This paper is to evaluate practical advantage in using maximizing efficiency control strategy in induction motor drives for electric vehicles. A maximizing efficiency control strategy consist of a flux estimation with direct field oriented controller is proposed and compared with the general constant flux control strategy. The comparison is carried out by simulation.

본 논문에서는 역기전력을 고려한 새로운 토크모델인 CDTP(Commutation Delay Time and Point) 제어기법을 이용하여 실제 역기전력을 고려한 BLDC(Brushless DC)전동기의 토크맥동에 대하여 연구하였다. BLCD 전공기의 상전환(Commutation)시 발생하는 토크맥동에 대하여 기술하였으며 토크맥동의 원인이 되는 역기전력과 전류와의 관계를 고찰하였다. 이를 바탕으로 토크맥동의 개선을 위하여 상전환시점과 상전환기간을 고려한 CDTP 제어기법을 제안하였으며 맥동토크의 저감효과에 대하여 해석하였다. 또한 BLDC 전동기의 실제 역기전력을 고려하기 위하여 Hague의 해석방법에 따른 역기전력의 다양한 형태를 살펴보고, 제안한 CDTP기법을 적용하여 기존 방법을 통한 토크맥동 제어방법과 비교 ${\cdot}$ 검토하였다. 이의 검증을 위하여 MATLAB/Simulink를 이용하여 제안한 방식의 토크맥동 저감방법의 타당성을 살펴보았다.

In a general purpose inverter, a dead-time compensation strategy is very important for reducing torque ripples and acoustic noises of motors. However, in the case of small capacity inverter, the accurate dead-time compensation is hard to be obtained because a removal of the switching noise in a feedback current signal is difficult on condition of low-cost implementation. In this paper, the operation characteristics of the general purpose inverter applied the dead time compensation algorithm using an instantaneous back calculation of the phase angle of the current are presented.

An interior permanent magnet synchronous motor (IPMSM) is receiving increased attention for many industrial applications because of its high torque to inertia ratio, superior power density, and high efficiency. IPMSM is necessary to use the accurate information of the inductance for the precise torque control owing to the reluctance torque. This paper presents two method to measure the each-axis Inductance. The first method uses the peak current that is measured by applying the pulsewise voltage on the each position of IPMSM. The second uses the hysteresis loop of the flux and current measured by applying the positive and negative pulsewise voltage alternately on the each-axis.

In this paper, a new control scheme to use 6-switch inverters for 3-phase switched reluctance motors (SRM) is proposed. Compared with the conventional asymmetric converter topology, it can minimize the entire system size and cost and can increase the efficiency. Therefore, it may have a new topology for SRM to compete the other ac motors, such as induction motors, brushless dc motors, and soon. The validity of the proposed method is verified by simulation, and experimental results.

This paper considers the design and implementation of novel technique of speed estimation and control for IPMSM using learning mechanism-fuzzy neural network(LM-FNN) and artificial neural network (ANN) control. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. This paper is proposed the theoretical analysis as well as the simulation results to verify the effectiveness of the new hybrid Intelligent control

In this paper, we propose fuzzy-neural network controller that combines a fuzzy control and the Neural Networks for high performance control of induction motor drive, Also, this paper is proposed control of maximum torque per ampere of induction motor. This strategy is proposed which is simple in structure and has the honest goal of minimizing the stator current magnitude for given load torque. The performance of the proposed induction motor drive with maximum torque control using fuzzy-neural network controller is verified by simulation at dynamic operation conditions.

This paper describes the design, construction and implementation of matrix converter based on space vector modulation technique. The matrix converter provides sinusoidal input and output wave forms, bidirectional power flow, controllable input power factor and a compact design, compared to the VSI with diode rectification stage at the input. The implemented prototype of matrix converter is built using the exclusive IGBT module and has an input filter, overvoltage protection circuit and commutation means for overcoming practical issues. The good results tested using an induction motor are also presented.

This paper studies particularly applicable method for sensorless Permanent Magnet Brushless DC(PMBLDC) Motor drive system. The waveform of the motor internal voltages (or back emf) contains a fundamental and higher order frequency harmonics. Therefore the third harmonics. component is extracted from the stator phase voltage. The resulting third harmonic signal keeps a constant phase relationship with the rotor flux for any motor speed and load condition. In addition, a simple starting method and a speed estimation approach are also proposed.

In this paper, voltage control strategy for maximum torque operation of stator flux-oriented induction machine drive in the field-weakening region is proposed. In a conventional stator flux-oriented (SFO) induction machine drive system of the maximum torque capability cannot be obtained. The field-weakening method is used to vary the stator-flux reference in proportion to the inverse of the rotor speed. The proposed algorithm, based on the voltage control strategy, ensures the maximum torque operation over the field-weakening region. The proposed algorithm, voltage control strategy for maximum torque operation of capability, which is insensitive to the variation of machine parameters In the field-weakening region. The proposed algorithm is verified by simulation.

We propose an improved sensorless drive method of Switched Reluctance Motors using impressed voltage pulses. Conventional impressed voltage pulse method has a problem of phase delay because of low -pass filter. So In this paper we propose an unproved sensorless driving method based on the impressed voltage pulse using new phase-shift circuit technique that overcomes the phase delay and start-up problem.

In home appliances, electric energy is optimally controlled by using power electronics technology, creating a comfortable environment in terms of energy saving, low sound generation, and reduced time consumption. Usually simplicity and robustness make the three phase induction motor attractive for use in domestic appliance, including washing machines. Two main types of domestic washing machine have evolved. We focus on the front loading machine favored in Europe, which has a horizontal drum axis. The efficiency improvement in home appliances is very important for customers. Induction motor efficiency can be improved by means of loss reduction, which can be realized by motor selection and design, improvement of the waveforms supplied by power Inverter, utilizing a suitable control method. So this paper describes the architecture and feature of washing machine fed induction motor drive under minimizing losses vector control.

In this paper, a study on the controller for high speed PMSM (Permanent Magnet Synchro-nous Motor) is described. PMSM can be driven over 50,000 rpm because it has no brush and commutator structure. It also has less EMI noise and easy cooling structure compare to the other motors. The controller was designed to have a capability to drive 20kw, 42,000rpm high speed motor system. A senseless vector control method was studied based on d-q conversion theory to have a high driving efficiency. The control board was designed using TMS320C33 and the performance was verified by experimental results on driving the inverter and motor system.

The motor research of pre-existing attaches importance about one and three motor of reduce torque ripple and speed control. 3-Phase PMSM Motor, which is generally used, has limited usage in high speed, due to pulsation torque and variable speed. To solve this problem it is necessary to increase invariable, pole number or the number of slots. In this paper 7-Phase PMSM Motor of Steady state analysis of Torque and Output Voltage characteristic.7-Phase modulation method with Space Voltage Vector is studied for ideal operation of controller.

A digital controller of stepping motors is designed for removing mid-range resonance. Rotor oscillation is detected from motor currents and the microprocessor generates frequency modulation taking into account rotor oscillation. ATmega16 is employed and the controller drives stepping motors up to 3000[rpm] at micro stepping.

This paper presents the design and development of web control algorithm of continuous process control system using vector inverter. The Diameter of web is calculated, tension is controlled by PID control and the speed reference of motor is calculated at current diameter. The performance of web control in this paper is verified by experiment.

This paper focuses on the power circuit section of newly developed LSIS inverter for the variable torque application and presents the detailed explanation on the power circuits as well as its application-specific functional performance.

The paper proposes the solar photovoltaic power generation system method for photovoltaic system to solve the power shortage due the sudden power demand. So that supplied electric power to system at appearance during surplus electric power minute and unit moment link driving with common use system is available, digital PLL circuit system voltage through composition and phase of solar photovoltatic power generation system to do synchronization do. Feed forward controller was applied to get fast current response Solar cell that is changed by solar radiation always kept the maximum output when it used Step up chopper. The dynamic character had checked through simulation used Matlab Sumulink and confirmed through an experiment.

The existing DSP for utility interactive photovoltaic generation system control, generally uses floating point process type. Because it is easy to use for number crunching, However it is too late and too expensive. fixed point process DSP, TMS320F2812, has high control speed and is rather inexpensive. This paper presents more efficient method for MPPT control using TMS320F2812.

Utility interactive photovoltaic systems is one of the most premising applications of photovoltaic systems. These systems are employed in applications where utility service is already available. In this case, there is no need for battery storage because utility power may be used to supplement photovoltaic systems when the load exceeds available PV generation. The load receives electricity from both the photovoltaic array and the utility inter-tied. In this paper, Principle and operating characteristic of Utility Interconnected Photovoltaic System is presented. For the purpose of optimal utility Inter-tied photovoltaic system design and installation. It is that demonstrate throughout the installed 3 PV system respectively, 3kW utility interconnected residential system.

Many anti-islanding methods have been developed and tested in pratice. Generally, it seems to be possible to include effective and reliable anti-islanding methods in the PV inverter However, it is difficult to detect islanding phenomenon in the case of multiple systems in the same distribution line. In this paper, the islanding possibility of distributed PV generation system is analyzed and discussed to detect islanding phenomenon.

The arrangement technique of solar cell and module is accomplished quickly with development of power semiconduc-tors. It reached to a practical cost linearly. Photovoltaic power system increases constantly. There are 3kWtracking photovoltaic system and fixed photovoltaic system in Chosun University. This paper compares operating characteristics of the fixed photovoltaic system and the tracking photovoltaic system with shows the efficiency.

한국전력공사에서는 전압원 인버터형 FACTS 기기인 UPFC를 전남 강진군 강진변전소에 설치(2003. 5. 23준공) 운전하였다. 강진 UPFC는 한전과 (주)효성이 공동으로 투자하고, 지멘스와의 기술제휴를 통해 개발하였으며, 40MVA 병렬인버터, 40MVA 직럴인버터로 구성되어 총 80MVA 용량이다. 준공이후 2년여에 걸친 운전으로, 강진UPFC의 고장정지는 현저히 줄었다. 본 논문에서는 강진 UPFC의 주요 이벤트, 고장해소 및 설비의 신뢰성 향상을 위한 대응 조치들에 대해 정리하였다.

An electronic step-down transformer is proposed. Conventional iron cored transformer is heavy and bulky and it has substantial amount of no load loss. On the other hand, electronic transformer can provide negligible no load loss, small size, and light weight. It consists of rectifier and PWM inverter. The output voltage is controlled by duty ratio. To confirm the validity of the proposed transform, simulation and experimental results are presented.

This paper is described the stability and optimization according to each load of induction heating system for using half-bridge high-frequency series resonant inverter. Each metallic package is inserted into the ceramic type vessel with external working coil. This working coil is connected to the resonant inverter. It evaluates performance and stability of this system according to metallic package.

반도체 기술의 발전으로 기존에 전자회로 부품으로 사용되던 LED(Light Emitting Diode)는 차세대 조명용 광원으로 대두되고 있다. LED는 소비전력이 작아 에너지를 절약할 수 있을 뿐만 아니라 수명이 길어 유지보수 비용이 획기적으로 줄어든다. 현재 신호등과 같은 지시용 조명기기를 대체할 광원으로 다양한 시도가 이루어지고 있다. LED는 자체적인 발열은 적지만 주변온도에 민감하게 광도가 변화한다는 단점을 가지고 있다. 높은 온도는 LED의 수명에도 영향을 미쳐 열화를 빨리 가져오게 된다. 따라서 정전류제어를 통해 LED의 전류를 일정하게 하고 온도변화에 영향을 받지 않고 광도를 일정하게 유지하여야 한다. 본 논문에서는 정전류 구동회로에 열화로 인한 LED의 수명의 연장하기 위해 온도변화에 따라 LED의 구동전류와 일정한 광출력을 유지하기 위한 제어회로를 제안하였다. 제안한 제어회로는 시뮬레이션을 통해 타당성을 검증하였다.

전력선통신(PLC : Powerline Communication)을 기존에 이용되고 있는 통신 기술과 접목할 경우 각 통신 방식 간의 단점을 상호 보완할 수 있어 신뢰성, 유연성, 확장성이 우수한 배전계통의 자동화용통신시스템을 구성할 수 있게 된다. 이를 통해 배전계통의 자동화와 안정화를 이룰 수 있어 무정전, 고품질의 전력 공급이 가능해지며, 지상변압기 감시제어시스템, 원격 전력조정시스템, 전력품질 감시시스템 등 향후 도입될 다양한 배전계통의 자동화시스템 구성에 있어 통신망 임대비를 획기적으로 절감할 수 있게 된다. 본 논문에서는 전력선통신을 기반으로 한전 TRS와 위성망, 그리고 케이블, 광통신망을 통합함으로써 신뢰성이 높고 유연성이 뛰어난 복합통신 시스템을 제안하고자 한다.

전력선통신은 다른 통신기술과 달리 표준화 작업이 현재 이루어지지 않고 있으며 타 모뎀과의 호환성이 없다는 단점이 있다. 그러나, 이러한 제약사항들을 극복함으로써 전력선통신의 개발 및 상용화 시기를 앞당길 수 있다. 본 논문에서는 전력선통신의 종합시험장 구축모델 및 시험기준 설계 방안에 관하여 논의하며 전력선통신기기와 관련된 적합성, 성능 및 안정성, 상호운용성에 관한 기준수립 방안에 관하여 고찰하여 전력선통신의 객관적인 성능지표를 마련하고자 한다.

As the developing of industry, the nonlinear equipments as inverter, converter, SMPS(Switching Mode Power Supply) and motor have been increased. But the sensitive electronic loads to the power quality, such as computer's and other electronic equipments, have been spreaded out very fast. Thus, the power quality (PQ) problems and the real time power quality monitoring (PQM) are one of the important issues industry and building area for the intelligent control of the systems. One of them, PQM using PLC(Power Line Communication) have good merits that can send and receive the PQ information without any new network line. This paper presents the PQM hardware and software to monitor the PQ information by using PLC that meets the categories of IEEE Std. 1159.

A new energy-recovery- sustain circuit suitable for a Plasma Display Panel(PDP) application is proposed. The proposed circuit features the low device voltage stresses, essential to design a power efficient and low cost PDP driver circuit. The proposed circuit is demonstrated experimentally for driving a 42 inches plasma display panel.

Proposed Multi-level PDP sustain Driver make use of element which has a low voltage rating instead of suggested method by the existing Webber and it passes through a second phase both rising and falling at sustaining voltage waveform In accordance with the change of timing phase(Tr1, Ti1, Tr2) performance comparison of a electric discharge characteristics in a PDP module has been carried out. At the conclusion of experimentation, the feature is extended by alteration of Ti1 and it has little to do with alteration of Tr1.

A gate driver with Boot-strap chain is proposed to drive Multi-level PDP sustain switches. The proposed gate driver uses only one boot-strap capacitor and one diode per each MOSFETs switch without floating power supply. By adoption of this gate driver circuits, the size, weight and the cost of the drivel board can be reduced.

For transferring the primary power to the secondary one, the high frequency series resonant converter has been widely used for the contactless power supply system. However, the high frequency series resonant converter has the disadvantages such as the low efficiency, the high voltage gain characteristics and deviation of the phase angle in the overall load range. To improve this disadvantage, In this paper, the characteristics of the high efficiency and unit voltage gain as well as in phase are revealed in the proposed three-level LCLC ( Inductor - Capacitor - Inductor -Capacitor)resonant converter. The results are verified on the simulation based on the theoretical analysis and the 4kW experimental prototype.

High accuracy and stability digital controlled power supply for magnet is developed at PLS. This power supply has three sections. The first section is digital controller including DSP&FPGA and precision ADC, the second section consists of IGBT driver and four quad IGBT switch, and the third section is LC output filter section. AC input voltage of power supply is 3-phase 21V, output current is 0 ${\sim}$ 150 A dc. Switching frequency of four quad IGBT switch is 25 kHz. The output current of power supply has very high accuracy of 100 A step resolution at full range and the stability of +/- 1.5 ppm for short term and +/- 5 ppm for long term. This paper describes characteristics of filter and output current performance improvement after LC output filter at four quad digital power supplies.

AC PDP의 구동파형은 Reset 구간에서 명암비를 높이고 화질향상을 위해서 전압파형을 서서히 증가시키고 또 감소시키는데, 이 전압파형의 기울기와 크기가 온도와 더불어서 PDP의 화질과 관련이 있다. 그래서 본 논문에서는 Reset 구간에서 Y 전극에 인가하는 램프파형의 setup 및 setdown 구간에서의 기울기와 -Vy전압을 온도에 따라서 가변함으로써, 주위의 온도가 상온에서 저온이나 고온으로 변화하여도 PDP의 화질이 영향을 받지 않고 최상으로 유지하게 하는 온도 적응형 RESET 파형 발생회로를 제 안하였다.

본 연구는 저전압 교류 전류원으로부터 직류 부하에 에너지를 공급하기 위하여, 새로운 컨버터를 제안한다. 컨버터는 풀브리지 MOSFET 정류기와 플라이백 컨버터의 2단 구조로 구성되어 있으며, LC공진을 이용하여 AC/DC 전력변환을 수행한다. 컨버터 효율 개선을 위하여 컨버터 회로 내의 스위칭 소자는 3상한에서 동작한다. 제안된 컨버터의 동작원리 및 동작모드를 해석하고, 시뮬레이션을 통해 해석결과를 검증하였다.

In this paper, a three phase PWM noninverting Buck-Boost AC-AC converter for WCF applications is presented. The PWM noninverting Buck-Boost AC-AC converter is modelled by using vector DQ transformation whereby the basic DC characteristics equation is analytically obtained. Finally, the PSIM simulation shows the validity of the modelling and analysis.

In this paper, a three phase PWM Watkins-Johnson AC-AC converter for VVCF applications is presented. The PWM Watkins-Johnson AC-AC converter is modelled by using vector DQ transformation whereby the basic DC characteristics equation is analytically obtained. Finally, the PSIM simulation shows the validity of the modelling and analysis.

In this paper, a three phase PWM Zeta AC-AC converter for VVCF applications is presented. The PWM Zeta AC-AC converter is modelled by using vector DQ transformation whereby the basic DC characteristics equation is analytically obtained. Finally, the PSIM simulation shows the validity of the modelling and analysis.

In this paper, the control algorithm of DC source device for inverter starting is proposed and the control method for compensating unbalance system source on operating time in the voltage type PWM converter with driving and regenerative faculty is suggested. The maintaining way of balancing condition for converter of AC source is used the compensating unbalanced status by current control loop. Because it is possible that the unbalanced System control is used to leakage transformer not equaled reactance by each phase in rectifier system, the proposed H/W and control algorithm of rectifier system is contributed to minimize of device and rising efficiency.

본 논문은 ZVS asymmetrical half-bridge converter 에서 무부하시 전력소모 분석과 감소 방안에 대한 연구이다. Asymmetrical half-bridge converter는 영전압 스위칭을 통해 효율 증가가 가능하고, 낮은 EMI 발생의 장점으로 인해 최근 많이 사용되고 있다. 그러나 최근 이슈가 되고 있는 대기전력 소모의 관점에서는 기존의 hard switching converter에 비해 오히려 손실이 증가한다. 이는 공진형 컨버터의 무부하시 동작이 기생전류에 의한 도통손실이 크기 때문이다. 따라서 본 논문에서는 이를 개선 할 수 있는 방법을 제시하고 70W급의 실험용 SMPS의 제작을 통해 제안된 방법의 타당성을 검증한다.

Recently the harmonic generation has declined electricity quality and has bad influence on the electrical installation including OA(Office Automation), FA(Factory Automation), IT(Information Telecommuni-cation) devices and so on. The study of harmonics be greatly interested in diagnosis accident with harmonics was not merely guesswork but clarify the cause by experimental data at these days. Therefore, it is necessary development of AC power source for correct experiment with reliable data. In this paper, we realized the AC power source that can produce and compose harmonics for analysis of accident with harmonics.

The author present a modified multi-loop algorithm Including feedforward for controlling a 55kW stepdown chopper in the power supply of Maglev The gains of the control algorithm were selected based on pole locations formulated from a prototype Bessel transfer function model. The design incorporate tradeoffs in DC-to-DC converter hard-ware para-meters and pole locations. This perturvation is derived by subtracting the desired output voltage from the actual output voltage. The proportional and integral action stabilizes the system and minimizes output voltage error. In order to verify the validity of the proposed multi-loop controller, simulation study was tried using Matlab simulink.

본 논문에서는 30W급 스위칭형 직류전원장치 (Switching Mode Power Supply : SMPS)에 준공진형 프라이 백 스위칭 레귤레이터(quasi-resonant flyback switching regulator)를 적용하여 방사노이즈(radiation-noise)를 억제한 사례에 대하여 설명하고 있다. 기존의 PI사(社)의 TOP IC 시리즈$^{[1]}$와 같이 보편적으로 사용되고 있는 일명, 하드 스위칭(hard-switching)형 레귤레이터를 사용할 경우, 고속 스위칭시에 스위칭 손실(switching loss)과 스위칭 노이즈(switching noise)가 발생한다. 이로 인하여 SMPS의 발열에 따른 효율저화와 방사 노이즈에 의한 전파방해 등이 문제점이 된다. 본 논문에서는 일본의 Sanken사(社)에서 개발/시판중인 준공진형 스위칭 레귤레이터인 STR-F6000 IC 시리즈$^{[2]}$를 이용하여 프라이백 SMPS를 구성하여 방사노이즈를 저감하였다.

SMPS의 손실에는 switching loss, conduction loss, core loss가 있다. 최근 SMPS에서는 switching loss를 줄여 효율을 높이고자 반도체 스위치 2개를 사용하는 공진형 구조가 증가하고 있다하지만 공진형 구조는 반도체 스위치에서 소비되는 conduction loss로 의해 기존의 컨버터에 비해 무부하시 전력 소모가 크다. 그러나 최근 시장은 무부하시 소비되는 대기전력의 규제가 이슈가 되고 있다. 본 논문에서는 active clamped flyback converter에서 무부하시 반도체 스위치의 conduction loss의 감소를 위해 Clamp 회로의 보조 스위치는 동작시키지 않고, flyback converter로만 동작하도록 설계하여 무부하시에는 기존의 flyback converter의 동작과 같이 도통 손실이 급속히 줄도록 하였다. 또한 스위칭 손실을 줄이기 위해 주 스위치의 동작 주파수를 감소시켜 SMPS의 무부하시의 소모를 감소시켰다. 70W급 SMPS의 제작과 실험을 통해 위의 방법을 증명하고자 한다.

This paper describes the transmission method of an information using communication networks between RTU(Remote Terminal Unit) and PCU(Protection and Control System) of the DC switchgear for Light Railway Vehicle. Also the test result carried out in the laboratory was represented. In this test, transmission signal waveform, polling time, response time and request/response frame between RTU and PCU were measured. The field test including the measurements of analog signal and status of the digital logic operation of PCU was conducted in Gyeongsan Test Track.

According as the industry develops recently, the import and export freight amount is increasing sharply, but physical distribution processing equipment ability had achieved conveyance, surge and setup of physical distribution by human's labor ability. But, inefficiency is indicated in operation of harbor and bay warehouse or physical distribution storage equipment because is ceilinged the processing physical distribution amount and the efficiency in physical distribution processing by these labor ability. Treatise that meet on the request proposes soldier warehouse physical distribution processing system that apply Vision System.

Recently, power supply-demand instability due to the dramatic increase in power usage suchas air-conditioning load at summertime has brought forecasts of decrease in power supply capability. Therefore improving the load factor through systematic load management, in other words, Direct Load Control became necessary. Direct Load Control(DLC) system is kind of a load management program for stabilization of electric power supply-demand. It's purpose is limiting the demand of the demand side selected at peak load or other time periods. The paper presented a Design of Direct Load Controller for control the amount of power demand in demand side. The proposed Controller is cheaper and has ability of storing more power data than pre-existing device.

본 논문에서는 CCD 카메라의 시각정보 이미지를 이용한 Machine Vision System을 개발하여 산업용 로봇에 적용하고 이를 통해 이동물체에 대한각종 조작 및 자동화 작업을 수행하는 지능형 산업용 로봇을 위한 실시간 비전 트래킹 시스템을 연구하였다. 비전 트래킹 시스템에서 물체의 위치 계산에 대한 정밀도와 함께 빠른 처리속도를 요구하므로 로봇제어기와는 별개의 Embadded 시스템으로 비전 제어기를 구성하고 로봇제어기와의 Serial 통신을 통하여 트래킹 시스템을 구현하였다.

The computation of design parameters and the electromagnetic analysis of 0.5 Mw- class Induction furnace with 3-dimensional modeling are Introduced by using FEM techniques, And model of flux distribution and eddy current distribution induced in induction furnace are analyzed and presented. It is more necessary that for melting industry depending on metal material field, the design technique of induction furnace is quite urgent at exchanging introduction of technology between metal material and electrical energy conversion by power electronics field.

본 논문은 회전형 대용량의 진단 X-선 발생장치를 모노 블록 형태로 설계, 병원의 모바일 진단장치나, 산업용 X-선 장치로의 적용이 가능한 16kw급 X-선 발생장치에 관한 연구이다. 본 장치는 X-선 발생을 위한 고전압 발생부에 회전형 Anode 형의 X-선관을 사용하였고, X-선관의 로터를 구동할 수 있는 로터 구동회로를 추가 하였다. 고주파 고전압용 인버터에는 IGBT(600/300A)를 100kHz로 고주파 스위칭 함으로서 고전압 변압기를 비롯한 고전압 발생부의 크기와 무게를 최소화하였다. 또한, 기존의 16kw급 대용량 진단 X-선 발생장치를 X-선관과 고전압부를 일체화한 모노블록 형태로 설계, 제작하여 부하변동에 따른 X-선 관전압과 관전류의 동작특성을 실험을 통하여 입증하였다.

전력연구원은 고속의 DSP TMS320C33를 이용하여 실시간 정지형 계통연계 발전기 시뮬레이터를 개발하였다. 특히 소프트웨어로는 MicroC-OS를 이용하였으며 제어주기는 2500Hz이상으로 설계되었다. 실제 발전소에서 상업 운전되고 있는 여자시스템을 대상으로 하여 시뮬레이터 시험을 완료하였다.

대용량 동기 발전 전동기 운전의 기동용 시스템으로 주로 사이리스터를 이용한 정지형 주파수 변환(SFC : Static Frequency Converter) 시스템이 사용되고 있다. 본 논문에서는 SFC시스템의 기동부터 회생까지 파형을 5KVA급 동기 전용 발전기 모의실험을 통하여 제시하고 330MVA급 양수 발전소의 실측 파형을 분석하여 알고리즘을 도출하였으며 또한 시뮬레이터 파형과 실제 파형을 비교해 함으로써 양수발전소의 제어 시스템의 운전특성을 유추 및 분석하였다.

Internal battery ohmic measurements have been a hot topic amongst battery users and battery manufacturers. As a battery deteriorates and loses its capacity, the internal resistance of the battery increases. Everyone seems to agree that measuring the internal parameters of a cell can be very useful in determining a battery's state of health. In this paper experiences show that if a cell's resistance increases by more than25% above its baseline value(known good resistance of new 100% capacity cell), the cell will no loger be able to deliver 80% or more of the rated capacity.

Malfunction of Klippon relay in Cheju-Haenam HVDC system has been caused by the inflow of high voltage arc. In this paper, we have studied on the theoretical examination and data analysis of Klippon relay, and the countermeasures against the problems were suggested according to their causes. Grounding problem in Klippon relay is removed by one-point earth connection and by modification of grounding circuit. The effects of over current surge was removed by attaching blocking diodes by series In Klippon relay to remove surge input in Klippon relay's mercury contact. The problem of Induced overvoltage by 86re1ay excitation coil, was removed by attaching Free-wheeling diode in parallel with the excitation coil of Lock-out relay.

In this paper deals with the frequency control of the HVDC scheme linking Haenam to Cheju Island. The primary aim of the study is to develop and evaluate a new frequency control that can be employed without having to utilize the existing Synchronous Compensators(Gas Turbines). Study cases are completed involving synchronous compensators trip and load tripping events and study plots presented. It is demonstrated that the existing frequency measurement can be replaced by one derived from the AC network alone, incorporated into a new frequency control algorithm and gives good frequency control and dynamic performance.

PWM(Pulse Width Modulation) 컨버터에서 공급 전압의 품질은 교류 입력전류 및 직류 출력전압의 품질에 큰 영향을 미친다. 공급전압이 불평형 또는 고조파가 포함된 경우에는 평형 전원전압의 경우보다 입력 전류의고조파 및 역률 특성이 저하된다. 또한 컨버터 입력 측의 사용된 인덕턴스의 용량에 따라 입력전류의 고조파 및 역률 특성이 달라진다. 본 논문에서는 입력측 인덕턴스 값의 변화에 따른 단상 및 삼상 PWM 컨버터의 입력전류 고조파와 역률 관계를 해석하였는데, 특히 입력전압에 고조파를 포함한 경우와 불평형인 상태까지 확장하여 성능을 평가하였다. 이러한 결과를 통해 입력 인덕턴스 설계 값을 선정하는데 기준을 제시하였다.

The human beings have Increased concern about Energy saving and alternative energy. The power demand has increased the growth of industry and the improvement of life We have to explore alternate energy sources and utilize effectively domestic resources. The lighting equipments developed Energy saving by using an electric ballast. The load installation should be promoted to rational power management, according to the network, intelligent, and high-function. Therefore, this paper has studied the method of energy saving and consulting.

The recent growth in the use of impactive and nonlinear loads, electronic devices sensitive to power quality has caused many power quality problems. Dynamic voltage restorers(DVR) are known as the best effective and economic means to compensate for power quality problems(especially, voltage sag and swell). In this paper, we addresses the detecting algorithms of an voltage sag and phase for operating DVR. Experimental results are included to illustrate the efficacy of the proposed algorithm.

This paper proposes an implementation of a line- voltage sensorless three-phase active power filter. The line synchronization for an active power filter does not require any additional hardware. It can be properly operated under various line-voltage variation. Current compensation is done in the time domain allowing fast time response. All control functions are implemented in software using a single-chip microcontroller, thus simplifying the control circuit. It is shown via experimental results that the proposed controller gives good performance for the line-voltage sensorless active power filter.

Development of nonlinear loads and compensation instruments make PQ(Power Quality) problem into important issue. Few studies by signal processing and pattern classification as NN(Neural Network), Wavelet Transform, and Fuzzy present feature extraction. A lot of Input features make not always good result and they are difficult to make realtime system. Thus, The dimentionality reduction is indispensable process. PCA(Principal Component Analysis) reduces high-dimensional input features onto a lower-dimensional subspace effectively. It will be useful to apply to realtime system and NN.

This paper proposed the new harmonic detection system for the source current with the large frequency variation. The harmonic detection system is designed of the analog circuit and is composed of a low pass filter, a DC-level converter using the PLL, the Voltage controlled GIC.

The 2.5 GeV linac of the Pohang Light Source(PLS) is planed to be converted to a XFEL. The PAL XFEL requires a new 1.2-GeV linac that will be combined to the existing linac to increase a beam energy upto 3.7 GeV. The RF stability of 0.02 % is required for both RF phase and amplitude to get the XFEL output. This stability is mainly determined by a low level RF drive system and klystron-modulators. The stability level of the modulator has to be improved 10 times better to meet the pulse stability of 0.02 %. The regulation methods such as traditional de-Qing and precision inverter charging technology are reviewed to find out suitable upgrade scheme of the modulators.

A new 3-phase line-interactive UPS(Uninterruptible Power Supply) system with parallel-series active power-line conditioning capability using AC line reactor and two four-leg PWM VSCs(Voltage Source Converters) was introduced recently, In this paper, the strategy of voltage control in suggested UPS system is explained. The objective of proposed voltage controllers in parallel(shunt) and series PWM VSC is to guarantee satisfactory characteristics in steady state and transient state.

The development of control related applications requires knowledge of different subject matters like mechanical components, control equipment and physics. To understand the behavior of these heterogeneous applications is not easy especially the students who begin to study the electronic engineering.

This paper describes a design of several ship's emergency lighting system(SELS) that power factor is improved and power is controlled extensively, and techniques to control and monitor this system in remote distance by PC serial communication. The remote monitoring control system is composed of emergency power supply system (EPSS), half bridge(HB)inverter, fluorescent lamp(FL), microprocessor, multi communication interface. EPSS checks the voltage of the emergency backup battery in real time. In case that the voltage of 13[V] or less has been detected for 5[msec] or longer for 3 times in a row, charger circuit is connected for battery charging. Experimental works using proposed system confirm that speedy and stable power to be supplied when main power source cut-off, compared with conventional analog type, and input power up to 35.0[%] by adjusting of pulse frequency of the HB inverter.

RPA(Remelt Power Analysis)and RC(Remote Control) System have been researched from former several decade for a various power rate system a efficent power service and rising of personal expenses, etc. But the existing RPA and RC System have disadventage which are complex and high cost to install an individual communication network of electricity company This paper proposed a new type of RPA and RC System using PLC with Internet. and made components for proposal system so we made the PLC modem, the digital watt-hour meter with a build in PLC modem and the softwere on server computer for establishing the proposal system. The bit rate of the proposed system is about 4800bps.

In this paper, a novel motor control method is proposed to improve the performance of sensorless drive of BLDC motors. The unknown input (back-EMF) is modelled as the additional state of system in this paper. Taking into account the disturbance adopted by the back-EMF, the observer can be obtained by the augmented system equation. An algorithm to detect the back-EMF of the BLDC motor using the state observer is constructed. As a result, the novel sensorless drive of BLDC motors that can strictly estimate rotor position and speed is proposed.

In this paper, a novel sensorless brushless DC (BLDC) motor drive method using the fuzzy back-EMF observer is proposed to improve the performance of conventional sensorless drive methods. Most existing back-EMF sensing methods need additional circuit and have a low performance intransient state or low speed range. Therefore, this paper proposes the fuzzy back-EMF observer and an algorithm using this observer to estimate a speed and a position of the rotor. The robustness of the proposed algorithm is proved through the simulation compared with other sensorless drive methods.

본 논문에서는 새로운 회전자 위치 오차 예측 알고리즘(RPEPA)를 이용한 BLDC 전동기의 센서리스 제어 방법을 제안한다. 회전자 위치 정보는 3상 단자 전압으로부터 간접적인 Back-EMF 검출에 의해 추정되고, 저역통과 필터는 스위칭 노이즈 제거를 위해 사용된다. 제안한 방법은 저속 영역에서 기존 방법들 보다 향상된 성능을 갖고 있다. 필터에 의해 발생되는 위상 오차는 새로운 RPEPA에 의해 실시간 보상되어 정확한 전환시점을 결정한다. RPEPA를 이용한 센서리스 방법은 넓은 속도범위와 전동기의 효율을 개선시킨다. 제안한 방법은 실험을 통하여 타당성과 효율성을 검증한다.

교류전동기의 벡터제어 구동 시스템에서 상전류 측정 오차는 토크 및 속도 제어 성능에 직접적인 영향을 주는 요소로서, 맥동 없는 토크 및 속도 제어를 위해서는 상전류의 정확한 측정이 필요하다. 상전류 측정 오차는 오프셋(Offset) 변동에 의한 오차와 스케일(Scale) 차이에 의한 오차로 분류할 수 있으며, 각각의 오차 성분은 고정자 전기 주파수의 1배 및 2배에 해당하는 토크 맥동을 야기 한다. 본 논문에서는 교류전동기 벡터제어 구동 시스템에서 상전류 측정 오차에 의한 토크 맥동을 저감시킬 수 있는 새로운 알고리즘을 제시하며, 시뮬레이션 및 실험을 통해 제안된 방식의 타당성을 입증한다.

This paper present a new method for world wide network motor controlled system. It use disturbance observer to present high precision position control algorithm to disturbance change, and to apply this to induction motors. It shows that proposed algorithm is strong in induction motor precision control for disturbance change. This system with disturbance observer used deadbeat control, which have high benefit, is good for quick disturbance compensation. To show these effectiveness the whole process is simulated by simulink, and also experimented by DSP6416 with TCP-IP network board.

In this paper, an instantaneous speed observer with a reduced order is proposed to implement an indirect control for an motor with excellent dynamic stability and performance in a very low speed region. The proposed observer can estimate the instantaneous speed in very low speed region and simplify the system configuration by adopting a least order load torque-inertia observer to estimate the load torque and the rotor speed. Simulation are carried out to illustrate the performance of the proposed estimator at very low speed.

This paper describes the ultra precise position estimation of a servomotor using sinusoidal encoder based on Arcsine Interpolation Method. The amplitude and offset errors of the sinusoidal encoder output signals are effectively compensated and on-line tuned by utilizing a low cost programmable differential amp without any special expensive equipments. To theoretically evaluate the practical resolution of this system, the relationship between the amplitude of A/D converter input signal errors and the anticipated resolution is briefly dealt with. The performance of the proposed method is verified by the experiments, by comparing it with position and speed control characteristics of the servomotor driving system using a digital incremental 50,000ppr encoder.

The linear hybrid stepping motors (LHSM) has been widely used due to its simple structure and low cost control. Despite of its attractive features, the conventional LHSM has the multiples of 4th times harmonic reluctance force from excitation current and cogging force from space harmonic of permeance. This paper propose a new LHSM, which the mechanical and electrical phase difference are 45$^{\circ}$. The proposed motor shows a unique ability to deliver low detent force and we propose a closed-loop control scheme to attack the ripple force for high performance applications. An analytical and experimental comparison between conventional and proposed LHSM is evaluated to confirm the effectiveness of the proposed modeling and control scheme.

본 논문에서는 영구자석 동기전동기의 운전중 간섭성분을 형성하는 고정자 인덕턴스가 변화할 경우 d축 전류의 오차로부터 고정자 인덕턴스의 변화량을 보상할 수 있는 보상기를 제안하였다. 그리고 이러한 보상기를 기존의 DDC(Dynamic Decoupling g Control)에 적용하여, 고정자 인덕턴스의 변화에 대한 강인성이 향상된 비간섭 전류제어기를 설계하였다.

This paper suggests a new type of 4-switch inverter for switched reluctance motor drives. 4-switch Inverter topology is studied to provide possibility for the realization of cost of 3-phase SRM drive system. We used Y-connection and two-phase exciting method. For effective utilization of the developed system, a direct current controlled PWM scheme is designed and implemented to produce the desired dynamic. We solve to balance the neutral point of Y-connection by the direct current controlled PWM and examine the performance of proposed system. With the algorithm and developed control scheme, is expected that the proposed system can be widely used in commercial applications with a reduced system cost.

This paper presents a study on a current control of a PM synchronous motor which is fed by two-level voltage source inverter in the high modulation index area. In order to increase dynamic response and extend speed limit caused by voltage limit, overmodulation method is generally used. The current control in overmodulation have voltage limit. So larger voltage command than voltage limit should be diminished. In this paper, the problem conventional normalization method is analyzed and New normalization method in overmodulation region is proposed.

This paper describes a design of a vector control module for AC motor using high density FPGA. In the proposed vector controller, the vector control blocks including inverse dq transform, space vector PWM and quadrature encoder pulse module are implemented in a FPGA using a VHDL. The simulation results are provided to show the validity of the proposed vector control module.

Three different current-mode control schemes, peak current-mode control, charge control, and average current-mode control, are investigated for applications to asymmetrical half-bridge dc-to-dc converters. The principles, implementation, and performance of the three control schemes are compared in an attempt to identify the irrespective merits and limitations. Design examples for feedback compensations are given for the three control schemes. A 50 W experimental asymmetrical half-bridge dc-to-dc converter was used to experimentally verify the theoretical results of the paper.

본 논문에서는 하이브리드 자동차용 보조전원 공급이 목적인 DC-DC Converter에 대하여 기술하였다. DC-DC Converter는 차량 내의 헤드램프, 오디오, 각종 ECU등 전기/전자 부하에 전력을 공급하며 또한 12V 보조 배터리를 충전하는데 사용된다. 고주파 동작 조건하에서 유기되는 전자파 노이즈와 스위칭 손실을 저감하기 위하여 컨버터 토폴로지로 위상천이 영전압 풀브리지 방식을 적용하였으며 제어기의 용이한 보상 및 안정된 시스템 응답 특성을 위하여 슬로프 보상이 포함된 전류 모드 제어방식을 사용하였다 정전압/정전류 충전 제어 방식은 전기부하에 안정적인 전원공급과 보조 배터리의 안정적인충전을 보장한다. 초기의 회로 파라메타 설정 및 하드웨어 디버깅을 위하여 시뮬레이션 툴로 PSIM 6.0을 사용하였으며. DC-DC Converter에서 스위칭 소자의 발열문제는 Thermo Tracer 장비를 사용하여 개선하였다.

A new synchronous switch controlled transient current build-up zero voltage switching (TCB-ZVS) forward converter is proposed. The proposed converter is suitable for the low-voltage and high-current applications. The features of the proposed converter are low conduction loss of magnetizing current, no additional circuit for the ZVS operation, high efficiency, high power density and low EMI noise throughout all load conditions.

본 논문은 입력 필터 상호 작용 (Interacton)의 일반적인 해석 방법으로 입력 필터단이 연결된 전류 제어 DC-DC 변환기의 동특성을 해석한다. 또한 입력 필터단의 강한 영향을 받는 상태의 전류 제어 강압형 변환기의 새로운 소신호 해석 결과를 제시한다. 이론적 해석은 컴퓨터 시뮬레이션 결과 및 제작된 실험용 PWM DC-DC 변환기로 검증하였다.

본 논문은 PWM DC-DC 변환기의 입력 임피던스를 Middlebrook의 EET (Extra Element Theorem)를 사용하여 해석할 수 있는 방법을 제시하고, 이를 이용하여 실제로 전압 제어, 전류 제어 승압형 변환기에 대한 입력 임피던스를 해석하였다. 유도된 수식은 간략화, 근사화를 통하여 보드 선도 (Bode plot)화 하였고, 입력 임피던스 특성 및 전류 루프, 피드백/피드포워드 루프, 전압루프의 영향을 해석하였다. 또한 이론적 해석은 컴퓨터시뮬레이션 결과 및 실제 제작된 PWM DC-DC 변환기의 실험 결과로 비교, 검증하였다.

본 논문에서는 입력 필터의 영향을 받는 스위칭 전력변환기의 이론적인 해석 과정을 나타내었다. Middle-brook의 extra element theorem을 이용하여 이론적으로 입력 필터 상호 작용을 해석하였으며, 컴퓨터 시뮬레이션을 통해 확인하였다. 또한 전압 제어 및 전류 제어방식 승압형 변환기를 제작하여 이를 검증하였다.

Recently, due to the launching of digital broadcasting service, a demand of PDP TV with large screen size is sharply rising. PDP power module is mainly divided into power factor correction (PFC) stage and sustaining power stage. Especially, sustaining power module has pulsating load characteristics. So, the hard switching at light load condition causes low efficiency and thermal problem. Therefore, a new power conversion circuit for sustaining power module of 60' PDP is proposed whose ZVS is obtained by additional ZVS tank. This paper presents properties of the proposed converter through mode analysis, numerical analysis. And a 900w prototype for sustaining power module of 60' PDP is produced to verify the analytic results. As an experimental results, ZVS is achieved from full load to 10% load variation and more than 92% of high efficiency is obtained at 10% load condition.

Three control strategies that can be applied to a three-phase AC-DC converter under unbalanced input voltage condition are discussed. Analytic solutions are given on the a-b-c frame, and are very simple, direct and Intuitive. All of the strategies guarantee sinusoidal input currents. All the control functions, including decoupled current control and PWM, are implemented on the a-b-c frame. Accordingly, the controller is very simple and robust. The proposal is verified by simulation and experiments on a prototype operating at 15 kHz

Conventional phase shift full bridge (PSFB) converter has serious voltage oscillation problem across the secondary rectifier diodes, which would require the dissipate snubber circuit, thus degrades the overall efficiency. To overcome this problem, a new voltage oscillation reduction technique (VORT) which effectively reduce the voltage oscillation of the secondary rectifier diodes for phase shift 1011 bridge converter is proposed. Therefore, no dissipate snubber for rectifier diodes is needed. In addition, since it has wide zero voltage switching (ZVS) range, high efficiency can be achieved. Operational principle, analysis of voltage oscillation, and design consideration are presented compare with that of the conventional PSFB converter. To confirm the validity of the proposed VORT, experimental results from a 420W, 385Vdc/210Vdc prototype are presented.

In this paper results of the experiment which used LLC resonant half bridge DC-DC converter to a portable electrical equipment. LLC resonance Half Bridge DC-DC converter which was used in this experiment improved an efficiency because it reduced switching, conduction losses and with synchronous rectifier. As a result of the experiment, this proposed converter could verified an increase of 2% to the efficiency more than diode rectifier.

A new zero voltage switching (ZVS) 2-transformer boost converter is proposed in this paper. The proposed converter has the advantage that the magnetizing inductor of the transformer acts for the boost inductor without additional inductor. Moreover, ZVS of main switches and auxiliary switches can be achieved, and the switch turn-off surge problem of conventional isolated boost converter is effectively solved. The operational principle, DC voltage gain, and ZVS characteristics are analyzed. To confirm the validity of the proposed converter, simulation results with 200w, 24Vdc/200Vdc specification are presented.

This paper presents a novel current driving method for the synchronous rectifier (SR) in a Flyback topology. The proposed current driven synchronous rectifier features low Power loss, good performance and the gate voltage of FET in the synchronous rectifier is easily controlled by zener voltage. The proposed SR driving method is implemented in a 200W Flyback converter with 400Vdc input and achieved excellent performance at full load.

The flying capacitor voltage control of the flying capacitor multi-level inverter (FCMLI) is very important for safe operation. The voltage unbalancing of flying capacitors caused serious problems in safety and reliability of system. In the FCMLI, balancing problem of the flying capacitor has its applications limited. The voltage unbalance is occurred by the difference of each capacitors charging and discharging time applied to FCMLI. This paper investigates and analyzes multi-carrier PWM methods to solve capacitor voltage balancing problem. The Phase-Shift PWM (PSPWM) method that is commonly used, The Modified Carrier-Redistribution PWM (MCRPWM) method and The Saw-Tooth-Rotation PWM (STRPWM) method are discussed and compared with respect to switching state, balancing voltage of capacitors and output waveform. These three PWM methods are analyzed by using a flying capacitor three-level inverter and provided result through simulation. Finally, the harmonics about the output voltages of their methods are compared using the harmonic distortion factor (HDF).

본 논문에서는 입력단 역률제어 및 고조파 전류억제를 위해 PWM 컨버터를 이용하는 3상 UPS에서 직류측을 공통으로 연결하여 하나의 배터리 유닛만으로 병렬 UPS운전이 가능한 공통 배터리 운전에 대해 기술한다. 직류측을 공통으로 이용함으로써 PWM 컨버터 간에 흐를 수 있는 순환전류를 없애기 위한 제어기를 제안하고 실험을 통해 제안한 방법의 타당성을 검토한다.

본 연구는 순수 국내기술로 개발된 국산화 전동차 광주도시철도 1호선의 추진제어 장치의 본선시운전에 관한 것으로, 외국기술에 의존해온 추진 제어장치를 국내기술로 설계하고 본선시운전을 통하여 추진제어장치의 신뢰성 및 안정성에 관하여 실험을 실시하였다. 그리고 추진제어 장치에 적용한 알고리즘은 필터 사이즈를 감소하기위하여 기존의 패턴에 의한 PWM방식을 사용치 않고, 출력전류의 고조파 리플이 적은 저주파 동기 공간벡터 PWM 알고리즘을 제안하고, 가선전압의 변동에 강인한 댐핑 제어 및 과전압 제한 제어 알고리즘을 제시하고, 제안된 알고리즘은 본선시운전을 통하여 타당함을 확인하였다.

본 연구의 내용은 전력 반도체의 파워 싸이클링 수명을 시스템의 요구 수명에 맞추어 최적화하는 것이다. 파워 싸이클링 수명은 전력 반도체의 졍션과 방열판 간의 온도 상승에 의한 수명 싸이클으로 졍션과 방열판간의 온도 변화가 클수록 수명은 단축된다. 따라서, 전력 반도체의 졍션과 케이스간의 온도 상승을 최소화하기위하여 시스템에 최적화된 구동 방식을 찾는다. 정격 속도에 도달하는 가속 시간의 제한이 필요 없는 시스템의 경우는 가속도 및 가가속도를 낮추는 방법을 사용하였다. 정격속도에 도달하는 가속 시간이 제한되는 경우는 가속 시스위칭 주파수를 시스템이 허용하는 한 낮추는 방법을 사용하였다. 본 논문에서는 엘리베이터를 모델로 사용하여 전력 반도체의 손실 및 수명을 최적화 하였다.

본 논문은 대용량 진력변환장치인 멀티-레벨 인버터 시스템에서 출력 전압가변이 손쉬운 HBML(H-Bridge Multi-Level) 인버터의 Master와 Cell 제어기 구성에 관한 것이다. HBML 인버터는 각각의 단위 Cell을 저압에서 사용하는 인버터로 구성하면, 구조적으로 풀-브릿지(Full-Bridge) 인버터를 캐스케이드 방식으로 연결하여 고압출력을 얻을 수 있는 토폴로지이다. 시스템에서 Master와 Cell의 제어 처리를 한곳에 집중하지 않는 분산 제어 방식을 적용하여 통신 Data를 최적화하도록 구성하고, 이를 바탕으로 두 제어기를 고성능 원-칩(One-Chip) DSP로만 설계하였다. 모든 외부 모듈을 내장한 CPU로 제어기가 구성될 경우, 외부 노이즈에 강하며, 추가되는 하드웨어 결선을 최소화할 수 있다. 본 논문에서는 HBML 인버터 출력 생성 시 반드시 요구되는 출력 PWM 동기 및 위상전이(Phase Shift)를 각 제어기 자체에 내장된 모듈만을 이용해서 구현하였다.

본 논문은 멀티-레벨 H-bridge 인버터에서 입력전압 변동에 따른 AVR(Auto Voltage Regulation)기능을 적용 그 타당성을 제안하였다. 기존의 범용 인버터에서 (V/F)로 구동되는 전동기 시스템에 있어서 인버터에 공급되는 입력 전압은 출력 주파수에 따라 출력 전압 비율을 일정하게 하고 기동에 필요한 전압을 더하여 출력하는 방식이다. 집중 제어 방식의 멀티-레벨 H-bridge 인버터에서는 Cell의 DC-Link 전압을 Master에서 받아들여서 각각의 Cell에 기준 전압값을 지령하게 된다. 그러므로 입력 전압 변동에 따른 DC-Link 전압의 변동이 발생하게 되면 상전압 Unbalance 가 발생하게 되어 부하가 원하는 출력 전압을 낼 수가 없게 된다. 또한 각각의 Cell을 제어하는 Master 제어기가 가지고 있는 문제점을 보완하여 각각의 Cell 제어기 스스로가 AVR을 수행하는 좀더 나은 방법을 제안하였다.

This paper describes the application of newly developed conducted EMI reduction technique of SVPWM in induction motor drive. The newly developed common mode voltage reduction SVPWM technique doesn't any zero-voltage vector states for inverter control. Hence it can restrict the common mode voltage better than conventional PWM technique. The proposed technique is verified through simulation and experimental results. And by applying vector-controled system, the proposed technique have superior ability of reducing EMI and equal control performance comparing conventional SVPWM technique.

EEFLs are mostly driven by sinusoidal wave driving method although EEFLs (External Electrode Fluorescent Lamps) are driven by both sinusoidal wave and square wave. The sinusoidal driving method reduces the cost and allows more power efficiency since this driving method can reduce the voltage stress of EEFL inverter switches and achieve the soft switching of the switches. And a transformer should be used in the inverter since the high voltage should be applied to the both ends of EEFL to turn on the lamp. However, the power loss mainly occurs at the transformer in the sinusoidal wave driving method. In order to remove the transformer which makes the power loss, a new method is presented. In this paper, the square wave is applied directly to the both ends of EEFL by a proposed two-stage inverter. Moreover, the luminance and power efficiency will be compared between the common sinusoidal wave driving method and square wave driving method.

Distributed generation (DG) systems fall in islanding operation when they still in operation even when the main grid is out of electric power Islanding operation is further classified into intentional islanding and unintentional islanding operations. In intentional islanding operation, the DG backs up critical loads while it separates from the main grid on islanding detection. Intentional islanding operation increases utilization of the DG system during the islanding operation. This paper proposes reasonal inverter topology and its control algorithm for seamless transfer of DG systems in intentional islanding operation.

In this paper, supposed to solve these problem to PID parameters controller algorithm using ANN. In the proposed algorithm, the parameters of the controller were adjusted to reduce by on-line system the error of the speed of IM. In this process, EBPANN was constituted to an output error value of an IM and conspired an input and output. The performance of the self-tuning controller is compared with that of the PID controller tuned by conventional method (Ziehler-Nichols). The effectiveness of the proposed control method is verified thought the Matlab Simulink and experimental results.

This paper presents a PM type BLDC(Brushless DC) Motor servo drive system using high performance DSP TMS320F2812. The DSP controller with 150MIPS enables an enhanced real time implementation and increased efficiency and high performance for motor drive. The suggested drive system consists of PI action for the constant speed control and PID action for the current control with only 3 Halls, no encoders. The developed servo drive control system shows a good response speed characteristics at high speed up to 10000 [rpm].

A sliding mode controller for the grid-connected photovoltaic system has been presented. This controller is constructed from the time-varying sliding surface In order to control the sinusoidal inductor current and solar array power simultaneously. The proposed controller can achieve the tight regulation of current and power under the parameter variation environment.

In this paper a power conditioning system suitable for the fuel cell powered off-road vehicle is proposed. The proposed system employs a Proton Exchange Membrane Fuel Cell stack combined with boost converter, a super capacitor module combined with hi-directional buck-boost converter, a 4-quadrant DC chopper and a permanent magnet DC motor. The momentary overload condition occurring during the motor starting is handled by the energy stored in the supercapacitor module. Also, the regenerative energy can be stored in the supercapacitor module by operating the system in either buck or boost mode. This capability gives the system designer the higher flexibility in designing the system and assures the lower cost of the system. The validity and feasibility of the proposed system is proven by the computer simulation.

본 논문에서는 가정용으로 사용하는 3kW 무변압기형 태양광 발전용 인버터에 대하여 설명한다. 지금까지 국내에서 생산되고 있는 태양광 발전용 인버터는 외산을 제외하고는 상용 주파수의 변압기를 장착한 형태로서 계통에 안정적이고 제어가 간단하지만 부피가 크고 무게가 무겁고, 또한 태양전지의 입력 전압 범위가 좁다는 단점을 가지고 있다. 이를 개선하기 위해서 승압형 DC-DC 컨버터를 추가하여, 변압기 없이 컨버터와 인버터로 구성된 시스템을 소개하고 구성 및 특성에 대해서 알아본다.

본 논문에서는 연료 전지 전압의 왜란 보상을 위해 Z-소스 인버터와 울트라커패시터를 포함하는 연료 전지 시스템을 제안하였다. Z-소스 인버터는의 구조는 매우 간단하며 DC/DC 컨버터의 사용 없이 단순히 스위칭 패턴만을 제어하여 전압을 부스팅 할 수 있는 독특한 특징을 갖는다. 연료 전지시스템은 부하 변동시 외부적인 영향에 의해서 과도 상태 전압 왜란이 발생할 수 있다. 시뮬레이션결과는 Z소스 인버터와 울트라커패시터를 포함한 제안된 연료 전지 시스템이 시스템 과도 상태와 전압 왜란에 대해 안정된 응답을 갖고 동작 가능하다는 것을 보여 주었다.

본 논문에서는 연료전지 자동차와 같은 하이브리드 시스템에서 양방향 DC-DC 컨버터에 의한 충${\cdot}$방전 동작시 원하는 지령전력을 정확히 제어하여 연료전지의 과부하에 의한 전지수명단축과 연료이용률저하에 의한 연료소모 문제를 개선하기 위한전력제어기를 제안하고자 한다. 또한 연료이용률과 배터리의 SOC를 일정하게 제어하여 에너지를 효율적으로 사용하기 위한 양방향컨버터의 충${\cdot}$방전운전 알고리즘을 제안한다.

In this paper, a new SEPIC-Flyback converter with a single transformer has been proposed, which is suitable for a fuel cell based power generation system. The proposed converter is superposition of sepic and flyback converter mode. It has outstanding high boosting output voltage, component utilization and high efficiency characteristics under the inherently severe low output voltage of the fuel cell generator. The proposed converter for a full cell generator is described and verified by simulation and experimental result that make used of the Polymer Electrolyte Membrane Fuel Cell(PEMFC) Generator.

In this paper, standard model for electrical power subsystem of a satellite simulator is presented and analyzed. The main purpose of standard model simulator is to promote platform independency, interoperability and reusability of simulation models. And, EPS simulator prototype model is proposed using the SMP2 standard.

KHSR(Korean High Speed Railway) had achieved the maximum speed of 350 km/h last year. And then, we have concentrated to improve the reliability of the overall system, in particular, motor block of the locomotive. In this paper, simple technique for operating PWM converters under the voltage distortion is introduced. In addition, the electrical braking technique is also made to have the braking capability under the dead zone. Test results revealed the verification of the proposed techniques.

The smelting system using induction heating technology has many advantages over conventional fossil fuel regarding energy efficiency, environmental aspect and so on. This paper introduces the principal and technical trends of Induction heating technology, and describes recently developed 2500kW induction smelting inverter, The developed inverter is a series resonant type using high speed Thyristor (SCR) and employs state-of-art digital controller using DSP.

In this paper, the microcontroller TCP/IP NIE(Network Interface Equipment) which is exclusive of an operating system is implemented and the applied example to a step motor motion controller is then explained. The microcontroller TCP/IP NIE supplies a DHCP(Dynamic Host Configuration Protocol) as well as basic TCP/IP network protocols. So, the automatic setting up of the Dynamic If(Internet Protocol) is possible. To implement a control of a system with an internet, the microcontroller TCP/IP NIE is applied to a step motor motion controller and a step motor is then controlled with a Microsoft Windows-based Telnet application program.

AC harmonic filters connected to the terminals of HVDC schemes fulfill two primary functions: to compensate for part or all of the reactive power absorbed by the converter, and to limit to an acceptable level the voltage distortion caused by the converter harmonics. this paper makes a direct comparison between tuned filters and damped filters, each designed for a long HVDC transmission scheme. It Is hoped that by comparing the two approaches a syudy to determine the suitability of filter types to AC systems can be promoted.

High efficiency and low cost sustain driver for plasma display panel (PDP) with current fed is proposed. Main concept of the proposed circuit is using the current source to charge and discharge panel. As a result, all power switches can achieve the zero voltage switching (ZVS) and every auxiliary switch can also do the zero current switching (ZCS). Moreover, since the inductor current can compensate the discharge current, the current stress of all power switches can be reduced considerably. Furthermore, it has features as a simpler structure, less mass, less cost, and lower electromagnetic interference than prior circuit.

Plasma display panel (PDP) has a serious thermal problem, because the luminance efficiency of the conventional PDP is about 1.5 lm/W and it is less than $3{\sim}5$ lm/W of cathode ray tube (CRT). Thus there is a need for improving the luminance efficiency of the PDP There are several approaches to improve the luminance efficiency of the PDP and we adopt the driving PDP at high frequency range from 400 kHz up to over 700 kHz. Since a PDP is regarded as an equivalent inherent capacitance, many types of sustaining drivers have been proposed and widely used to recover the energy stored in the PDP. However, these circuits have some drawbacks for driving PDP at high frequency range. In this paper, we investigate the effect of the parasitic components of PDP itself and driver when the reactive energy of panel is recovered. Various drivers are classified and evaluated whether it is suitable for high frequency driver, and finally current-fed type with do input voltage biased is proposed. This driver overcomes the effect of parasitic component in panel and driver and fully achieves ZVS of all full-bridge switches and reduces the transition time of the panel polarity.

본 논문에서는 코로나 방전 처리를 위해서 PDM에 의한 전압원 직렬공진인버터의 제어와 동작을 위한 알고리듬을 제안한다. PDM 인버터는 동작주파수와 일정 DC 전압 상태에서 평균 출력 전력을 제어하기 위해서 AC 출력단자에 구형파 AC 전압과 영전압 상태를 생성한다. 또한 스위칭 손실의 최소화를 위해서 영전류 스위칭과 영전압 스위칭을 모든 동작 상태에서 이루어짐을 보인다. 또한 강한 비선형적인 특성을 가진 코로나 방전 부하에 대하여 $5%{\sim}100%$의 폭 넓은 방전 전력을 제어함을 보인다.

This paper describes experimental analysis of UPFC, which is composed of cascaded H-bridge modules and single-phase multi-winding transformers for isolation. The operational characteristic was analyzed through experimental works with a scaled model, and simulation results with PSCAD/EMTDC. The UPFC proposed In this paper can be directly connected to the transmission line without series injection transformers. It has flexibility to expand the operation voltage by increasing the number of H-bridge modules. The analysis results can be utilized to design the actual UPFC system applicable for the transmission system.

본 논문에서는 저가형 PDP 구동 회로를 위한 새로운 단일 스위치 에너지 회수 회로를 제안한다. 제안한 회로는 기존의 에너지 회수 회로가 주스위치 외에 별도로 4개의 스위치가 더 필요한 데 비해 하나의 스위치만을 사용함으로써, 그 구조가 간단하여 작고 가벼우며 저가로 구현 가능하다. 또한 이 회로는 우수한 에너지 회수 성능을 보이며 패널전압을 충분히 충, 방전시킴으로써 모든 주스위치들이 영전압 스위칭하도록 하고 낮은 EMI 특성을 갖는다. 본 논문에서는 제안한 회로의 동작 원리, 설계 방법 그리고 실험 결과를 제시한다. 제안한회로는 PDP TV의 저가격화에 도움이 되리라 기대된다.

A novel full-bridge converter with a new energy-recovery driver implemented a regenerative transformer is proposed to improve the efficiency for wide input voltage range and load variation. The main switches achieve ZVS independent of the load current condition. During the free wheeling period, conduction loss is minimized by recovering the circulating energy to the source. The principle of operation, design consideration and experimental result, including efficiency, are presented in the case of large variation of the input voltage or load. A proposed 1kW converter prototype is compared with a PS-FB converter.

A new high performance energy-recovery circuit (ERC) for a plasma display panel (PDP) is proposed. Two different ERCs are employed on both sides of the PDP, and slow falling and fast rising times are applied. It features a zero voltage switching (ZVS), low electromagnetic interference (EMI), low current stress, high efficiency, no severe voltage notch, reduced sustaining voltage, and high energy-recovery capability.

In this paper, an effective way to develop electrical system for Korean High-Speed Train(KHST) was introduced. High speed train is complicated electrical system that consists of many kinds of control devices, power supplies and communication systems. Due to reason of cost, safety and time for development, it is not so easy to test system performance after construct the high speed train in the test track. For the effective test and verification of system performance, from each electric system test to integration test for all interconnected electrical system are performed to reduce time and cost for development of high speed train.

As the screen size of LCD increases, EEFL(External Electrode Fluorescent Lamp) has been suggested to be applicable as backlight source for LCD . Since the electrodes of EEFL are outside of the tube, EEFL enhances the lifetime compared with CCFL(Cold Cathode Fluorescent Lamp), and a single inverter can drive multiple EEFL tubes of which luminance is uniform Therefore, a compact design can be realized and the cost of EEFL application would be much lower than that of CCFL. Moreover, EEFL inverter has higher efficiency per unit power than CCFL inverter. In this paper, a complementary full-bridge PWM(Pulse Width Modulation) inverter was designed for 32-inch LCD TV backlight which has 20 EEFL tubes and adapted two different driving methods to the EEFL inverter. The validity of this study is confirmed from the experimental results.

Multilevel converters have emerged like a new strategy for energy conversion from medium power to high power. The main characteristic of the topologies classified as multilevel, is the use of commutation devices connected in series, allowing the distribution of the voltage and reducing stress in the commutation switches. Stacked Multicell Converter (SMC), is classified as single-phase voltage source inverter(VSI). Due to the fact, the SMC generates a signal of alternating current of several levels of voltage of direct current. The following work will demonstrate the flexibility of the above mentioned topology using a low cost control circuit architecture.

This paper proposes a modeling of wind turbine simulator which includes the dynamic characteristics such as pitch angle control, torsional vibration, and tower effect. Simulation results using PSCAD are provided to show the wind turbine simulator performance.

In this paper, a new scheme of current programmed control for three phase PWM AC-AC converter is presented. By considering only the magnitude components, a similar scheme in the DC-DC converter can be extended to the three phase PWM AC-AC converter. The proposed current programmed control will be well adopted into various converter topologies though three phase PWM AC-AC boost converter is treated as an example. The converter analysis is carried out by applying the vector DQ transformation to obtain physical insight into the converter operation. Finally, the experiment result shows the validity of the proposed scheme.

In this paper proposes a very simple method to estimate the rotor position of a switched reluctance motor. By on-line estimating the self-inductance of the motor, the rotor position of the SR motor is obtained, and a closed-loop drive system can be achieved. Proposed methods can easy implement to application with sensorless SR motor drive system. Speed 2000rpm SR motor simulation executed with self inductance estimation and result represented. Simulation result verified the rotor position using the proposed self-inductance estimation method.

A bootstrap circuit for floating power supply has the advantage of being simple and inexpensive. However, the duty cycle and on-time are limited by the requirement to refresh the charge in the bootstrap capacitor. Hence, this paper deals with a design of charge pump circuit for a floating gate power supply of an IPM. The operation of the proposed circuit applied by three-phase inverter system for driving induction motor are verified through the experiments.

운전 속도 영역이 넓은 응용분야에서 극수가 많은 전동기를 설계하는 경우, 고속 운전 영역에서는 동기 좌표계 회전 주파수가 샘플링 및 스위칭 주파수에 가까워진다. 이 경우 하위 전류 제어 회로(inner current control loop)가 불안정해지면서 전류가 발산하는 현상이 발생한다. 본 논문에서는 전동기의 고속 운전 영역에서 하위전류 제어 회로가 불안정해지는 이유를 분석하고, 기존에 쓰이던 전류 제어기의 구조를 개선하여 고속에서도 전류 제어를 안정화시키는 방법을 제안한다.

In order to tune the speed controller in the linear servo applications the accurate information of a mover mass including a load mass is always required. This paper suggests the mass estimation method of a permanent magnet linear synchronous motor(PMLSM) by using the parameter estimation method of Least-Squares algorithm. First, the deterministic autoregressive moving average(DARMA) model of the mechanical dynamic system is derived. The application of the Least-Squares algorithm shows that the mass can be accurately estimated both in the simulation results and in the experimental results.

This paper presents a novel, single stage, isolated, three-phase switching rectifier capable of switching at high frequency. The circuit topology Provides zero-voltage switching for all switches, output voltage regulation, unity input power factor, all in a single power conversion stage. Operating principle and experimental results in the 48V/100A DC power supply of three-phase single stage method are presented.

A new high efficiency active clamp forward converter suitable for the sustaining power module(SPM) of a plasma display panel (PDP) is proposed. It has a wide zero voltage switching (ZVS) range without inserting additional resonant inductor. Also, it features simpler structure, lower cost, less mass, and no effective duty loss. Furthermore, voltages across all rectifier diodes are clamped on the output voltage, which results in a higher efficiency.

This paper presents a Zero-Current Switching(ZCS) two-transformer phase-shift full-bridge(TTFB) converter using voltage ripple. The proposed converter provides Zero-Voltage Switching(2VS) of leading leg switches and ZCS of lagging leg switches using volt-age ripple. Especially, circulating current Is reduced by ZCS operation and there are no additional components required for the soft switching of power switches. Furthermore, in case of light load, ZVS operation of lagging leg can be achieved. The operations, analysis and design consideration of proposed converter are presented. To verify the validity of the proposed converter, experimental results for a flow (205V, 2A) prototype are presented.

A new LLC resonant converter with multiple outputs is proposed for high efficiency and low cost plasma display panel (PDP) power module. In the proposed converter, ZVS turn-on of the primary MOSFETs and ZCS nun-off of the secondary diodes are guaranteed in the overall input voltage and output load range. Moreover, the primary MOSFETs and the secondary diodes have low voltage stresses clamped to input and the output voltage, respectively. Therefore, the proposed converter shows the high efficiency due to the minimized switching and conduction losses. In addition, by employing the transformer, which has the two and more secondary side, the proposed converter can have multiple outputs and they show the great cross-regulation characteristics. As a result, the proposed converter can be implemented with low cost and compact size. The 500W prototype is implemented, which integrates the sustaining and addressing power supplies of PDP power module. The maximum efficiency is 96.8% and the respective output voltages are well regulated. Therefore, the proposed converter is suitable for high efficiency and low cost PDP power module.

본 논문에서는 평균전류모드제어를 이용하는 컨버터의 연속시간 소신호 모델을 구한다. 평균전류모드제어에 일반적으로 사용되는 보상기를 적용한 컨버터의 해석을 위해 샘플러를 전류루프에 포함시켜 해석한다. 기존 모델에서는 정확히 해석하기 어려웠던 전류루프 이득의 고주파 영역 해석이 제안한 모델을 이용함으로써 쉽게 해결할 수 있으며, 시스템의 안정성을 결정하는 고주파 영역에서의 주파수 응답 특성을 제안한 모델이 우수한 성능으로 예측 가능함을 보인다.

PDP 유지전원단을 위한 고효율을 갖는 새로운 페이지 쉬프트 풀브릿지 컨버터를 제안한다. 제안된 컨버터는 Rectifier로 Voltage Doubler를 사용함으로서, 큰 사이즈의 Output Inductor가 없게 되어 간단한 구조를 가지게 되며 Rectifier Diodes의 전압 스트레스가 출력전압으로 클램핑되어서 스너버회로가 필요없다는 장점을 가지게 된다. 또한 넓은 영전압 스위칭 구간을 가지며, 트랜스포머의 기생성분인 Leakage 인덕터와 Voltage doubler의 캐패시터간의 공진을 이용함으로서 전류가 작은 RMS값을 가지게 되어서 낮은 도통손실과 Rectifier Diode의 전류 스트레스 또한 낮다는 장점을 가지게 된다. 본 논문을 통해 제안된 컨버터의 동작원리와 해석, 실험을 수행하였다.

In this paper, to report the experimental results the core losses of VRM inductor. The VRM, that has a output voltage 1.5V, output current 60A, maximum power of 90W. Experimental results verify, the VRM has a almost same data of fast transient response, a efficiency test with high flux and ferrite inductor. A maximum power conversion efficiency of the experimental VRM was measured at 92% within 0.2% load regulation.

This paper proposes a new sustaining driver for AC PDP(Plasma Display Panel), which improves the performance of conventional circuit with reduced sustain voltage such as TERES(TEchnology of REciprocal Sustainer). In the TERES circuit, the sustain voltage is the half of general sustaining driver and there is no energy recovery circuit. The circuit proposed in his paper has an energy recovery circuit and removes surge currents. Although the energy recovery circuit is added, the number of active switching elements is the same as the TERES circuit. The operations of the proposed circuit are analyzed for each mode and its validity is verified by the simulations using PSpice program.

As a viable alternative to magnetic transformers in the power supply for portable electronics, this paper presents a miniaturized off-line travel adapter or charger for cellular phones using the piezoelectric transformer. Various design considerations in the design of ac PT adapters are investigated before coming up with the proposed pseudo-resonant topology. A prototype hardware design is also presented and verified by simulations and experiments

Recently, the PDP is the most remarkable media for a next generation display device. But the PDP is a high power consumption device. It is to required a high efficiency power supply. We reported the experimental result the high efficiency PDP power supply for 550w class. The proposed converter is quasi-resonant flyback topology, it achieves soft-switching in the single-switch flyback converter. As a result, we realize to very high efficiency power supply for PDP of 95% at 400v dc input and 550Watt output.

This paper proposes a regeneration inverter system, which can regenerate the excessive power form the DC bus line to the AC source for traction systems. The proposed regeneration inverter system for DC traction can reduce harmonics which is a characteristic of the AC current source. The simulation was composed as a prototype model[3.7kW]. Finally, it is shown that the inverter can successfully operate in regeneration mode.

Recently, the demand for the development of high quality and high speed laser printer and efficient power utilizations are required. Among complicate electro-mechanic devices in laser printer, the toner fusing unit consumes above 90[%] of all electrical energy needed for printing devices. Therefore, the development of more effective energy-saving toner fusing process becomes a significant task of much great demand. Generally, there are several way to implement fusing unit, among them this paper present a new hybrid induction heating method. The proposed induction heating method enables to increase coupling coefficient between heating coil and heat roller also to Increase total energy transfer efficiency. Therefore the proposed IH inverter system provide very fast W.U.T.(Warm UP Time), also high efficiency. Through experimental result, the proposed control system is verified.

Wind farms employs induction generators which are two type, one is Squirrel cage for fixed speed wind turbines and the other is Wound induction generator (doubly fed induction generator DFIG) for variable speed wind turbines. this paper describes grid connection scheme of wind power system using two type induction generators and simulation results show the characteristics of two type induction generators.

이 논문은 제주 해남 HVDC 시스템 Hybrid 시뮬레이터 개발과 그 동특성 및 제어 특성을 실제시스템과 비교 분석하였으며 HVDC 시뮬레이터 개발을 위한 구현 및 검증을 제시하였다. 향후 HVDC와 제주 AC 계통에 대한 계통연계 해석 및 HVDC 설비 문제점 해결을 위한 국내기술 확보와 운전자 교육 자료로 사용될 수 있을 것으로 판단된다.

This paper describes a method for the detection of shorted-turn in the cylindrical synchronous generator rotor windings based on the discrete wavelet transform. Multi-resolution analysis(MRA) based on discrete wavelet transform provides a set of decomposed signals in independent frequency bands. In the proposed method, shorted-turn detection in rotor windings is based on the decomposition of the rotor currents, where wavelet coefficients of these signals have been extracted. Comparing these extracted coefficients is used for diagnosing the healthy machine from faulty machine. Experimental results show the effectiveness of the proposed method for shorted-turn detection in the cylindrical synchronous generator rotor windings.

본 연구는 알루미늄 단조 라인의 가열로 컨베이어에 적용된 6관절 이송용 로봇에 Machine Vision System을 구축 한 것으로 이송용 로봇이 작업 대상물을 적재하기 위한 위치정보를 획득하고 재처리하여 로봇 컨트롤러에 제공하는 비주얼가이던스 기법을 연구하여 이를 적용하였다. 적용된 Machine Vision System이 실제 구동에 있어서 안정함을 확인하였다. Machine Vision System에 적용된 CCD 센서로는 Sony사의 XC-HR50이 적용되었으며 Frame Grabber는 Matrox Meter II 카드가 적용되었다. Machine Vision System 제어기로는 범용PC(2.4Ghz, Windows 2000)를 사용하였으며 제어Software는 Microsoft 사의 Visual Basic 6.0 version을 사용하였다.

국내에서 대체에너지 공급 비율을 보면 청정에너지로 분류할 수 있는 태양열에너지, 태양광 에너지, 풍력에너지를 모두 합하여 대체에너지의 10% 이하이며, 대체에너지 비율의 90% 이상을 폐기물로부터 얻은 에너지가 차지하고 있는 실정이다. 신재생에너지원에는 여러 종류가 있지만 해양에너지원에 대해 대상을 설정하고 이에 대한 부존량을 살펴보면 진도 주변의 해역에서 조류발전 부존량이 약 362만 kW가 되며, 시화호와 새만금 등지에서의 조력발전 부존량이 650만 kW, 동해안 후포 연안을 비롯한 파력발전 부존량이 20만 kW가 되는 것으로 알려져 있다. 이에 따라 해양에너지를 실용화하기 위한 연구가 국내외에서 연구되고 있다. 본 논문은 권선형유도발전기를 갖는 조류발전 시스템을 대상으로 연구한 결과로 권선형유도발전기를 제어하기 위한 전력변환장치 개발과 관련한 내용이다. 신재생에너지원이 발전 단가 측면에서 경제성을 갖기 위해서 발전기 용량은 5MW 급까지 대용량화 되어 있는 단계이지만 국내에서는 아직 MW급 이상이 되는 권선형유도발전기와 권선형유도발전기를 제어하는 전력변환장치에 대한 연구 실적이 없는 상황이다. 이에 본 논문에서는 IMW급의 권선형유도발전기에 대한 개발 사례를 소개하면서 유효전력제어, 역률제어 특성과 운전 속도에 따라 변동되는 회전자 측에서의 피상전력 제어 특성에 대해 고찰하고자 한다.

This paper presents a wavelet-based neural network technology for the detection and classification of the short durations type of power quality disturbances. Transients happen during very short durations to the nano- and microsecond. Thus, a method for detecting and classifying transient signals at the same time and In an automatic combines the properties of the wavelet transform and the advantages of neural networks. Especially, the additional feature extraction to improve the recognition rate is considered. The configuration of the hardware of TMS320C6711 DSP based with 16 channel 20Mhz sampling rate A/D(Analog to Digital) converter and some case studies are described.

In order to reduce the harmonics in invertor output of the DVR system, typically LC filter is employed. In designing the LC filter, it is required to consider the gild impedance and the characteristic of the harmonics. In this paper, problems in the conventional way of designing the LC filter is analyzed and new LC fitter design technique is proposed. In the proposed technique, parameters of the LC filter are calculated considering grid impedance, THD, DC link voltage and phase lag. The validity and feasibility of the proposed method is verified through the simulations experiments. The DVR system with the proposed LC filter is being built and tested.

In this paper, harmonic detecting methods for the active power application are investigated. They are RDFT, Kalman Filter, Adaptive predictive filter, Instantaneous reactive power detecting method, Improved adaptive filter detecting method. The 5 harmonic detecting methods are simulated and their characteristics for the active filter application are compared using simulation results.

This paper presents a unified control scheme for series-type active power filters combined with shunt passive filters for the source voltage unbalance compensation and the power factor correction simultaneously. The power factor correction is achieved by controlling the amplitude of reactive power current in a series filter as zero in a synchronously rotating reference frame. The proposed algorithm successfully compensates the source voltage unbalance and the power factor. The validity of the proposed scheme has been verified by simulation for a 3-kVA hybrid active power filter system.

The improvement of load following operation of the thermal power plant is influenced to the electrical quality. Analysis of boiler, turbine, and governor system, and the study of control algorithm are preceded. The thermal power plant is operated by various control systems. In the case of faulty governor system, it takes long days to solve the problem and impossible to repair the mechanism without outage. A non-planned out-age is taken into consideration because of economical power production. In this paper, to clear the continuous swings of an old turbine governor system(YEOSU #1), the trend, the control logic, and the hydraulic mechanism are analyzed, and then the control circuit with ADAPT function and the 1st order lag circuit are inserted and modified. After that, the power plant comes to automatic governor control operation.

This paper proposes a new neutral current reduction method using PQR instantaneous power theory on the active power filter, unbalanced nonlinear load condition in three-phase four-wire systems. For reduction of neutral line current, the single phase active power filter is used and its performance is same with the three-phase four-wire active power filter. For fully-digital implementation, ramp comparison PWM method was adopted. Simulation results verify good performance of the proposed current control strategy on the shunt APFs.

High voltage pulse power supply using Marx generator and solid-state switches is proposed in this study. The Marx generator is composed of 12 stages and each stage is made of IGBT stack, two diode stacks, and capacitor. To charge the capacitors of each stage in parallel, inductive charging method is used and this method results in high efficiency and high repetition rates. It can generate the pulse voltage with the following parameters: Voltage: up to 120kv Rising time: sub ${\mu}S$ Pulse width: up to $10{\mu}S$, Pulse repetition rate: 1000pps The proposed pulsed power generator uses IGBT stack with a simple driver and has modular design. So this system structure gives compactness and easiness to implement total system. Some experimental results are included to verify the system performances in this paper.

In this paper, the electrical characteristics of the non-contact transformer is presented using conventional coupled inductor theory. In high power applications, the non-contact transformer is so bulky and heavy that it poses some maintenance problems. Therefore it should be divided into some light transformer modules. This paper shows the analytic method of how to measure the parameters of the multiple connected non-contact transformer The analytical results are verified through measurement.

This paper presents the performance results of roof-integrated 3kW PV (Photovoltaic) system by field testing. Form these results, the loss factors of PV system are compared and analyzed.

본 논문에서는 연료전지를 이용한 가정용 발전 시스템의 계통 연계를 위한 새로운 단상 인버터 시스템을 제안한다. 제안한 방식에 의해 역률 1에 가까운 전원 품질로 독립 운전과 계통연계 운전이 가능하고 자동 모드 전환시 최소의 과도상태를 갖는다. 또한 제안한 인버터 제어기는 연산이 적고 구조가 간단하여 저가격의 고정소수점 DSP로 구현이 가능할 뿐 아니라 정상상태 오차가 거의 없고 양호한 과도상태 응답특성을 얻을 수 있다. 제안한 계통연계형 인버터의 제어기에 관하여 기술하고 모의실험 및 실험에 의하여 그 타당성을 입증한다.

Islanding phenomenon is undesirable because it lead to a safety hazard to utility service personnel and may cause damage to power generation and power supply facilities as a result of unsynchronized reclosure. In order to prevent this phenomenon, various anti-islanding methods have been studied. Even though the slip mode frequency shift (SMS) method has been regarded as a highly effective anti-islanding method, the analytical design method of that was not cleared. This paper proposes a modeling of the SMS method using non-detection zone (NDZ) and evaluation of the method according to the test conditions of IEEE Std. 929-2000. The SMS method is derived analytically through the modeling and verified visually by simulation and experiment.

In this paper, electronic-controlled power supply(EPS) system for solar cell characteristic is proposed to solve various problems and to achieve reliable experimental result on photovoltaic system. This system emulates the solar cell output characteristics, and it can substitute solar cell in laboratory experiment system. New model for solar cell is proposed to realize the EPS system for solar cell, which is based on the interpolation. Both simulation and experiment are executed to show the validity of the proposed EPS system.

Nowadays, more than ever before, many researchers are paying attention to raising the efficiency of a Power converter. In Flyback converter, the resistor of RCD snubber consumes the stored energy in leakage inductor. It play a role in degrading the overall system efficiency Thus, In this paper, a novel energy recovery circuit of Flyback converter is proposed to improve the efficiency. The operational principle of the proposed circuit is explained in detail. And, it is verified through the simulation results.

This paper proposes a compact pulse generator fur NOx removal application for diesel automotive. The rising time is important factor to increase NOx removal efficiency in pulsed corona discharge method. Manufacturing cost and compactness of the pulse power generator should be satisfied for automotive application. The proposed pulse power uses a low voltage thyristor, a pulse transformer with the function of saturated magnetic switch, and series connected general diodes as opening switch to satisfy that requirements. With 200 resistor load, the experiment results show that the output voltage is 21kV, the rising time is about 21ns, and the pulse width (FWHM) is about 42ns.

본 논문은 신${\cdot}$재생에너지원을 이용한 분산전원용 계통연계 인버터의 전류고조파저감에 관한 연구로서 전류고조파는 진력풍질 측면에서 중요한 요소 중의 하나이나 전원전압의 불평형, 왜곡 및 부적절한 전류제어기의 조정 등의 원인으로 인하여 이런 목적의 달성이 어렵게 된다. 전류제어기법 중에는 동기좌표게 상에서 동작하는 전향보상부 PI 제어기가 일반적으로 사용되고 있으며 본 논문에서는 전원전압 왜곡 하에서 전류제어기 이득과 전류고조파의 관계를 분석하고 Particle Swarm Optimization(PSO) 알고리즘을 이용하여 PI 제어기를 최적 조정하는 방법을 제안하였으며 모의시험과 적용실험을 통하여 그 유용성을 입증하였다.

최근의 산업용 서보 구동 응용 분야에서는 전 운전 영역에서 위치 추종에 대한 높은 정밀도와 빠른 응답 특성이 요구된다. 그러나 부하 외란은 시스템의 속도 응답 특성을 나쁘게 하여 위치 추종에 대한 빠른 응답 특성과 높은 정밀도를 기대하기 어렵게 만든다. 따라서 고성능 위치/속도 제어를 위해서는 부하 토크의 추정이 필수적이다. 본 논문에서는 SVR에 기반한 실시간 부하 토크 관측기를 제안한다. 제안된 방법은 오프라인 SVR 학습을 통하여 부하 토크 관측기를 만들고, 운전 데이터로부터 부하 토크를 추정하여 실시간으로 전향 보상한다. 제안된 방법의 타당성을 위해 다양한 실험을 수행하였다.

Most realistic control systems contain nonlinearities of some form. One nonlinearity commonly found in control systems is a saturating element. If integral control is applied to such a system to eliminate steady state error, an undesired side effect known as integrator windup may occur when lage setpoint changes are made. This effect leads to a characteristic step response with a large overshoot and a very high settling time. To avoid this situation, many different anti-windup strategies have been suggested. But existing strategies remain over shoot and high settling time. This paper proposes a new anti-windup strategy for PI speed controllers. When the speed control system is changed P controller to PI controller. Integrator has an appropriate initial value. This value results over shoot and high settling time. The SIMULINK/MATLAB-based comparative simulation results and experiment results of speed controller have shown its superior control performance to that of a proposed anti-windup speed controller.

This paper proposes an algorithm for the moment of inertia estimation. The algorithm finds the moment of inertia observing the position error signal, which contains an error information of moment of inertia, generated by speed observer. Moreover, the proposed algorithm is easily realized in the observer -based speed detection method. The experimental results are also presented to confirm the performance of moment of inertia estimation method. The results show that the moment of inertia converges to the actual value with the proposed method.

This paper proposes a unity power factor ZVT PWM single-phase rectifier. The ZVT soft switching are achieved by using a simple ZVT circuit, and the reduced conduction losses are achieved by employing a single-stage converter, instead of a typical double-stage converter composed of front end diode rectifier and cascaded boost rectifier. Furthermore, thanks to good features such as simple PWM control at constant frequency, low switch stress and low VAR rating of commutation circuits, it is suitable for high power applications. The principle of operation is explained in detail, and simulation results of the new converter are also included.

Bidirectional DC/DC converters allows transfer of power between two dc sources, in either direction. Due to their ability to reverse the direction of flow of power, they are being increasingly used in many applications such as battery charger/dischargers, dc uninterruptible power supplies, electrical vehicle motor drives, aerospace power systems, telecom power supplies, etc. This paper proposes a new bidirectional Sepic/zeta converter. It has low swicthing loss and low conduction loss due to auxiliary communicated circuit and synchronous rectifier operation, respectively. Because of positive and buck/boost-like DC voltage transfer function(M=D/1-D), the proposed converter is very desirable for use in distributed power system . The proposed converter also has both transformerless version and transformer one.

This paper deals with a simple structured voltage disturbance generator for power quality improving devices. The proposed generator can be applied to the performance test of custom power devices. Voltage sag, swell, outage, unbalance and phase jump after outage are provided by the generator. The improving phase jump operating principle of the generator is described and analysed. The usefulness of the generator is verified through simulation.

This paper proposed a hydraulic pump system that is driven by a variable SR drive. The operating pressure of hydric pump is limited by the pump speed and the mechanical structure. The operating of hydraulic pump is separated as constant pressure and constant flow region. Under fixed speed, the pressure can be controlled as constant value, and then decreased by increasing of pump speed. A 2.2[kW], 12/8-pole SR motor and DSP based digital controller are designed and tested for hydraulic pump system. The test results show that the system has some good features such as high efficiency and high response characteristics.

This paper describes a novel method of detecting excitation position in switched reluctance motor(SRM) drive. Some strategies of position sensorless control methods for the motor include the measurement of phase current and applied pulse voltage in an unexcited phase is suggested. The principle of the estimation of a rotor position is based on the detection of inductance by pulse currents. This sensorless method is very simple to detect excitation position estimation and gives efficient control of drive system. Suggested method is verified by some simulations.

This paper presents the reasonable design parameters of a SRM for hybrid electric vehicle driving. For the design of SRM, the initial model is designed using the equivalent magnetic circuit method. In order to optimize the SRM for HEV. The initial model is redesigned by FEM with the variation of the stock length and turns of winding. This paper shows that a flat-topped current of a phase can be made from a change of the stack length and the number of turns for high efficiency, high average torque and a lower torque ripple. The change of current falling time as a variation of turn-off angle was shown by FEA. The iron loss and copper loss were described. The torque of the redesigned motor is suitable for low and high speed ranges to drive a HEV that was verified by the speed-torque curve.

This paper presents dynamic characteristics of super high speed SRM and it's drive. The nonlinear model of super high speed SRM is implement by Matlab/simulink and the simulation results show that the prototypeSRM can operate up 20,000[rpm]with stable performance.

Recent interest in the synchronous reluctance motor has increased in possible applications such as home appliance, hybrid electric vehicles, etc. This paper presents a brief review of the research and development of synchronous reluctance motors, carried out up to now, from the designers' viewpoint. In addition, the key points in the design of synchronous reluctance motors and a new design method for innovating on their rotor structures are discussed.

In this paper, a compensation scheme for the effect of dc-link ripple voltages on output voltage of two-leg and three-phase PWM inverters is proposed, without which compensation scheme the three-phase output voltage and current are much distorted. The proposed scheme has been verified by experimental results.

This paper proposes the SRM drive system based on DC-link current, from which the phase currents can be estimated in accuracy and also they can be used in driving SRM instead of the three-phase currents. In additional, the detecting circuit for DC-link current is also proposed for increasing the resolution and decreasing the off-set. Comparing to the general drive system based on the phase current, it is verified through the experiment that the proposed SRM drive system has the good performance in steady-state responses of the speed control. Using the DC-link current, all of the 3-phase currents can be easily estimated in driving the SRM.

This paper proposes the algorithm for the initial pole-position estimation of a surface PM-LSM, which is carried out under the pseudo-position control with-out a pole sensor and is insensitive to the motor parameters. This algorithm is based on the principle that the initial pole-position is calculated by the reverse trigonometric-function using the two reference currents, which are informed from the speed controller. The effectiveness of the proposed algorithm is confirmed by the arithmetical analysis and the experiment. IPP is well estimated within a satisfied moving-distance and a shorter estimation taken-time even if large disturbance such as cogging and friction are existed.

The paper is final report for speed control upgrade and analysis report which recently performed on PWR NPP safety related EDG KHNP Ulchin NPP No.2 Unit. The upgraded system includes more beneficial function like as 'Slow start with starting ramp', 'Generator load sensing & control capability' and 'Emergency ramp during slow start'. This paper shows functional operation of slow start regime according to NRC regulatory guide which guide regulation to NPP safety related environment.

The stroke of piston in the linear compressor driven by LPMSM can be obtained from integrating the input voltage and current of LPMSM, and may be diverged due to dc components In the voltage and current. The strategy to prevent the divergence of stroke using both the high-pass filter and dc offset compensation was suggested. The equations for the magnitude and phase of the stroke and also dc offset including the stroke are derived as a function of the cut-off frequency of HPF. The performance of stroke calculation scheme has been verified by experimentally on a linear compressor drive system, where the control was implemented by a 16-bit DSP.

In this paper, the PWM inverter-motor drive system including sensor is controlled through the network. The algorithm to compensate for the time delay of ac current and ac voltage sensors due to the network is proposed. The delay time of sensors is kept nearly constant, using the synchronous signal and timers. The error between the real and estimated ac signals can be reduced by using two slopes for estimating the value of at signals. The proposed algorithms are verified with the simulation studies and experiments.

Islanding of PV systems occurs when the uitilty grid is removed but local sources continue to operate and provide power to local loads. Islanding Is one of the serious problems in an electric power system connected with dispersed power sources. Also, this scan present safety hazards and the possibility of damage to other electric equipments. If the real and reactive power of RLC load and PV system are closely matched, islanding phenomena can't be detected by the passive methods. Several active methods were proposed to detect islanding phenomena. The most effective method is SFS method which was suggested by Sandia National Laboratory. In this paper, a new anti-islanding algorithm is proposed and its validity is verified through simulation and experimental results for utility interconnection of PV system.

This paper shows the development of remote control system for manipulators which consists of PHANToM Device as a master, Samsung FARA robot as a slave and TCP/IP based LAN fortheir Communication. This work includes the motion mapping between the master and the slave, Generation of virtual viscosity force preventing operator's unwilled action and 3D remote control simulators for the stable operation of the remote control system, etc. The remote control implementation has been performed and the results shows that the developed system can allow the operator to effectively control the manipulator.

본 논문은 무선 LAN기반에서의 이동로봇에 Manipulator를 장착하고 안정된 원격 제어를 수행하였다. 원격제어는 웹 카메라 및 레이져 센서를 통해 이동로봇 주변 환경을 인식할 수 있으며, 조이스틱을 이용하여 이동로봇 및 Manipulator를 제어한다. 무선 랜 기반 원격제어 시스템은 환경조건에 따라 통신지연이 불규칙하고 통신두절의 발생가능성이 매우 높다. 본 논문은 이러한 문제점이 발생할 경우 문제점을 해결하기 위하여 실시간 화상 전송에 대해 이론적이고 체제적 분석을 실시함으로써 보다 안정된 효과를 얻는다. 그리고 조작자가 이동로봇을 좀 더 안정적이고 쉽게 조작 할 수 있도록 하기 위해 힘 반영 조이스틱에 이동 로봇 주위의 장애물 정보를 반영하였다. 또한 Manipulator의 원격조정 알고리즘을 개발하여 보다 안정되게 물체를 파지 및 이동시킬 수 있다.

본 논문에서는 전방향 등극기하를 이용하여 이동로봇의 효과적인 표식대응에 대하여 기술한다. 전방향 영상에서 등극점과 등극선의 특성에 따라 추출된 특징의 영상내 위치를 추정한다. 예측된 특징의 영상위치정보를 통해 효과적인 특징 대응을 하며 본 연구에서는 두영상에서 8개의 대응점을 이용하여 기초행렬 F를 구하고 이것으로 특징의 공간정보를 계산한다. 따라서 기초행렬 F에서 계산된 기초행렬 E로부터 로봇은 자신의 위치와 운동정보(회전, 병진운동)를 알 수 있다. 또한 효과적인 특징대응을 위해 탐색범위를 축소함으로써 계산시간의 단축과 강인한 특징대응을 제시하였다.

오늘날 통신 기능을 갖는 마이크로 프로세스 기반의 IED(Intelligent Electronic Device)가 송배전시스템 분야에서 기존의 장비들을 대체하고 있다. 단일 표준화 작업이 이루어지기 전 다양한 프로토콜의 사용에 따른 장비 간 호환성 결여로 통신 프로토콜 표준화 필요성이 강하게 제기되었고, 1990년대 표준화 작업을 시작하여 최근 변전소 자동화용 단일 세계 표준인 IEC 61850이 UCA2.0과 유럽의 경험을 기반으로 IEC주관아래 개발되었다. 이러한 세계기술 동향을 반영해 IEC 61850 기반의 종합변전소 자동화 시스템의 구축이 필요하고, 이에 따라 본 논문에서는 IEC 61850 통신 프로토콜을 살펴보고 기본적인 IED 통신 실험 장치를 구성하고 메시지 전송 실험을 수행하였다.

쿼리에 응답하는 데이터 전달방식에서는 일반적으로 쿼리가 네트워크 전체에 뿌려진다. 하지만 쿼리가 특정지역의 정보만을 요구하는 경우 그 쿼리는 네트워크 전체에 뿌려질 필요가 없다. 본 논문에서 우리는 제한된 쿼리 전달 기법을 제안한다. 제안된 기법은 네트워크를 섹터와 레벨단위의 논리적 영역을 만들고 쿼리가 필요로 하는 정보가 속한 최소한의 영역으로만 쿼리를 전달함으로써 불필요한 쿼리 전달을 줄이고자 하는 것이다. 성능평가에서는 제안된 기법을 사용함으로써 센서 노드들의 평균 소비되는 에너지를 줄이고 네트워크의 생존시간을 늘리는 결과를 보였다.

본 논문에서는 필드버스 시스템을 위하여 IEEE 1451을 적용한 스마트 모듈을 개발하였다. IEEE 1451은 공장 자동화 시스템에서 스마트 트랜스듀서의 개발을 위하여 제안된 프로토콜이다. 이러한 IEEE 1451이 필드버스 시스템을 위한 스마트 모듈에 적용되면, 네트워크 프로토콜에 독립적인 스마트 모듈의 개발이 가능하다.

오늘날 공장 자동화에 이용되는 필드버스 네트워크는 여러 가지가 있으며 이들은 각각의 미디어 접근 방식과 프로토콜을 사용하고 있다. 이러한 필드버스 네트워크는 완전히 분리되어 있기 때문에 네트워크 관리자는 이를 관리하는데 많은 어려움을 겪고 있다. 본 논문에서는 이기종의 필드버스 네트워크를 통합할 수 있는 필드버스 프로토콜 변환 게이트웨이를 설계하였다. 필드버스 프로토콜 변환 게이트웨이는 프로토콜 변환을 하여 다른 종류의 네트워크로 데이터를 전달할 수 있고 분리된 네트워크를 통합하고 통합된 환경으로 제어 및 모니터링을 가능하게 한다.

An $H_2$ tracking controller is proposed for networked control systems. The network induced delay is assumed to be time varying and vary in the known range. The proposed controller guarantees stability and $H_2$ performance for all time varying delay in the known range. The proposed controller is verified using a simple networked motor control system.

OPC has made it to improve the development of control and monitoring software. But it is difficult to understand COM/DCOM model that is a base technology of OPC and complex communication setting between OPC Server and OPC Client. Therefore, in this paper, we design and implement ActiveX based components that are enable to solve these problems. Implemented components provide a method for simple communication between OPC Server and OPC Client and a GUI environment for easy and fast setting of communication information. Also, they provide the architecture for efficient management of OPC Server's data. By using implemented component, easy development and efficient maintenance of OPC Client can be supported.

This paper presents a new data classification method using the Robbins Monro stochastic approximation algorithm k-nearest neighbor and distribution analysis. To cluster the data set, we decide the centroid of the test data set using k-nearest neighbor algorithm and the local area of data set. To decide each class of the data, the Robbins Monro stochastic approximation algorithm is applied to the decided local area of the data set. To evaluate the performance, the proposed classification method is compared to the conventional fuzzy c-mean method and k-nn algorithm. The simulation results show that the proposed method is more accurate than fuzzy c-mean method, k-nn algorithm and discriminant analysis algorithm.

본 논문에서는 정상적으로 가동 중인 발전소에서 운전되는 기기들의 유량 변화 시 발생되는 음향신호를 분석하고 또 유량의 누설과 비누설시의 음향 변화를 분석하여 누설탐지의 가능성을 보였다.

차량 내에 장착되는 전장품의 기능과 성능의 중요성은 점점 중요해지고 있다. 이에 따라, 자동차 내의 멀티미디어 기기인 오디오, 내비게이터, 스피커 등을 네트워크로 연결하여 사용자 편의성을 증대하고 첨단화 하는 시도로써 MOST(media oriented systems transport) 네트워크가 제안 되었다 네트워크 통합화의 추세에 따라, 멀티미디어 전용 네트워크인 MOST를 차량용 제어 네트워크인 CAN에 접속하여 그 성능을 평가한다.

We propose a charge/discharge model for network based vehicle. These model include motor, alternator, lamp, brake, window brush, air conditioner, etc.. Also, we simulate these models in Matlab. The simulation results show that error range is less than 3%. So, we can adopt these model to charge/discharge simulator for network based vehicle. If this error range can be shrunk within 2%, we can use this simulator for comertial use.

This paper proposes a modified space-vector pulse width modulation (PWM) strategy which can restrict the common-mode voltage for three-phase to three-phase matrix converter and still keep sinusoidal input and output waveforms and unity power factor at the input side. The proposed control method has been developed based on contributing the appropriate space vectors instead of using zero space vectors. The advantages of this proposed method is to reduce the peak value of common-mode voltage to 42% beside the lower high harmonic components as compared to the conventional SVM method. Hence, the new table is also presented with the new space vector rearrangement. Furthermore, the voltage transfer ratio is unaffected by the proposed method. A simulation of the overall system has been carried out to validate the advantages of the proposed method.

The paper discusses the main problems in induction motor diagnosis by motor current and vibration signals, possible faults and effects produced by these faults in the signal spectrums. Decision Tree is introduced as a tool to diagnose the motor status, this expert system is implemented to detect the incipient defects, supervise and predict them, and plan the maintenance of the motor.

The paper aims on an analysis for dc boost control using Z-source inverter. The modified space vector PWM method is used for controlling both the dc boost and ac output controls in the Z-source inverter. The capacitor voltage and the voltage stress of device with both the shoot-through time and modulation index are analyzed considering the zero state time of inverter. The theoretical analysis is verified with the simulation studies and experiments with 32-bit DSP.

In this paper, an efficient switching pattern to equalize the size of transformer is proposed for a multi-level inverter employing cascaded transformers. It is based on the prior selected harmonic elimination PWM(SHEPWM) method. Because the maximum magnetic flux imposed on each transformer becomes exactly equal each to each, all transformers can be designed with the same size regardless of their position. Therefore, identical full-bridge inverter units can be utilized, thus improving modularity and manufacturability. The fundamental idea of the proposed switching pattern is illustrated and the analyzed theoretically. The validity of the proposed switching strategy is verified by experimental results.

In this paper, we proposed the electric circuit using one common arm of H-Bridge Inverters to reduce the number of switching component in multi-level inverter combined with H-Bridge Inverters and Transformers. and furthermore we suggested the new multi-level PWU inverter using PWM level to reduce THD(Total Harmonic Distortion). and we used the switching method that can be same rate of usage at each transformer. Also, we tested the proposed prototype 9-level inverter to clarify the proposed electric circuit and reasonableness of control signal for the proposed multi-level PWM inverter.

In this paper, we proposed the novel hybrid multi-level inverter using combination of the output voltage of transformers to reduce the THD(Total Harmonic Distortion) and improve the waveform of output voltage. The proposed multi-level inverter used the output of transformer which is 1times, 2times, 4times of input of the transformers. So we increased the output voltage from the reduce the number of switching component and transformer. Also, we tested the proposed prototype 15-level inverter to clarify the proposed electric circuit and reasonableness of control signal for the proposed multi -level PWM inverter.

This Exploiting monitoring program is a program for real-time monitoring the current and voltage that made from wind and solar generators. and this program helps to check efficiency and situation of the wind generator, The main subject of this thesis is about making the more useful real-time monitoring program to get and save the data from wind generator. therefore, it uses LabVIEW for this real-time monitoring program.

Recently the study on the new and renewable energy is being addressed and the application examples about it are also increasing as greatly as possible. In this paper, the battery charge controller of street lamp power using wind and solar energy is made and tested.

Normally, the buck converter is used for the charging converter of photovoltaic generator because this converter has good characteristics compare with boost and buck-booster converter But, in case of the sollar-cell voltage is lower than charging voltage, we cannot charge the sollar energy to the charger. So, in this paper, we proposed the novel hybrid converter using by combination of buck and boost converter for the charging converter of photovoltaic generator, as a results, it can operate buck, boost and buck-boost mode. The proposed novel converter has the same characteristics of the existent buck converter and furthermore it can operate as a boost converter. So, we can make the more effective photovoltaic charging system.

In this paper, we proposed the electric circuit using one common arm of H-Bridge Inverters to reduce the number of switching component in multi-level inverter combined with H-Bridge Inverters and Transformers. and furthermore we suggested the new multi-level PWM inverter using PWM level to reduce THD(Total Harmonic Distortion). and we used the switching method that can be same rate of usage at each transformer. Also, we tested the proposed prototype 9-level inverter to clarify the proposed electric circuit and reasonableness of control signal for the proposed multi-level PWM inverter.

This Paper presents a 6 pulse shift operation control mode of current-source-inverter to make improvement of efficiency and to reduce the frequency of inverter switching for photovoltaic generation system using PWM current-source-inverter. This system is connected solar cell energy directly without using a storage cell. The proposed circuit can maintain maximum voltage of photovoltaic generation of take advantage of six Buck-Boost converter and a full-bridge inverter determines the polarity of AC output. That is controlled by using digital signal processor TMS320F2812 for operation about a 6 pulse shift operation control of current-source-inverter, and it is verified through the experimental results.

Recently the study is being addressed on the energy economy as greatly as possible. The researches on light source that have higher efficiency than the exiting are performing. The high-power LED is the representative one among those. There are two fields in the research on the high-power LED, the ordinary illuminating apparatus and the night illuminating apparatus using wind and solar energy. In this paper, we validated the probability of using high-power LED as illuminating apparatus and proposed the novel LED power equipment that has more stability and better efficiency than the exiting method. By using the propose method the -R-E-A-C-T is reduced and the efficiency improved.

Francis turbine of commercial small hydro -power plants under 10kw which is investigate a flow characterist and an efficiency in the research which it sees, the problem and an improvement is investigate. In the research which it is simply model with casing, guide-vane, runner, draft tube for simulation numerical analysis of small-sized Francis turbine. model uses the Gambit and it composes with approximately 800,000 nonuniform lattices. Solutions are investigate the hydraulic characteristics against an outward angle of guide vane, the number of guide vane, head(inlet velocity) by using FLUENT which is a commercial business code.

Among many other alternative energy resources, small scale hydropower has been brought into attention as a reliable source of energy today, which had been relatively neglected since 1960s. Present low head of Francis turbines and small scale hydro turbines, however, have limitations in the minimum required head and flow rate for efficient operation. This study attempts to develope the Francis turbine which is expected to run efficiently even in very low head and small flow rate, so that the limitations on the conventional small scale hydropower could be alleviated and competition with other alternative energy sources in the changable design conditions could be attained. The Francis turbine of a new concept was designed based on changable design conditions, hydrodynamics and theory of power transmission.

We propose a robust adaptive fuzzy controller for the transient stability and voltage regulation of a single-machine inflnite bus power system. The proposed control scheme is based on the input-output linearization to eliminate the system nonlinearities. To deal with uncertainties due to a parameter variation or a fault, we introduce fuzzy systems with universal function approximating capability which estimate the uncertainties on-line.

An adaptive fuzzy sliding-mode controller (SMC) for uncertain or ill-defined single-input single-output (SISO) nonaffine nonlinear systems is proposed. By using the universal approximation property of the fuzzy logic system (FLS), it is tuned on-line to cancel the unknown system nonlinearity. We adopt a self-structuring FLS to guarantee global stability of the closed-loop system rather than semi=global boundedness. The control and adaptive laws are derived so that the estimated fuzzy parameters are bounded and the sliding condition is satisfied.

Recently, There has been growing interest in Distributed Generations with high-energy efficiency due to the Increasing energy consumption and environmental pollution problems. but an insertion of Distributed Generations to existing power distribution system can cause several problems such as voltage variations, harmonics, protective coordination, increasing fault current etc, because of reverse power. This paper was applied to Sukumar M[l] proposal schemes and identity the faulted section performing short-circuit analysis by MATLAB program to distribution systems interconnected a large number of distributed generations.

According to the second scheme of the Korean Government about technology development, utilization and popularization of new ${\cdot}$ renewable energy, the continuous growth of distributed resources are expected. But there is a few paper about recloser and sectionalizer coordination and protection scheme in distribution system interconnected a number of distributed resources. In this paper, it is dealt with that recloser and sectionalizer coordination at the cases concerned with position among protection devices. Adding distributed resource, the problems of each case are investigated through simulation.

This paper presents a 3kW grid-connection photovoltaic power generation system and its topology. Photovoltaic system must provide the sinusoidal output voltage wave for unity power factor High frequency switching converters are becoming more popular because of several benefits which are essential in power conversion system. This paper introduces a high speed digital controller using TMS320F2812 DSP chip which can be used for high frequency switching converters. The experimental results of the proposed PWM Inverter demonstrates its high performance with unity input power factor having very low distorsion in input current waveforms and good dynamic characteristics at full load.

In this paper, we proposed the electric circuit using one common arm of H-Bridge Inverters to reduce the number of switching component in multi-level PWM inverter combined with H-Bridge Inverters and Transformers. and we proposed the switching method that can be same rate of usage at each transformer. Also, we tested the proposed prototype inverter to clarify the proposed electric circuit and reasonableness of control signal.

This paper summarizes the results of these efforts by of offering the PV generation system with solar tracking. The status of PV generation system with solar tracking components and interconnection and effects are summarized. Hence this paper duscusses only points that might be useful for application.

A photovoltaic panel is a device that, through the photovoltaic effect, converts luminous energy into electric energy. Photovoltaic generation system uses infinity of solar energy, cost of fuel is needless and there is no all pollution or waste occurrence. This paper summarizes the results of these efforts by offering a photovoltaic system structure in 50kW large scale applications installed In Chosun University dormitory roof. The status of PV system components, are inter-connection and safety equipment monitoring system will be summarized as this article. This describes configuration of utility interactive photovoltaic system which generated power supply for dormitory In this paper represent 50kw utility PV system examination result

The application of solar energy, in the field of alternative energy, was on the increase tendency. In the case of advanced nations, through continuous R&D, solar hot water heater with high efficiency has been used for the house and the industrial process on business, advanced nations were reached up the experimental stage of solar generation system. But, the actual circumstance of the domestic has been not accomplished the popularization of solar hot water heater and the settlement of it which is the fundamental stage of the solar energy usage. This trouble, the domestic was flooded with small enterprise for producing solar hot water heater, was caused by the popularization and the production without verification of performance. To supply the monitoring program for evaluating solar hot water heater, this research was purpose to improve the technical development of the enterprise for producing solar-heat hot-water-boiler and served as an aid for the enlargement and the popularization on solar energy.

Solar cell converts sunlight into the electricity that one of the most versatile forms of energy. It has been developed and applied on residental electric power system by urbanized countries as a alternative energy source to overcome energy problem after oil shock. This paper summarizes the results of these efforts by offering a snapshot of the configuration of photovoltaic in residential applications. The status of PV system components and inter -connection and safety equipment will be summarized. Hence this paper discusses only points that might be useful for application.

본 연구는 신재생에너지의 하나인 태양광 발진의 소형 발전의 활용분야의 하나로 기존 정원 보안등의 전력원을 상용전원에서 태양전지로 변환하여 직용, 실증화한 연구 결과로서 태양전기 전원의 특성과 배터리의 노화, 반사갓의 차이점을 실증화 시험을 통하여 분석하였으며 각각의 실험결과들은 웹을 통하여 원격 모니터링이 가능하도록 시스템을 구성하였다.

This paper presents experimental operation with utility invertactive 3kW photovoltaic generation system. And that describe configuration of utility interactive photovoltaic system which power supply for Demonstration experiment. The status of photovoltaic generation system comp-onents and interconnection and safety equipment will be summarized. This paper discusses property operation state which system endure division of power for demonstration experiment.

This paper describes a simple pseudo-random carrier modulation technique for the acoustic noise reduction of the three phase multi-level inverter based motor drives. The proposed method generates a new pseudo-random carrier by randomly synthesizing a carrier with fixed frequency and a carrier with opposition phase. To confirm the validity of the proposed method, a 130v three-phase multi-level inverter was Implemented and tested. The experimental results show that the output line voltage and acoustic noise harmonics spectra of an inverter have broadening effect of harmonics, as only simple synthesis of fixed frequency carries.

LCD 디스플레이의 대형화에 따라 백라이트용 냉음극 방전램프(Cold Cathode Fluorescent Lamp)는 길어지고 있으며, 하나의 램프를 이용한 백라이트는 휘도의 한계가 있어 대형 디스플레이에서는 램프를 병렬로 사용하여 필요한 휘도를 만들고 있다. 본 논문에서는 냉음극 방전램프 16개를 사용하는 37인치 LCD TV용 대형 백라이트 구동을 위한 인버터를 각각의 램프들이 입력조건에 대해 동일한 출력을 갖도록 설계하였다. 기존의 냉음극 방전램프의 구동방식인 하이-로우(H-L) 방식에서의 문제점을 보완하여 하이-하이(H-H) 방식을 채택하므로서 램프간의 휘도편차를 개선하였고 향후에 상용화가 가능함을 보였다.

This paper presents a method of detecting rotor position for single phase Switched Reluctance Motors(SRMs) using searchs coil. In the single phase SRM, mainly Hall effect sensors or photo interrupters have been used to detect the rotor position. But these sensors cause high cost and increase the volume of the motor, Furthermore when the motor is used in very hostile environment like high temperature or pressure, its reliability goes down. In this paper, low cost and robust characteristics of rotor position detection method are focused in order to compensate for disadvantage of existing sensors. Search coils wound around the stator pole are used for detection of the rotor position in single phase SRM. Rotor position detection is achieved through electromotive force patterns induced by time-varying flux linkage in the search coil. The validity of the method is verified by experimental results.

액정 디스플레이 (LCD: Liquid Crystal Display)의 광원은 주로 냉음극 방전램프 (CCFL: Cold Cathode Fluorescent Lamp)가 사용되고 있으며, 19인치급 이하의 LCD 백라이트 인버터의 램프 구동방식은 가장 일반적인 램프 구동방식인 H-L(High-Low) 방식을 채택하여 사용하고 있다. 그러나 21인치 이상의 중 ${\cdot}$ 대형 LCD 백라이트 인버터는 소형 LCD 에 비해 보다 높은 구동 전압 ${\cdot}$ 전류가 필요함에 따라 기존의 H-L(High-Low) 방식이 아닌 H-H(High-High) 방식 사용하고 있다. 본 논문에서는 대형 LCD 백라이트 인버터에 주로 사용되고 있는 H-H(High-High) 방식을 압전 인버터(Piezoelectric Inverter)에 적용하여 H-L(High-Low) 램프구동 방식과 비교 하였으며, H-H(High-High) 램프구동방식을 통한 멀티램프 구동과 효율, 휘도가 우수함을 검증하였다.

This paper describes the acoustic noise spectra of the pseudo-random carrier modulation technique according to the different PRBS(Pseudo Random Binary Sequence) bits. To confirm the validity of the proposed method, a 130v three-phase 5-level inverter motor drives was implemented. The harmonics spectra broadening effect of pseudo random carrier and the acoustic noise radiated from the inverter drives were discussed and verified according to the different bits of shift resister operating as PRBS.

본 연구에서는 유도 진동기의 파워 스펙트럼의 확산을 위한 LF2470 DSP기반 Hybrid Random PWM을 제안하였다. 제안된 방법은 Lead-Lag 랜덤 비트를 발생하기 위한 PRBS (Pseudo-Random Binary Sequence)와 PRBS와 논리적 비교를 위한 삼각파 랜덤 캐리어로 이루어진다. 또한 DSP에 의하여 랜덤 수 및 PRBS 그리고 3상 기준 정현파를 실시간으로 발생하며, DSP외부의 주파수 변조기 MAX038에 의하여 랜덤 주파수의 캐리어를 발생한다. 본 연구의 타당성 검증을 위하여 제안된 기법을 3상 유도전동기 구동장치에 적용하였으며, 종전의 방법과 전압 및 전류 그리고 전동기 소음 스펙트럼을 비교 검토하였다.

본 연구에서는 카오스 랜덤 캐리어 PWM에 의한 3상 유도 전동기의 스위칭 소음 저감에 대하여 다루고 있다. 랜덤 수 발생기로서는 종전부터 사용해 온 선형일치발생기(LCG)대신에 Logistic map의 분기트리를 사용하였다. 카오스 랜덤 수 발생은 80C196 마이크로 콘트롤러가 담당하고 있으며, 80C196으로부터 발생된 카오스 랜덤 수와 MAX038에 의하여 삼각파 랜덤 캐리어가 발생되고 있다. 1.5kw급 3상 유도전동기 구동 시스템에 카오스 랜덤 PWM와 종전의 방법을 적용하여 전동기 전압 및 전류 그리고 스위칭 소음의 스펙트럼을 고찰하였다.

최근 산업 분야에 걸쳐서 고속, 고정밀도의 요구사항에 따라, 회전 모터와 볼 스크류, 벨트를 이용한 직선구동방식보다 빠르고 정확하며, 효율이 높은 직접구동 방식의 리니어모터 및 컨트롤러의 개발이 요구되고 있다. 이런 상황에 고속 연산을 수행할 수 있는 DSP(Digital Signal Processor)의 사용이 불가피하며, 기존의 칩들은 A/D변환기, PWM발생장치 등이 내장되지 않아 제어장치의 부품 수증가 및 복잡성을 피할 수 없었다. 따라서 본 논문에서는 SVPWM(Space Vector Pulse Width Modulation) 및 QEP(Quadrature Encoder Pulse) 회로와 PWM 발생기, 12bit의 고속 A/D변환기, 파워 드라이버보호회로 등을 내장한 TMS320F2812 DSP를 사용하여 반도체장비분야, 자동화분야 등에 사용되는 LBLDCM의 제어를 가능하게 만들었다. 또한, 기존의 DSP 시리즈 보다 연산속도가 고속화되어 고속연산에 의한 시간적 제한을 극복 할 수 있게 되었고, 제어에 필요한 하드웨어적인 기능들을 내장하고 있어서 주변회로가 필요 없게 되었다. 따라서 하드웨어의 간소화와 개발 시간의 단축 및 신뢰도의 향상과 모터 효율의 향상을 가져오도록 하였다. 제안된 제어장치는 제작되어, 실험을 통하여 그 타당성을 입증하였다.

In this paper, a constant frequency phase shifting PWM controlled voltage source full bridge-type series load resonant high-frequency inverter using the IGBT power modules is presented for innovative consumer electromagnetic induction heating applications such as a hot water producer, steamer and super heated steamer. The full bridge arm side link passive quasi-resonant capacitor snubbers in parallel with the each power semiconductor device and high frequency AC load side linked active edge inductive snubber-assisted series load resonant tank soft switching inverter with a constant frequency phase shifted PWM control scheme is discussed and evaluated on the basis of the simulation and experimental results. It is proved from a practical point of view that the series load resonant and edge resonant hybrid high-frequency soft switching PWM inverter topology, what is called class DE type. including the variable-power variable-frequency(VPVF) regulation function can expand zero voltage soft switching commutation range even under low output power setting ranges, which is more suitable and acceptable for induction heated dual packs fluid heater developed newly for consumer power utilizations. Furthermore, even in the lower output power regulation mode of this high-frequency load resonant tank high frequency inverter circuit it is verified that this inverter can achieve ZVS with the aid of the single auxiliary inductor snubber.

This paper presents the steady-state characteristics of the multi-phase interleaved converters in discontinuous inductor current mode(DICM). The full-order averaged model is derived, and the conversion ratio and efficiency are presented.

This paper is aimed at presenting a proton exchange membrane ( PEM ) fuel cell stack. The fuel cell electrical output voltage and current (V-I) characteristic is described for the first time by a simplified closed form suitable. The characteristics obtained from the simulation are compared with the experimental results on a Ballard commercial fuel cell stack as well as to the manufacturer given data.

This paper addresses the small-signal analysis of the multi-phase interleaved boost converter with the coupled inductors operated in the continuous inductor current mode. The generalized and analytical expressions for the transfer functions of interest are derived for various inductor couplings. The dynamic characteristics are analyzed according to the inductor couplings and verified experimentally. The proposed frequency models will be very useful to design the dynamic controllers of the multi-phase interleaved boost converters.

이 논문은 부스트 하프 브릿지 1단 인버터기술을 혼합한 나아진 소프트스위칭 PWM 전력공급이 대체로 관계한다. 동작원리는 등가회로와 동작파형을 사용하여 설명하고 있다. 유효주파수 AC 동작 실행 시 1단 전력변환에 고주파 AC 전력변환 회로는 실험결과의 기초를 설명하고 평가한다. 전력변동률 대 고주파 듀티 사이클 특성과 전력변환 효율특성을 이전에 개발된 고주파와 비교하여 인버터전력소실을 나타냈다. 그것의 효과는 관찰의 실행 포인트로부터 실험 결과의 기초를 충분히 증명한다.