factor in strut-and-tie model for FRP-reinforced concrete short beams with (1.5 https://doi.org/10.1617/s11527-008-9359-9
  24. Quntero-Febres, C.G., Parra-Montesinos, G. and Wight, J.K. (2006) "Strength of struts in deep concrete members designed using strut-and-tie method", ACI Struct. J., 103(4), 577-586.
  25. Sahoo, D.K., Singh, B. and Bhargava, P. (2009), "An appraisal of the ACI strut efficiency factors", Magaz. Concrete Res., 61(6), 445-456. https://doi.org/10.1680/macr.2008.00112
  26. Sahoo, D.K., Singh, B. and Bhargava, P. (2010), "Strut efficiency factors for structural concrete made from coarse recycled concrete aggregates", J. Struct. Eng., 37(1), 49-54.
  27. Sahoo, D.K., Singh, B. and Pradeep Bhargava (2011), "Minimum reinforcement for preventing splitting failure in bottle-shaped struts", ACI Struct. J., 108(2), 206-216.
  28. Sahoo, D.K., Flores, C.A. and Chao, Shih-Ho (2012), "Behavior of steel fibre-reinforced concrete deep beams with large opening", ACI Struct. J., 109(2), 193-204.
  29. Schlaich, J., Schafer, K. and Jennewein, K. (1987), "Towards a consistent design of structural concrete", J. Prestress. Concrete Inst., 32(3), 75-150.
  30. Sclaich, J. and Schafer, K. (1991), "Design and detailing of structural concrete using strut-and-tie models", Struct. Eng., 69(6), 113-125.
  31. Tuchscherer, R., Birrcher, D., Huizinga, M. and Bayrak, O. (2011), "Distribution of stirrups across web of deep beams", ACI Struct. J., 108(1), 108-115.
  32. Wolanski, A.J. (2004), "Flexural behaviour of reinforced and prestressed concrete beams using finite element analysis", Master's Dissertation, Marquette University, Milwaukee.

피인용 문헌

  1. Development of Models for Predicting Strut Efficiency Factors for Conventional and Steel Fibre Reinforced Concrete Deep Beams vol.969, pp.None, 2016, https://doi.org/10.4028/www.scientific.net/msf.969.187