DOI QR코드

DOI QR Code

The effect of cyclic loading on the rubber bearing with slit damper devices based on finite element method

  • Saadatnia, Mahdi (Department of Civil Engineering, Najafabad Branch, Islamic Azad University) ;
  • Riahi, Hossein Tajmir (Department of Civil Engineering, Najafabad Branch, Islamic Azad University) ;
  • Izadinia, Mohsen (Department of Civil Engineering, Najafabad Branch, Islamic Azad University)
  • 투고 : 2020.01.02
  • 심사 : 2020.01.23
  • 발행 : 2020.02.25

초록

In this paper, slit steel rubber bearing is presented as an innovative seismic isolator device. In this type of isolator, slit steel damper is an energy dissipation device. Its advantages in comparison with that of the lead rubber bearing are its simplicity in manufacturing process and replacement of its yielding parts. Also, slit steel rubber bearing has the same ability to dissipate energy with smaller value of displacement. Using finite element method in ABAQUS software, a parametric study is done on the performance of this bearing. Three different kinds of isolator with three different values of strut width, 9, 12 and 15 mm, three values of thickness, 4, 6 and 8 mm and two steel types with different yield stress are assessed. Effects of these parameters on the performance characteristics of slit steel rubber bearing are studied. It is shown that by decreasing the thickness and strut width and by selecting the material with lower yield stress, values of effective stiffness, energy dissipation capacity and lateral force in the isolator reduce but equivalent viscous damping is not affected significantly. Thus, by choosing appropriate values for thickness, strut width and slit steel damper yield stress, an isolator with the desired behavior can be achieved. Finally, the performance of an 8-storey frame with the proposed isolator is compared with the same frame equipped with LRB. Results show that SSRB is successful in base shear reduction of structure in a different way from LRB.

키워드

참고문헌

  1. Abe, M., Yoshida, J. and Fujino, Y. (2004), "Multiaxial behaviors of laminated rubber bearings and their modeling. I: Experimental study", J. Struct. Eng., 130(8), 1119-1132. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:8(1119).
  2. Amadeo, B.C., Oh, S.H. and Akiyama, H. (1998), "Ultimate energy absorption capacity of slit-type steel plates subjected to shear deformations", J. Struct. Constr. Eng., 63(503), 139-147. https://doi.org/10.3130/aijs.63.139_1.
  3. ANSI A (2010), AISC 360-10, Chicago, Illinois, U.S.A.
  4. Asl, M.J., Rahman, M. and Karbakhsh, A. (2014), "Numerical analysis of seismic elastomeric isolation bearing in the base-isolated buildings", Open J. Earthq. Res. 3(1), 1. https://doi.org/10.4236/ojer.2014.31001.
  5. Bagheri, B., Choi, K.Y., Oh, S.H. and Ryu, H.S. (2016), "Shaking table test for evaluating the seismic response characteristics of concentrically braced steel structure with and without hysteretic dampers", Int. J. Steel Struct., 16(1), 23-39. https://doi.org/10.1007/s13296-016-3003-2.
  6. Bhuiyan, A.R., Okui, Y., Mitamura, H. and Imai, T. (2009), "A rheology model of high damping rubber bearings for seismic analysis: Identification of nonlinear viscosity", Int. J. Solid. Struct., 46(7-8), 1778-1792. https://doi.org/10.1016/j.ijsolstr.2009.01.005.
  7. Chan, R.W. and Albermani, F. (2008), "Experimental study of steel slit damper for passive energy dissipation", Eng. Struct., 30(4), 1058-1066. https://doi.org/10.1016/j.engstruct.2007.07.005.
  8. Choi, E., Nam, T.H. and Cho, B.S. (2005), "A new concept of isolation bearings for highway steel bridges using shape memory alloys", Can. J. Civil Eng., 2(5), 957-967. https://doi.org/10.1139/105-049.
  9. EN B (2010), 15129: 2009, Anti-Seismic Devices, BSI British Standards.
  10. Ghobarah, A. and Ali, H. (1990), "Seismic design of base-isolated highway bridges utilizing lead-rubber bearings", Can. J. Civil Eng., 17(3), 413-422. https://doi.org/10.1139/190-045.
  11. Haeri, A., Badamchi, K. and Tajmir Riahi, H. (2019), "Proposing a new hybrid friction-yielding-elastomeric bearing", J. Vib. Control, 25, 1558-1571. https://doi.org/10.1177/1077546319829535.
  12. Hedayati Dezfuli, F. and Alam, M.S. (2017), "Smart lead rubber bearings equipped with ferrous shape memory alloy wires for seismically isolating highway bridges", J. Earthq. Eng., 22(6), 1042-1067. https://doi.org/10.1080/13632469.2016.1269692.
  13. Iizuka, M. (2000), "A macroscopic model for predicting large-deformation behaviors of laminated rubber bearings", Eng. Struct., 22(4), 323-334. https://doi.org/ 10.1016/S0141-0296(98)00118-7.
  14. Kalpakidis, I.V. and Constantinou, M.C. (2008), "Effects of heating and load history on the behavior of lead-rubber bearings", Technical Report MCEER-08-0027.
  15. Kim, D., Oh, J., Do, J. and Park, J. (2014), "Effects of thermal aging on mechanical properties of laminated lead and natural rubber bearing", Earthq. Struct., 6(2), 127-140. https://doi.org/10.12989/eas.2014.6.2.127.
  16. Kim, J. and Jeong, J. (2016), "Seismic retrofit of asymmetric structures using steel plate slit dampers", J. Constr. Steel Res., 120, 232-244. https://doi.org/10.1016/j.jcsr.2016.02.001.
  17. Kim, J. and Shin, H. (2017), "Seismic loss assessment of a structure retrofitted with slit-friction hybrid dampers", Eng. Struct., 130, 336-350. https://doi.org/10.1016/j.engstruct.2016.10.052.
  18. Lee, C.H., Kim, J., Kim, D.H., Ryu, J. and Ju, Y.K. (2016), "Numerical and experimental analysis of combined behavior of shear-type friction damper and non-uniform strip damper for multi-level seismic protection", Eng. Struct., 114, 75-92. https://doi.org/10.1016/j.engstruct.2016.02.007.
  19. Lee, J. and Kim, J. (2015), "Seismic performance evaluation of moment frames with slit-friction hybrid dampers", Earthq. Struct., 9(6), 1291-1311. https://doi.org/10.12989/eas.2015.9.6.1291.
  20. Lee, J., Kang, H. and Kim, J. (2017), "Seismic performance of steel plate slit-friction hybrid dampers", J. Constr. Steel Res., 136, 128-139. https://doi.org/10.1016/j.jcsr.2017.05.005.
  21. Maleki, S. and Mahjoubi, S. (2013), "Dual-pipe damper", J. Construct. Steel Res., 85, 81-91. https://doi.org/10.1016/j.jcsr.2013.03.004.
  22. Merritt, F. (1996), "Minimum design loads for buildings and other structures: American Society of Civil Engineers Standard 7-95", J. Arch. Eng., 2(2), 80-81. https://doi.org/10.1061/(ASCE)1076-0431(1996)2:2(80)
  23. Oh, S.H., Kim, Y.J. and Ryu, H.S. (2009), "Seismic performance of steel structures with slit dampers", Eng. Struct., 31(9), 1997-2008. https://doi.org/10.1016/j.engstruct.2013.08.011.
  24. Paul, D. (2016), "Effect of lead in elastomeric bearings for structures located in seismic region", Proc. Technol., 25, 146-153. https://doi.org/10.1016/j.protcy.2016.08.091.
  25. Ryan, K.L., Kelly, J.M. and Chopra, A.K. (2005), "Nonlinear model for lead-rubber bearings including axial-load effects", J. Eng. Mech., 131(12), 1270-1278. https://doi.org/10.1061/(ASCE)0733-9399(2005)131:12(1270).
  26. Saadatnia, M., Riahi, H.T. and Izadinia, M. (2019), "Hysteretic behavior of rubber bearing with yielding shear devices", Int. J. Steel Struct., 19(3), 747-759. https://doi.org/10.1007/s13296-018-0159-y.
  27. Saffari, H., Hedayat, A. and Nejad, M.P. (2013), "Post-Northridge connections with slit dampers to enhance strength and ductility", J. Constr. Steel Res., 80, 138-152. https://doi.org/10.1016/j.jcsr.2012.09.023.
  28. Sanchez, J., Masroor, A., Mosqueda, G. and Ryan, K. (2012), "Static and dynamic stability of elastomeric bearings for seismic protection of structures", J. Struct. Eng., 139(7), 1149-1159. https://doi.org/10.1061/(ASCE)ST.541X.0000660.
  29. Sheikhi, J. and Fathi, M. (2019), "Natural rubber bearing incorporated with steel ring damper (NRB-SRD)", Int. J. Steel Struct., 1-12. https://doi.org/10.1007/s13296-019-00267-7.
  30. Tagawa, H., Yamanishi, T., Takaki, A. and Chan, R.W. (2016), "Cyclic behavior of seesaw energy dissipation system with steel slit dampers", J. Constr. Steel Res., 117, 24-34. https://doi.org/10.1016/j.jcsr.2015.09.014.
  31. Talaeitaba, S.B., Pourmasoud, M.M. and Jabbari, M. (2019), "An innovative base isolator with steel rings and a rubber core", Asian J. Civil Eng., 20, 313-325. https://doi.org/10.1007/s42107-018-00107-9.
  32. Tiong, P.L., Adnan, A., Rahman, A. and Mirasa, A.K. (2014), "Seismic base isolation of precast wall system using high damping rubber bearing", Earthq. Struct., 7(6), 1141-1169. https://doi.org/10.12989/eas.2014.7.6.1141.
  33. Yoon, H., Kwahk, I.J. and Kim, Y.J. (2013), "A study on the ultimate performances of elastomeric bearings in Korea", KSCE J. Civil Eng., 17(2), 438-449. https://doi.org/.10.1007/s12205-013-1398-2.
  34. Zhou, T., Wu, Y.F. and Li, A.Q. (2018), "Numerical study on the ultimate behavior of elastomeric bearings under combined compression and shear", KSCE J. Civil Eng., 22(9), 3556-3566. https://doi.org/10.1007/s12205-018-0949-y.

피인용 문헌

  1. Optimized stiffener detailing for shear links in eccentrically braced frames vol.39, pp.1, 2020, https://doi.org/10.12989/scs.2021.39.1.035