• Journal of ILASS-Korea
• /
• v.14 no.3
• /
• pp.97-102
• /
• 2009

The spray characteristics of the high speed rotating fuel injection system were studied. The five variants of rotating fuel nozzle were used by spray test. The diameter of single column injection orifices are varied from 1 mm, 2 mm, 3 mm, 4 mm and 5 mm. We constructed high speed rotating test rig and measured droplet size by PDPA (Phase Doppler Particle Analyzer) system. Also spray was visualized by using high speed camera. In the test results, we could understand that length of liquid column from the injection orifice is mainly controlled by the rotational speeds. SMD is decreased with increasing injection orifice diameter and rotational speeds. Furthermore, from the comparison to the theoritical calculation, we confirmed that SMD is influenced by the liquid film thickness which is formed inner surface of injection orifice.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.140-146
• /
• 2002

High speed rotating machines can be very sensitive to rotating mass unbalance that is a major source of harmful vibration for many types of rotating machinery. So, the balancing procedure is needed for all high-speed rotating system. To save the time and cost of off-line balancing, many researchers have developed the on-line balancing devices and methods. In this paper, an active balancing device, which is an electro-magnetic type, is developed and the active balancing algorithm using influence coefficient method is also proposed. The active balancing experiment for flexible rotors during operation is performed by an active balancing device. As a result, controlled unbalance responses are below the vibration limit at all rotating speed ranges with critical speed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.116-120
• /
• 2003

In general, industrial rotating machinery have been designed to have critical speed that is above operating speed. But nowadays, they should be operated more than the first critical speed as usual with the trend of high speed and high performance of rotating machinery. Therefore, it is important to predict the accuracy rotordynamic characteristics of the high speed rotating system in advance. In this paper, the results of rotordynamic analysis about FWP(Feed Water Pump) drive turbine rotor are showed. Because the FWP drive turbine analyzed is high speed machinery operated more than the operation speed of conventional FWP drive turbine, Seismic response analysis as well as unbalance response analysis is done in order to improve the reliability of the new turbine rotor-bearing system.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.6
• /
• pp.148-158
• /
• 2001

In this paper, Automatic Dynamic Balancer(ADB) was simulated and investigated to use at the high speed rotating chuck for the friction welding. In the limited computer simulations and experiments that have been presently carried out, several conclusions have been found. Above critical speed of the rotating system, ADB can balance the rotating disk. Therefore, it can be predicted that ADB can make an uniform flash during the friction welding.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.3 s.96
• /
• pp.297-305
• /
• 2005

A high-speed spindle can be very sensitive to rotating mass unbalance which has harmful effect on many machine tools. Therefore, the balancing procedure to reducevibration in rotating system is certainly needed for all high-speed spindles. An active balancing program using influence coefficient method and an active balancing device of an electro-magnetic type have been applied to the developed high-speed spindle system in this study. A reliable gain-scheduling control using influence coefficients of the reference model although system characteristics are changed is applied. The stability of reference influence coefficients is verified by frequency response functions. The active balancing experiment for the developed high-speed spindle during operation is well performed with an active balancing program and device. As a result, controlled unbalance responses are below the vibration limit at all rotating speed ranges with critical speed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.1 s.244
• /
• pp.32-41
• /
• 2006

We analyzed the non-Newtonian and non-isothermal flow in the melt conveying zone in co-rotating and counter-rotating screw extruder system with the commercial code, STAR-CD, and compared the mixing performance with respect to screw speed and rotating direction. The viscosity of fluid was described by power-law model. The dynamics of mixing was studied numerically by tracking the motion of particles in a twin screw extruder system. The extent of mixing was characterized in terms of the residence time distribution and average strain. The results showed that high screw speed decreases the residence time but increases the shear rate. Therefore higher screw speed increases the strain and has better mixing performance. Counter-rotating screw extruder system and co-rotating screw extruder has the similar shear rate with the same screw speed in spite of different rotating direction. However, the counter-rotating screw has good mixing performance, which is resulted from longer residence time than that of co-rotating screw extruder.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.3
• /
• pp.193-198
• /
• 2003

A rotor dynamic analysis is implemented to confirm the vibration stability of the high speed centrifugal chiller coupled with gear system. As the rotating speed of the centrifugal chiller under investigated is increased up to 17,605 rpm at the pinion rotating part, the bearing instability is getting higher and, furthermore, the rotor-bearing system might experience a few critical speed which lead to system failure due to the excessive vibration. In this study, considering the loading capacity and stability conditions, offset journal bearings are adopted for the pinion rotating system and general cylindrical bearing are used for motor part. From the modal analysis, the system is found to be stable as the synchronous rotating frequency does not come across with any whirl natural frequency and, in addition, the critical damping ratio which shows the damping characteristics of the system are positive over the all operating ranges. From these results the authors confirm the vibration stability of the rotor-bearing system suggested in this study.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.400.2-400
• /
• 2002

Recently rotating machines have became high speed and high Power and light weight. Bearings are one of the main components which influence power loss and stability of rotating machines. Appropriate bearing should be selected with considering characteristics of rotating machine. Floating ring journal bearing(FIB) consists of an inner film and outer film, and possess high damping and stability. FJB has been for adopted into turbocharger for the high stability at high operating speed. (omitted)

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.48-53
• /
• 2001

In order to increase productivity and efficiency, high-speed rotating machines become popular these days. The high-speed rotating machine is likely to vibrate and cause machine failure even though it has small unbalance. Therefore, a balancing technique is studied in this paper. Off-line balancing methods are inadequate to solve unbalance vibration problem occurring in the field due to flexible rotor effect, faster tool change, and shorter spin-up and down, etc. An active balancing is suggested to allow re-balancing of the entire rotating assembly in the machine when a tool is changed. This paper shows how to identify the dynamics of the system using influence coefficient and suggest an active balancing technique based on influence coefficient method for high-speed spindle system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.280-283
• /
• 2005

This study performed by a previous research for the applying expert system to active vibration control algorithm. In order to increase productivity and efficiency, high-speed rotating machines become popular these days. They are likely to vibrate and cause machine failure even though they have small unbalance. Therefore, a high-speed rotating machine needs a balancing technique. ISO 11342 classifies flexible rotors in accordance with their balancing requirements and establishes methods of assessment of residual unbalance. But, even if they finished balancing work, they have harmful effect vibration under the high-speed rotating environment. This vibration effect is very small, but it must be removed for the improvement of the rotor's spin accuracy. This paper introduces a new active control method that remove the exciting force by a phase control. For this method, the high-speed rotating rotor was reconstructed by a flexible rotor model. The forces which excite the rotating system suppose cyclic forces, we obtain the responses by numerical method. And then through the pattern analysis about the vibraton responses, the controler generate the control force with the reverse phase and similar magnitude. This paper suggest an phase control method and shows how to improve the rotating vibration accuracy of the flexible rotor dynamics system using phase control method.