DOI QR코드

DOI QR Code

정사각 막냉각홀 내부에서의 열/물질전달 및 유동 특성 (II) - 비대칭 입구조건 효과 -

Heat/Mass Transfer and Flow Characteristics Within a Film Cooling Hole of Square Cross Sections (II) - Effects of Asymmetric Inlet Flow Condition -

  • 발행 : 2002.07.01

초록

An experimental study has been conducted to investigate the heat/mass transfer characteristics within a square film cooling hole with asymmetric inlet now condition. The asymmetric inlet now condition is achieved by making distances between side walls of the secondary now duct and the film cooling hole different; one side wall is $2D_h$ apart from the center of the film cooling hole, while the other side wall is $1.5D_h$ apart from the center of the film cooling hole. The heat/mass transfer experiments for this study have been performed using a naphthalene sublimation method and the now field has been analyzed by numerical calculation using a commercial code. Swirl now is generated at the inlet region and the heat/mass transfer pattem with the asymmetric inlet now condition is changed significantly from that with the symmetric condition. In the exit region, the effect of mainstream on the inside hole now is reduced with the asymmetric condition. The average heat/mass transfer coefficient is higher than that with the symmetric condition due to the swirl now generated by the asymmetric inlet condition.

키워드

참고문헌

  1. Andreopoulos, J., 1982, 'Measurements in a Jet-Pipe Flow Issuing Perpendicularly into a Cross Stream,' J. of Fluids Engineering, Vol. 104, pp. 493-499 https://doi.org/10.1115/1.3241892
  2. Leylek, J. H. and Zerkle, R. D., 1994, 'Discrete-Jet Film Cooling: A Comparison of Computational Results with Experiments,' J. of Turbomachinery, Vol. 116, pp. 358-368 https://doi.org/10.1115/1.2929422
  3. Cho, H. H. and Goldstein, R. J., 1995, 'Heat(Mass) Transfer and Film Cooling Effectiveness with Injection through Discrete Holes: Part I-within Holes and on the Back Surface,' J. of Turbomachinery, Vol. 117, pp. 441-451
  4. Cho, H. H. and Goldstein, R. J., 1995, 'Heat(Mass) Transfer and Film Cooling Effectiveness with Injection through Discrete Holes: Part II -on the Exposed Surface,' J. of Turbomachinery, Vol. 117, pp. 451-460 https://doi.org/10.1115/1.2835681
  5. Muldoon, F. and Acharya, S., 1999, 'Numerical Investigation of the Dynamical Behavior of a Row of Square Jets in Crossflow over a Suface,' ASME Paper No. 99-GT-I27
  6. Lieu, D. N., Findlay, M. J., Gartshore, I. S. and Salcudean, M., 1999, 'Measurements of Heat Transfer Characteristics for Film Cooling Applications,' ASME Paper No. 99-GT-167
  7. Hay, N. and Lampard, D., 1995, 'The Discharge Coefficient of Flared Film Cooling Holes,' ASME Paper No. 95-GT-15
  8. Rhee, D. H., Kim, B. G. and Cho, H. H., 1999, 'Characteristics of Heat/Mass Transfer and Film Cooling Effectiveness Around a Single Film Cooling Hole with Compound Injection Angles,' Transactions of KSME B, Vol. 22, No. 10, pp. 1434-1445
  9. Goldstein, R. J. and Cho, H. H., 1995, 'A Review of Mass Transfer Measurement Using Naphthalene Sublimation,' Experimental Thermal and Fluid Science, Vol. 10, pp. 416-434 https://doi.org/10.1016/0894-1777(94)00071-F
  10. Eckert, E. R. G., 1976, Analogies to Heat Transfer Processes, in Measurements in Heat Transfer, ed. Eckert, E. R. G. and Goldstein, R. J., pp. 397-423, Hemisphere Pub., New York
  11. Kline, S. 1. and McClinetock, F., 1953, 'Describing Uncertainty in Single Sample Experiments,' Mechanical Engineering, Vol. 75, pp. 3-8

피인용 문헌

  1. vol.6, pp.1, 2003, https://doi.org/10.5293/KFMA.2003.6.1.090